Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 85 insertions, 0 deletions

diff --git a/Documentation/ABI/testing/sysfs-driver-hid-wiimote b/Documentation/ABI/testing/sysfs-driver-hid-wiimote
new file mode 100644
index 000000000..3bf43d9dc
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-hid-wiimote
@@ -0,0 +1,85 @@
+What:		/sys/bus/hid/drivers/wiimote/<dev>/led1
+What:		/sys/bus/hid/drivers/wiimote/<dev>/led2
+What:		/sys/bus/hid/drivers/wiimote/<dev>/led3
+What:		/sys/bus/hid/drivers/wiimote/<dev>/led4
+Date:		July 2011
+KernelVersion:	3.1
+Contact:	David Herrmann <dh.herrmann@googlemail.com>
+Description:	Make it possible to set/get current led state. Reading from it
+		returns 0 if led is off and 1 if it is on. Writing 0 to it
+		disables the led, writing 1 enables it.
+
+What:		/sys/bus/hid/drivers/wiimote/<dev>/extension
+Date:		August 2011
+KernelVersion:	3.2
+Contact:	David Herrmann <dh.herrmann@gmail.com>
+Description:	This file contains the currently connected and initialized
+		extensions. It can be one of: none, motionp, nunchuck, classic,
+		motionp+nunchuck, motionp+classic
+		motionp is the official Nintendo Motion+ extension, nunchuck is
+		the official Nintendo Nunchuck extension and classic is the
+		Nintendo Classic Controller extension. The motionp extension can
+		be combined with the other two.
+
+		Starting with kernel-version 3.11 Motion Plus hotplugging is
+		supported and if detected, it's no longer reported as static
+		extension. You will get uevent notifications for the motion-plus
+		device then.
+
+What:		/sys/bus/hid/drivers/wiimote/<dev>/devtype
+Date:		May 2013
+KernelVersion:	3.11
+Contact:	David Herrmann <dh.herrmann@gmail.com>
+Description:	While a device is initialized by the wiimote driver, we perform
+		a device detection and signal a "change" uevent after it is
+		done. This file shows the detected device type. "pending" means
+		that the detection is still ongoing, "unknown" means, that the
+		device couldn't be detected or loaded. "generic" means, that the
+		device couldn't be detected but supports basic Wii Remote
+		features and can be used.
+		Other strings for each device-type are available and may be
+		added if new device-specific detections are added.
+		Currently supported are:
+
+			============= =======================================
+			gen10:        First Wii Remote generation
+			gen20:        Second Wii Remote Plus generation
+				      (builtin MP)
+			balanceboard: Wii Balance Board
+			============= =======================================
+
+What:		/sys/bus/hid/drivers/wiimote/<dev>/bboard_calib
+Date:		May 2013
+KernelVersion:	3.11
+Contact:	David Herrmann <dh.herrmann@gmail.com>
+Description:	This attribute is only provided if the device was detected as a
+		balance board. It provides a single line with 3 calibration
+		values for all 4 sensors. The values are separated by colons and
+		are each 2 bytes long (encoded as 4 digit hexadecimal value).
+		First, 0kg values for all 4 sensors are written, followed by the
+		17kg values for all 4 sensors and last the 34kg values for all 4
+		sensors.
+
+		Calibration data is already applied by the kernel to all input
+		values but may be used by user-space to perform other
+		transformations.
+
+What:		/sys/bus/hid/drivers/wiimote/<dev>/pro_calib
+Date:		October 2013
+KernelVersion:	3.13
+Contact:	David Herrmann <dh.herrmann@gmail.com>
+Description:	This attribute is only provided if the device was detected as a
+		pro-controller. It provides a single line with 4 calibration
+		values for all 4 analog sticks. Format is: "x1:y1 x2:y2". Data
+		is prefixed with a +/-. Each value is a signed 16bit number.
+		Data is encoded as decimal numbers and specifies the offsets of
+		the analog sticks of the pro-controller.
+
+		Calibration data is already applied by the kernel to all input
+		values but may be used by user-space to perform other
+		transformations.
+
+		Calibration data is detected by the kernel during device setup.
+		You can write "scan\n" into this file to re-trigger calibration.
+		You can also write data directly in the form "x1:y1 x2:y2" to
+		set the calibration values manually.