Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

5 files changed, 539 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt
new file mode 100644
index 000000000..f4df9e83b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt
@@ -0,0 +1,57 @@
+Freescale imx21 Framebuffer
+
+This framebuffer driver supports devices imx1, imx21, imx25, and imx27.
+
+Required properties:
+- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : One interrupt of the fb dev
+
+Required nodes:
+- display: Phandle to a display node as described in
+	Documentation/devicetree/bindings/display/panel/display-timing.txt
+	Additional, the display node has to define properties:
+	- bits-per-pixel: Bits per pixel
+	- fsl,pcr: LCDC PCR value
+	A display node may optionally define
+	- fsl,aus-mode: boolean to enable AUS mode (only for imx21)
+
+Optional properties:
+- lcd-supply: Regulator for LCD supply voltage.
+- fsl,dmacr: DMA Control Register value. This is optional. By default, the
+	register is not modified as recommended by the datasheet.
+- fsl,lpccr: Contrast Control Register value. This property provides the
+	default value for the contrast control register.
+	If that property is omitted, the register is zeroed.
+- fsl,lscr1: LCDC Sharp Configuration Register value.
+
+Example:
+
+	imxfb: fb@10021000 {
+		compatible = "fsl,imx21-fb";
+		interrupts = <61>;
+		reg = <0x10021000 0x1000>;
+		display = <&display0>;
+	};
+
+	...
+
+	display0: display0 {
+		model = "Primeview-PD050VL1";
+		bits-per-pixel = <16>;
+		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
+		display-timings {
+			native-mode = <&timing_disp0>;
+			timing_disp0: 640x480 {
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <112>;
+				hfront-porch = <36>;
+				hsync-len = <32>;
+				vback-porch = <33>;
+				vfront-porch = <33>;
+				vsync-len = <2>;
+				clock-frequency = <25000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
new file mode 100644
index 000000000..5a99490c1
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
@@ -0,0 +1,162 @@
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface ports
+  of IPU devices
+
+example:
+
+display-subsystem {
+	compatible = "fsl,display-subsystem";
+	ports = <&ipu_di0>;
+};
+
+
+Freescale i.MX IPUv3
+====================
+
+Required properties:
+- compatible: Should be "fsl,<chip>-ipu" where <chip> is one of
+  - imx51
+  - imx53
+  - imx6q
+  - imx6qp
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain sync interrupt and error interrupt,
+  in this order.
+- resets: phandle pointing to the system reset controller and
+          reset line index, see reset/fsl,imx-src.txt for details
+Additional required properties for fsl,imx6qp-ipu:
+- fsl,prg: phandle to prg node associated with this IPU instance
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Ports 0 and 1 should correspond to CSI0 and CSI1,
+  ports 2 and 3 should correspond to DI0 and DI1, respectively.
+
+example:
+
+ipu: ipu@18000000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx53-ipu";
+	reg = <0x18000000 0x080000000>;
+	interrupts = <11 10>;
+	resets = <&src 2>;
+
+	ipu_di0: port@2 {
+		reg = <2>;
+
+		ipu_di0_disp0: endpoint {
+			remote-endpoint = <&display_in>;
+		};
+	};
+};
+
+Freescale i.MX PRE (Prefetch Resolve Engine)
+============================================
+
+Required properties:
+- compatible: should be "fsl,imx6qp-pre"
+- reg: should be register base and length as documented in the
+  datasheet
+- clocks : phandle to the PRE axi clock input, as described
+  in Documentation/devicetree/bindings/clock/clock-bindings.txt and
+  Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
+- clock-names: should be "axi"
+- interrupts: should contain the PRE interrupt
+- fsl,iram: phandle pointing to the mmio-sram device node, that should be
+  used for the PRE SRAM double buffer.
