Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 249 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt
new file mode 100644
index 000000000..b9a64d3ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/dsi.txt
@@ -0,0 +1,249 @@
+Qualcomm Technologies Inc. adreno/snapdragon DSI output
+
+DSI Controller:
+Required properties:
+- compatible:
+  * "qcom,mdss-dsi-ctrl"
+- reg: Physical base address and length of the registers of controller
+- reg-names: The names of register regions. The following regions are required:
+  * "dsi_ctrl"
+- interrupts: The interrupt signal from the DSI block.
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: Phandles to device clocks.
+- clock-names: the following clocks are required:
+  * "mdp_core"
+  * "iface"
+  * "bus"
+  * "core_mmss"
+  * "byte"
+  * "pixel"
+  * "core"
+  For DSIv2, we need an additional clock:
+   * "src"
+  For DSI6G v2.0 onwards, we need also need the clock:
+   * "byte_intf"
+- assigned-clocks: Parents of "byte" and "pixel" for the given platform.
+- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
+  by a DSI PHY block. See [1] for details on clock bindings.
+- vdd-supply: phandle to vdd regulator device node
+- vddio-supply: phandle to vdd-io regulator device node
+- vdda-supply: phandle to vdda regulator device node
+- phys: phandle to DSI PHY device node
+- phy-names: the name of the corresponding PHY device
+- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
+- ports: Contains 2 DSI controller ports as child nodes. Each port contains
+  an endpoint subnode as defined in [2] and [3].
+
+Optional properties:
+- panel@0: Node of panel connected to this DSI controller.
+  See files in [4] for each supported panel.
+- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
+  driving a panel which needs 2 DSI links.
+- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
+  the master link of the 2-DSI panel.
+- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
+  driving a 2-DSI panel whose 2 links need receive command simultaneously.
+- pinctrl-names: the pin control state names; should contain "default"
+- pinctrl-0: the default pinctrl state (active)
+- pinctrl-n: the "sleep" pinctrl state
+- ports: contains DSI controller input and output ports as children, each
+  containing one endpoint subnode.
+
+  DSI Endpoint properties:
+  - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
+    input endpoint. For port@1, set to the MDP interface output. See [2] for
+    device graph info.
+
+  - data-lanes: this describes how the physical DSI data lanes are mapped
+    to the logical lanes on the given platform. The value contained in
+    index n describes what physical lane is mapped to the logical lane n
+    (DATAn, where n lies between 0 and 3). The clock lane position is fixed
+    and can't be changed. Hence, they aren't a part of the DT bindings. See
+    [3] for more info on the data-lanes property.
+
+    For example:
+
+    data-lanes = <3 0 1 2>;
+
+    The above mapping describes that the logical data lane DATA0 is mapped to
+    the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
+    to phys DATA1 and logic DATA3 to phys DATA2.
+
+    There are only a limited number of physical to logical mappings possible:
+    <0 1 2 3>
+    <1 2 3 0>
+    <2 3 0 1>
+    <3 0 1 2>
+    <0 3 2 1>
+    <1 0 3 2>
+    <2 1 0 3>
+    <3 2 1 0>
+
+DSI PHY:
+Required properties:
+- compatible: Could be the following
+  * "qcom,dsi-phy-28nm-hpm"
+  * "qcom,dsi-phy-28nm-lp"
+  * "qcom,dsi-phy-20nm"
+  * "qcom,dsi-phy-28nm-8960"
+  * "qcom,dsi-phy-14nm"
+  * "qcom,dsi-phy-14nm-660"
+  * "qcom,dsi-phy-10nm"
+  * "qcom,dsi-phy-10nm-8998"
+  * "qcom,dsi-phy-7nm"
+  * "qcom,dsi-phy-7nm-8150"
+- reg: Physical base address and length of the registers of PLL, PHY. Some
+  revisions require the PHY regulator base address, whereas others require the
+  PHY lane base address. See below for each PHY revision.
+- reg-names: The names of register regions. The following regions are required:
+  For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
+  * "dsi_pll"
+  * "dsi_phy"
+  * "dsi_phy_regulator"
+  For DSI 14nm, 10nm and 7nm PHYs:
+  * "dsi_pll"
+  * "dsi_phy"
+  * "dsi_phy_lane"
+- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
+  2 clocks: A byte clock (index 0), and a pixel clock (index 1).
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: Phandles to device clocks. See [1] for details on clock bindings.
