diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/display/mediatek | |
parent | Initial commit. (diff) | |
download | linux-upstream/5.10.209.tar.xz linux-upstream/5.10.209.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
4 files changed, 475 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt new file mode 100644 index 000000000..121220745 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt @@ -0,0 +1,209 @@ +Mediatek display subsystem +========================== + +The Mediatek display subsystem consists of various DISP function blocks in the +MMSYS register space. The connections between them can be configured by output +and input selectors in the MMSYS_CONFIG register space. Pixel clock and start +of frame signal are distributed to the other function blocks by a DISP_MUTEX +function block. + +All DISP device tree nodes must be siblings to the central MMSYS_CONFIG node. +For a description of the MMSYS_CONFIG binding, see +Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt. + +DISP function blocks +==================== + +A display stream starts at a source function block that reads pixel data from +memory and ends with a sink function block that drives pixels on a display +interface, or writes pixels back to memory. All DISP function blocks have +their own register space, interrupt, and clock gate. The blocks that can +access memory additionally have to list the IOMMU and local arbiter they are +connected to. + +For a description of the display interface sink function blocks, see +Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt and +Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt. + +Required properties (all function blocks): +- compatible: "mediatek,<chip>-disp-<function>", one of + "mediatek,<chip>-disp-ovl" - overlay (4 layers, blending, csc) + "mediatek,<chip>-disp-ovl-2l" - overlay (2 layers, blending, csc) + "mediatek,<chip>-disp-rdma" - read DMA / line buffer + "mediatek,<chip>-disp-wdma" - write DMA + "mediatek,<chip>-disp-ccorr" - color correction + "mediatek,<chip>-disp-color" - color processor + "mediatek,<chip>-disp-dither" - dither + "mediatek,<chip>-disp-aal" - adaptive ambient light controller + "mediatek,<chip>-disp-gamma" - gamma correction + "mediatek,<chip>-disp-merge" - merge streams from two RDMA sources + "mediatek,<chip>-disp-split" - split stream to two encoders + "mediatek,<chip>-disp-ufoe" - data compression engine + "mediatek,<chip>-dsi" - DSI controller, see mediatek,dsi.txt + "mediatek,<chip>-dpi" - DPI controller, see mediatek,dpi.txt + "mediatek,<chip>-disp-mutex" - display mutex + "mediatek,<chip>-disp-od" - overdrive + the supported chips are mt2701, mt7623, mt2712 and mt8173. +- reg: Physical base address and length of the function block register space +- interrupts: The interrupt signal from the function block (required, except for + merge and split function blocks). +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. + For most function blocks this is just a single clock input. Only the DSI and + DPI controller nodes have multiple clock inputs. These are documented in + mediatek,dsi.txt and mediatek,dpi.txt, respectively. + An exception is that the mt8183 mutex is always free running with no clocks property. + +Required properties (DMA function blocks): +- compatible: Should be one of + "mediatek,<chip>-disp-ovl" + "mediatek,<chip>-disp-rdma" + "mediatek,<chip>-disp-wdma" + the supported chips are mt2701 and mt8173. +- larb: Should contain a phandle pointing to the local arbiter device as defined + in Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +- iommus: Should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. + +Examples: + +mmsys: clock-controller@14000000 { + compatible = "mediatek,mt8173-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + #clock-cells = <1>; +}; + +ovl0: ovl@1400c000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400c000 0 0x1000>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL0>; + iommus = <&iommu M4U_PORT_DISP_OVL0>; + mediatek,larb = <&larb0>; +}; + +ovl1: ovl@1400d000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400d000 0 0x1000>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL1>; + iommus = <&iommu M4U_PORT_DISP_OVL1>; + mediatek,larb = <&larb4>; +}; + +rdma0: rdma@1400e000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400e000 0 0x1000>; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA0>; + iommus = <&iommu M4U_PORT_DISP_RDMA0>; + mediatek,larb = <&larb0>; +}; + +rdma1: rdma@1400f000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400f000 0 