+
+example:
+
+pre@21c8000 {
+	compatible = "fsl,imx6qp-pre";
+	reg = <0x021c8000 0x1000>;
+	interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
+	clocks = <&clks IMX6QDL_CLK_PRE0>;
+	clock-names = "axi";
+	fsl,iram = <&ocram2>;
+};
+
+Freescale i.MX PRG (Prefetch Resolve Gasket)
+============================================
+
+Required properties:
+- compatible: should be "fsl,imx6qp-prg"
+- reg: should be register base and length as documented in the
+  datasheet
+- clocks : phandles to the PRG ipg and axi clock inputs, as described
+  in Documentation/devicetree/bindings/clock/clock-bindings.txt and
+  Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
+- clock-names: should be "ipg" and "axi"
+- fsl,pres: phandles to the PRE units attached to this PRG, with the fixed
+  PRE as the first entry and the muxable PREs following.
+
+example:
+
+prg@21cc000 {
+	compatible = "fsl,imx6qp-prg";
+	reg = <0x021cc000 0x1000>;
+	clocks = <&clks IMX6QDL_CLK_PRG0_APB>,
+		 <&clks IMX6QDL_CLK_PRG0_AXI>;
+	clock-names = "ipg", "axi";
+	fsl,pres = <&pre1>, <&pre2>, <&pre3>;
+};
+
+Parallel display support
+========================
+
+Required properties:
+- compatible: Should be "fsl,imx-parallel-display"
+Optional properties:
+- interface-pix-fmt: How this display is connected to the
+  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
+  and "lvds666".
+- edid: verbatim EDID data block describing attached display.
+- ddc: phandle describing the i2c bus handling the display data
+  channel
+- port@[0-1]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Port 0 is the input port connected to the IPU display interface,
+  port 1 is the output port connected to a panel.
+
+example:
+
+disp0 {
+	compatible = "fsl,imx-parallel-display";
+	edid = [edid-data];
+	interface-pix-fmt = "rgb24";
+
+	port@0 {
+		reg = <0>;
+
+		display_in: endpoint {
+			remote-endpoint = <&ipu_di0_disp0>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+panel {
+	...
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&display_out>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/display/imx/hdmi.txt b/Documentation/devicetree/bindings/display/imx/hdmi.txt
new file mode 100644
index 000000000..6d021e71c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/hdmi.txt
@@ -0,0 +1,65 @@
+Freescale i.MX6 DWC HDMI TX Encoder
+===================================
+
+The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with a companion PHY IP.
+
+These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
+Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
+following device-specific properties.
+
+
+Required properties:
+
+- compatible : Shall be one of "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
+- reg: See dw_hdmi.txt.
+- interrupts: HDMI interrupt number
+- clocks: See dw_hdmi.txt.
+- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
+- ports: See dw_hdmi.txt. The DWC HDMI shall have between one and four ports,
+  numbered 0 to 3, corresponding to the four inputs of the HDMI multiplexer.
+  Each port shall have a single endpoint.
+- gpr : Shall contain a phandle to the iomuxc-gpr region containing the HDMI
+  multiplexer control register.
+
+Optional properties
+
+- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master
+  or the functionally-reduced I2C master contained in the DWC HDMI. When
+  connected to a system I2C master this property contains a phandle to that
+  I2C master controller.
+
+
+Example:
+
+	gpr: iomuxc-gpr@20e0000 {
+		/* ... */
+	};
+
+        hdmi: hdmi@120000 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                compatible = "fsl,imx6q-hdmi";
+                reg = <0x00120000 0x9000>;
+                interrupts = <0 115 0x04>;
+                gpr = <&gpr>;
+                clocks = <&clks 123>, <&clks 124>;
+                clock-names = "iahb", "isfr";
+                ddc-i2c-bus = <&i2c2>;
+
+                port@0 {
+                        reg = <0>;
+
+                        hdmi_mux_0: endpoint {
+                                remote-endpoint = <&ipu1_di0_hdmi>;
+                        };
+                };
+
+                port@1 {
+                        reg = <1>;
+
+                        hdmi_mux_1: endpoint {
+                                remote-endpoint = <&ipu1_di1_hdmi>;
+                        };
+                };
+        };
diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt
new file mode 100644
index 000000000..8e6e7d797
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/ldb.txt
@@ -0,0 +1,147 @@
+Device-Tree bindings for LVDS Display Bridge (ldb)
+
+LVDS Display Bridge
+===================
+
+The LVDS Display Bridge device tree node contains up to two lvds-channel
+nodes describing each of the two LVDS encoder channels of the bridge.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
+                Both LDB versions are similar, but i.MX6 has an additional
+                multiplexer in the front to select any of the four IPU display
+                interfaces as input for each LVDS channel.