+- clock-names: the following clocks are required:
+  * "iface"
+  * "ref" (only required for new DTS files/entries)
+  For 28nm HPM/LP, 28nm 8960 PHYs:
+- vddio-supply: phandle to vdd-io regulator device node
+  For 20nm PHY:
+- vddio-supply: phandle to vdd-io regulator device node
+- vcca-supply: phandle to vcca regulator device node
+  For 14nm PHY:
+- vcca-supply: phandle to vcca regulator device node
+  For 10nm and 7nm PHY:
+- vdds-supply: phandle to vdds regulator device node
+
+Optional properties:
+- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
+  regulator is wanted.
+- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode
+					panels in microseconds. Driver uses this number to adjust
+					the clock rate according to the expected transfer time.
+					Increasing this value would slow down the mdp processing
+					and can result in slower performance.
+					Decreasing this value can speed up the mdp processing,
+					but this can also impact power consumption.
+					As a rule this time should not be higher than the time
+					that would be expected with the processing at the
+					dsi link rate since anyways this would be the maximum
+					transfer time that could be achieved.
+					If ping pong split is enabled, this time should not be higher
+					than two times the dsi link rate time.
+					If the property is not specified, then the default value is 14000 us.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/graph.txt
+[3] Documentation/devicetree/bindings/media/video-interfaces.txt
+[4] Documentation/devicetree/bindings/display/panel/
+
+Example:
+	dsi0: dsi@fd922800 {
+		compatible = "qcom,mdss-dsi-ctrl";
+		qcom,dsi-host-index = <0>;
+		interrupt-parent = <&mdp>;
+		interrupts = <4 0>;
+		reg-names = "dsi_ctrl";
+		reg = <0xfd922800 0x200>;
+		power-domains = <&mmcc MDSS_GDSC>;
+		clock-names =
+			"bus",
+			"byte",
+			"core",
+			"core_mmss",
+			"iface",
+			"mdp_core",
+			"pixel";
+		clocks =
+			<&mmcc MDSS_AXI_CLK>,
+			<&mmcc MDSS_BYTE0_CLK>,
+			<&mmcc MDSS_ESC0_CLK>,
+			<&mmcc MMSS_MISC_AHB_CLK>,
+			<&mmcc MDSS_AHB_CLK>,
+			<&mmcc MDSS_MDP_CLK>,
+			<&mmcc MDSS_PCLK0_CLK>;
+
+		assigned-clocks =
+				 <&mmcc BYTE0_CLK_SRC>,
+				 <&mmcc PCLK0_CLK_SRC>;
+		assigned-clock-parents =
+				 <&dsi_phy0 0>,
+				 <&dsi_phy0 1>;
+
+		vdda-supply = <&pma8084_l2>;
+		vdd-supply = <&pma8084_l22>;
+		vddio-supply = <&pma8084_l12>;
+
+		phys = <&dsi_phy0>;
+		phy-names ="dsi-phy";
+
+		qcom,dual-dsi-mode;
+		qcom,master-dsi;
+		qcom,sync-dual-dsi;
+
+		qcom,mdss-mdp-transfer-time-us = <12000>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&dsi_active>;
+		pinctrl-1 = <&dsi_suspend>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				dsi0_in: endpoint {
+					remote-endpoint = <&mdp_intf1_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				dsi0_out: endpoint {
+					remote-endpoint = <&panel_in>;
+					data-lanes = <0 1 2 3>;
+				};
+			};
+		};
+
+		panel: panel@0 {
+			compatible = "sharp,lq101r1sx01";
+			reg = <0>;
+			link2 = <&secondary>;
+
+			power-supply = <...>;
+			backlight = <...>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+
+	dsi_phy0: dsi-phy@fd922a00 {
+		compatible = "qcom,dsi-phy-28nm-hpm";
+		qcom,dsi-phy-index = <0>;
+		reg-names =
+			"dsi_pll",
+			"dsi_phy",
+			"dsi_phy_regulator";
+		reg =   <0xfd922a00 0xd4>,
+			<0xfd922b00 0x2b0>,
+			<0xfd922d80 0x7b>;
+		clock-names = "iface";
+		clocks = <&mmcc MDSS_AHB_CLK>;
+		#clock-cells = <1>;
+		vddio-supply = <&pma8084_l12>;
+
+		qcom,dsi-phy-regulator-ldo-mode;
+	};