0x1000>; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA1>; + iommus = <&iommu M4U_PORT_DISP_RDMA1>; + mediatek,larb = <&larb4>; +}; + +rdma2: rdma@14010000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x14010000 0 0x1000>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA2>; + iommus = <&iommu M4U_PORT_DISP_RDMA2>; + mediatek,larb = <&larb4>; +}; + +wdma0: wdma@14011000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14011000 0 0x1000>; + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA0>; + iommus = <&iommu M4U_PORT_DISP_WDMA0>; + mediatek,larb = <&larb0>; +}; + +wdma1: wdma@14012000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14012000 0 0x1000>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA1>; + iommus = <&iommu M4U_PORT_DISP_WDMA1>; + mediatek,larb = <&larb4>; +}; + +color0: color@14013000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14013000 0 0x1000>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR0>; +}; + +color1: color@14014000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14014000 0 0x1000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR1>; +}; + +aal@14015000 { + compatible = "mediatek,mt8173-disp-aal"; + reg = <0 0x14015000 0 0x1000>; + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_AAL>; +}; + +gamma@14016000 { + compatible = "mediatek,mt8173-disp-gamma"; + reg = <0 0x14016000 0 0x1000>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_GAMMA>; +}; + +ufoe@1401a000 { + compatible = "mediatek,mt8173-disp-ufoe"; + reg = <0 0x1401a000 0 0x1000>; + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_UFOE>; +}; + +dsi0: dsi@1401b000 { + /* See mediatek,dsi.txt for details */ +}; + +dpi0: dpi@1401d000 { + /* See mediatek,dpi.txt for details */ +}; + +mutex: mutex@14020000 { + compatible = "mediatek,mt8173-disp-mutex"; + reg = <0 0x14020000 0 0x1000>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MUTEX_32K>; +}; + +od@14023000 { + compatible = "mediatek,mt8173-disp-od"; + reg = <0 0x14023000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OD>; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt new file mode 100644 index 000000000..dc1ebd13c --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt @@ -0,0 +1,42 @@ +Mediatek DPI Device +=================== + +The Mediatek DPI function block is a sink of the display subsystem and +provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel +output bus. + +Required properties: +- compatible: "mediatek,<chip>-dpi" + the supported chips are mt2701, mt7623, mt8173 and mt8183. +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "engine", and "pll" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached HDMI or LVDS encoder chip. + +Optional properties: +- pinctrl-names: Contain "default" and "sleep". + +Example: + +dpi0: dpi@1401d000 { + compatible = "mediatek,mt8173-dpi"; + reg = <0 0x1401d000 0 0x1000>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_DPI_PIXEL>, + <&mmsys CLK_MM_DPI_ENGINE>, + <&apmixedsys CLK_APMIXED_TVDPLL>; + clock-names = "pixel", "engine", "pll"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dpi_pin_func>; + pinctrl-1 = <&dpi_pin_idle>; + + port { + dpi0_out: endpoint { + remote-endpoint = <&hdmi0_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt new file mode 100644 index 000000000..f06f24d40 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt @@ -0,0 +1,72 @@ +Mediatek DSI Device +=================== + +The Mediatek DSI function block is a sink of the display subsystem and can +drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual- +channel output. + +Required properties: +- compatible: "mediatek,<chip>-dsi" +- the supported chips are mt2701, mt7623, mt8173 and mt8183. +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "engine", "digital", and "hs" +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached DSI panel or DSI-to-eDP encoder chip. + +MIPI TX Configuration Module +============================ + +The MIPI TX configuration module controls the MIPI D-PHY. + +Required properties: +- compatible: "mediatek,<chip>-mipi-tx" +- the supported chips are mt2701, 7623, mt8173 and mt8183. +- reg: Physical base address and length of the controller's registers +- clocks: PLL reference clock +- clock-output-names: name of the output clock line to the DSI encoder +- #clock-cells: must be <0>; +- #phy-cells: must be <0>. + +Optional properties: +- drive-strength-microamp: adjust driving current, should be 3000 ~ 6000. And + the step is 200. +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If + unspecified default values shall be used. +- nvmem-cell-names: Should be "calibration-data" + +Example: + +mipi_tx0: mipi-dphy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10215000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + #clock-cells = <0>; + #phy-cells = <0>; + drive-strength-microamp = <4600>; + nvmem-cells= <&mipi_tx_calibration>; + nvmem-cell-names = "calibration-data"; +}; + +dsi0: dsi@1401b000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401b000 0 0x1000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt new file mode 100644 index 000000000..6b1c58640 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt @@ -0,0 +1,152 @@ +Mediatek HDMI Encoder +===================== + +The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from +its parallel input. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi". +- the supported chips are mt2701, mt7623 and mt8173 +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "pll", "bclk", and "spdif". +- phys: phandle link to the HDMI PHY node. + See Documentation/devicetree/bindings/phy/phy-bindings.txt for details. +- phy-names: must contain "hdmi" +- mediatek,syscon-hdmi: phandle link and register offset to the system + configuration registers. For mt8173 this must be offset 0x900 into the + MMSYS_CONFIG region: <&mmsys 0x900>. +- ports: A node containing input and output port nodes with endpoint + definitions as documented in Documentation/devicetree/bindings/graph.txt. +- port@0: The input port in the ports node should be connected to a DPI output + port. +- port@1: The output port in the ports node should be connected to the input + port of a connector node that contains a ddc-i2c-bus property, or to the + input port of an attached bridge chip, such as a SlimPort transmitter. + +HDMI CEC +======== + +The HDMI CEC controller handles hotplug detection and CEC communication. + +Required properties: +- compatible: Should be "mediatek,<chip>-cec" +- the supported chips are mt7623 and mt8173 +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clock + +HDMI DDC +======== + +The HDMI DDC i2c controller is used to interface with the HDMI DDC pins. +The Mediatek's I2C controller is used to interface with I2C devices. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi-ddc" +- the supported chips are mt7623 and mt8173 +- reg: Physical base address and length of the controller's registers +- clocks: device clock +- clock-names: Should be "ddc-i2c". + +HDMI PHY +======== + +The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel +output and drives the HDMI pads. + +Required properties: +- compatible: "mediatek,<chip>-hdmi-phy" +- the supported chips are mt2701, mt7623 and mt8173 +- reg: Physical base address and length of the module's registers +- clocks: PLL reference clock +- clock-names: must contain "pll_ref" +- clock-output-names: must be "hdmitx_dig_cts" on mt8173 +- #phy-cells: must be <0> +- #clock-cells: must be <0> + +Optional properties: +- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa +- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c + +Example: + +cec: cec@10013000 { + compatible = "mediatek,mt8173-cec"; + reg = <0 0x10013000 0 0xbc>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_CEC>; +}; + +hdmi_phy: hdmi-phy@10209100 { + compatible = "mediatek,mt8173-hdmi-phy"; + reg = <0 0x10209100 0 0x24>; + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>; + clock-names = "pll_ref"; + clock-output-names = "hdmitx_dig_cts"; + mediatek,ibias = <0xa>; + mediatek,ibias_up = <0x1c>; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +hdmi_ddc0: i2c@11012000 { + compatible = "mediatek,mt8173-hdmi-ddc"; + reg = <0 0x11012000 0 0x1c>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_I2C5>; + clock-names = "ddc-i2c"; +}; + +hdmi0: hdmi@14025000 { + compatible = "mediatek,mt8173-hdmi"; + reg = <0 0x14025000 0 0x400>; + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_HDMI_PIXEL>, + <&mmsys CLK_MM_HDMI_PLLCK>, + <&mmsys CLK_MM_HDMI_AUDIO>, + <&mmsys CLK_MM_HDMI_SPDIF>; + clock-names = "pixel", "pll", "bclk", "spdif"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pin>; + phys = <&hdmi_phy>; + phy-names = "hdmi"; + mediatek,syscon-hdmi = <&mmsys 0x900>; + assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>; + assigned-clock-parents = <&hdmi_phy>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi0_in: endpoint { + remote-endpoint = <&dpi0_out>; + }; + }; + + port@1 { + reg = <1>; + + hdmi0_out: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; +}; + +connector { + compatible = "hdmi-connector"; + type = "a"; + ddc-i2c-bus = <&hdmiddc0>; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; +}; |