+ - gpr : should be <&gpr> on i.MX53 and i.MX6q.
+         The phandle points to the iomuxc-gpr region containing the LVDS
+         control register.
+- clocks, clock-names : phandles to the LDB divider and selector clocks and to
+                        the display interface selector clocks, as described in
+                        Documentation/devicetree/bindings/clock/clock-bindings.txt
+        The following clocks are expected on i.MX53:
+                "di0_pll" - LDB LVDS channel 0 mux
+                "di1_pll" - LDB LVDS channel 1 mux
+                "di0" - LDB LVDS channel 0 gate
+                "di1" - LDB LVDS channel 1 gate
+                "di0_sel" - IPU1 DI0 mux
+                "di1_sel" - IPU1 DI1 mux
+        On i.MX6q the following additional clocks are needed:
+                "di2_sel" - IPU2 DI0 mux
+                "di3_sel" - IPU2 DI1 mux
+        The needed clock numbers for each are documented in
+        Documentation/devicetree/bindings/clock/imx5-clock.yaml, and in
+        Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
+
+Optional properties:
+ - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
+ - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
+               not used on i.MX6q
+ - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
+   be configured - one input will be distributed on both outputs in dual
+   channel mode
+
+LVDS Channel
+============
+
+Each LVDS Channel has to contain either an of graph link to a panel device node
+or a display-timings node that describes the video timings for the connected
+LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
+
+Required properties:
+ - reg : should be <0> or <1>
+ - port: Input and output port nodes with endpoint definitions as defined in
+   Documentation/devicetree/bindings/graph.txt.
+   On i.MX5, the internal two-input-multiplexer is used. Due to hardware
+   limitations, only one input port (port@[0,1]) can be used for each channel
+   (lvds-channel@[0,1], respectively).
+   On i.MX6, there should be four input ports (port@[0-3]) that correspond
+   to the four LVDS multiplexer inputs.
+   A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
+   to a panel input port. Optionally, the output port can be left out if
+   display-timings are used instead.
+
+Optional properties (required if display-timings are used):
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+ - display-timings : A node that describes the display timings as defined in
+   Documentation/devicetree/bindings/display/panel/display-timing.txt.
+ - fsl,data-mapping : should be "spwg" or "jeida"
+                      This describes how the color bits are laid out in the
+                      serialized LVDS signal.
+ - fsl,data-width : should be <18> or <24>
+
+example:
+
+gpr: iomuxc-gpr@53fa8000 {
+	/* ... */
+};
+
+ldb: ldb@53fa8008 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx53-ldb";
+	gpr = <&gpr>;
+	clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
+		 <&clks IMX5_CLK_LDB_DI1_SEL>,
+		 <&clks IMX5_CLK_IPU_DI0_SEL>,
+		 <&clks IMX5_CLK_IPU_DI1_SEL>,
+		 <&clks IMX5_CLK_LDB_DI0_GATE>,
+		 <&clks IMX5_CLK_LDB_DI1_GATE>;
+	clock-names = "di0_pll", "di1_pll",
+		      "di0_sel", "di1_sel",
+		      "di0", "di1";
+
+	/* Using an of-graph endpoint link to connect the panel */
+	lvds-channel@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lvds0_in: endpoint {
+				remote-endpoint = <&ipu_di0_lvds0>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	/* Using display-timings and fsl,data-mapping/width instead */
+	lvds-channel@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		display-timings {
+			/* ... */
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lvds1_in: endpoint {
+				remote-endpoint = <&ipu_di1_lvds1>;
+			};
+		};
+	};
+};
+
+panel: lvds-panel {
+	/* ... */
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&lvds0_out>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml b/Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml
new file mode 100644
index 000000000..f1f25aa79
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 NXP
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/display/imx/nxp,imx8mq-dcss.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: iMX8MQ Display Controller Subsystem (DCSS)
+
+maintainers:
+  - Laurentiu Palcu <laurentiu.palcu@nxp.com>
+
+description:
+
+  The DCSS (display controller sub system) is used to source up to three
+  display buffers, compose them, and drive a display using HDMI 2.0a(with HDCP
+  2.2) or MIPI-DSI. The DCSS is intended to support up to 4kp60 displays. HDR10
+  image processing capabilities are included to provide a solution capable of
+  driving next generation high dynamic range displays.
