Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 137 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/chosen.txt b/Documentation/devicetree/bindings/chosen.txt
new file mode 100644
index 000000000..45e79172a
--- /dev/null
+++ b/Documentation/devicetree/bindings/chosen.txt
@@ -0,0 +1,137 @@
+The chosen node
+---------------
+
+The chosen node does not represent a real device, but serves as a place
+for passing data between firmware and the operating system, like boot
+arguments. Data in the chosen node does not represent the hardware.
+
+The following properties are recognized:
+
+
+kaslr-seed
+-----------
+
+This property is used when booting with CONFIG_RANDOMIZE_BASE as the
+entropy used to randomize the kernel image base address location. Since
+it is used directly, this value is intended only for KASLR, and should
+not be used for other purposes (as it may leak information about KASLR
+offsets). It is parsed as a u64 value, e.g.
+
+/ {
+	chosen {
+		kaslr-seed = <0xfeedbeef 0xc0def00d>;
+	};
+};
+
+Note that if this property is set from UEFI (or a bootloader in EFI
+mode) when EFI_RNG_PROTOCOL is supported, it will be overwritten by
+the Linux EFI stub (which will populate the property itself, using
+EFI_RNG_PROTOCOL).
+
+stdout-path
+-----------
+
+Device trees may specify the device to be used for boot console output
+with a stdout-path property under /chosen, as described in the Devicetree
+Specification, e.g.
+
+/ {
+	chosen {
+		stdout-path = "/serial@f00:115200";
+	};
+
+	serial@f00 {
+		compatible = "vendor,some-uart";
+		reg = <0xf00 0x10>;
+	};
+};
+
+If the character ":" is present in the value, this terminates the path.
+The meaning of any characters following the ":" is device-specific, and
+must be specified in the relevant binding documentation.
+
+For UART devices, the preferred binding is a string in the form:
+
+	<baud>{<parity>{<bits>{<flow>}}}
+
+where
+
+	baud	- baud rate in decimal
+	parity	- 'n' (none), 'o', (odd) or 'e' (even)
+	bits	- number of data bits
+	flow	- 'r' (rts)
+
+For example: 115200n8r
+
+Implementation note: Linux will look for the property "linux,stdout-path" or
+on PowerPC "stdout" if "stdout-path" is not found.  However, the
+"linux,stdout-path" and "stdout" properties are deprecated. New platforms
+should only use the "stdout-path" property.
+
+linux,booted-from-kexec
+-----------------------
+
+This property is set (currently only on PowerPC, and only needed on
+book3e) by some versions of kexec-tools to tell the new kernel that it
+is being booted by kexec, as the booting environment may differ (e.g.
+a different secondary CPU release mechanism)
+
+linux,usable-memory-range
+-------------------------
+
+This property (arm64 only) holds a base address and size, describing a
+limited region in which memory may be considered available for use by
+the kernel. Memory outside of this range is not available for use.
+
+This property describes a limitation: memory within this range is only
+valid when also described through another mechanism that the kernel
+would otherwise use to determine available memory (e.g. memory nodes
+or the EFI memory map). Valid memory may be sparse within the range.
+e.g.
+
+/ {
+	chosen {
+		linux,usable-memory-range = <0x9 0xf0000000 0x0 0x10000000>;
+	};
+};
+
+The main usage is for crash dump kernel to identify its own usable
+memory and exclude, at its boot time, any other memory areas that are
+part of the panicked kernel's memory.
+
+While this property does not represent a real hardware, the address
+and the size are expressed in #address-cells and #size-cells,
+respectively, of the root node.
+
+linux,elfcorehdr
+----------------
+
+This property (currently used only on arm64) holds the memory range,
+the address and the size, of the elf core header which mainly describes
+the panicked kernel's memory layout as PT_LOAD segments of elf format.
+e.g.
+
+/ {
+	chosen {
+		linux,elfcorehdr = <0x9 0xfffff000 0x0 0x800>;
+	};
+};
+
+While this property does not represent a real hardware, the address
+and the size are expressed in #address-cells and #size-cells,
+respectively, of the root node.
+
+linux,initrd-start and linux,initrd-end
+---------------------------------------
+
+These properties hold the physical start and end address of an initrd that's
+loaded by the bootloader. Note that linux,initrd-start is inclusive, but
+linux,initrd-end is exclusive.
+e.g.
+
+/ {
+	chosen {
+		linux,initrd-start = <0x82000000>;
+		linux,initrd-end = <0x82800000>;
+	};
+};