+
+properties:
+  compatible:
+    const: nxp,imx8mq-dcss
+
+  reg:
+    items:
+      - description: DCSS base address and size, up to IRQ steer start
+      - description: DCSS BLKCTL base address and size
+
+  interrupts:
+    items:
+      - description: Context loader completion and error interrupt
+      - description: DTG interrupt used to signal context loader trigger time
+      - description: DTG interrupt for Vblank
+
+  interrupt-names:
+    items:
+      - const: ctxld
+      - const: ctxld_kick
+      - const: vblank
+
+  clocks:
+    items:
+      - description: Display APB clock for all peripheral PIO access interfaces
+      - description: Display AXI clock needed by DPR, Scaler, RTRAM_CTRL
+      - description: RTRAM clock
+      - description: Pixel clock, can be driven either by HDMI phy clock or MIPI
+      - description: DTRC clock, needed by video decompressor
+
+  clock-names:
+    items:
+      - const: apb
+      - const: axi
+      - const: rtrm
+      - const: pix
+      - const: dtrc
+
+  assigned-clocks:
+    items:
+      - description: Phandle and clock specifier of IMX8MQ_CLK_DISP_AXI_ROOT
+      - description: Phandle and clock specifier of IMX8MQ_CLK_DISP_RTRM
+      - description: Phandle and clock specifier of either IMX8MQ_VIDEO2_PLL1_REF_SEL or
+                     IMX8MQ_VIDEO_PLL1_REF_SEL
+
+  assigned-clock-parents:
+    items:
+      - description: Phandle and clock specifier of IMX8MQ_SYS1_PLL_800M
+      - description: Phandle and clock specifier of IMX8MQ_SYS1_PLL_800M
+      - description: Phandle and clock specifier of IMX8MQ_CLK_27M
+
+  assigned-clock-rates:
+    items:
+      - description: Must be 800 MHz
+      - description: Must be 400 MHz
+
+  port:
+    type: object
+    description:
+      A port node pointing to the input port of a HDMI/DP or MIPI display bridge.
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx8mq-clock.h>
+    dcss: display-controller@32e00000 {
+        compatible = "nxp,imx8mq-dcss";
+        reg = <0x32e00000 0x2d000>, <0x32e2f000 0x1000>;
+        interrupts = <6>, <8>, <9>;
+        interrupt-names = "ctxld", "ctxld_kick", "vblank";
+        interrupt-parent = <&irqsteer>;
+        clocks = <&clk IMX8MQ_CLK_DISP_APB_ROOT>, <&clk IMX8MQ_CLK_DISP_AXI_ROOT>,
+                 <&clk IMX8MQ_CLK_DISP_RTRM_ROOT>, <&clk IMX8MQ_VIDEO2_PLL_OUT>,
+                 <&clk IMX8MQ_CLK_DISP_DTRC>;
+        clock-names = "apb", "axi", "rtrm", "pix", "dtrc";
+        assigned-clocks = <&clk IMX8MQ_CLK_DISP_AXI>, <&clk IMX8MQ_CLK_DISP_RTRM>,
+                          <&clk IMX8MQ_VIDEO2_PLL1_REF_SEL>;
+        assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>, <&clk IMX8MQ_SYS1_PLL_800M>,
+                                 <&clk IMX8MQ_CLK_27M>;
+        assigned-clock-rates = <800000000>,
+                               <400000000>;
+        port {
+            dcss_out: endpoint {
+                remote-endpoint = <&hdmi_in>;
+            };
+        };
+    };
+