Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

2 files changed, 595 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra114-mipi.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra114-mipi.txt
new file mode 100644
index 000000000..e4a25cedc
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra114-mipi.txt
@@ -0,0 +1,41 @@
+NVIDIA Tegra MIPI pad calibration controller
+
+Required properties:
+- compatible: "nvidia,tegra<chip>-mipi"
+- reg: Physical base address and length of the controller's registers.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - mipi-cal
+- #nvidia,mipi-calibrate-cells: Should be 1. The cell is a bitmask of the pads
+  that need to be calibrated for a given device.
+
+User nodes need to contain an nvidia,mipi-calibrate property that has a
+phandle to refer to the calibration controller node and a bitmask of the pads
+that need to be calibrated.
+
+Example:
+
+	mipi: mipi@700e3000 {
+		compatible = "nvidia,tegra114-mipi";
+		reg = <0x700e3000 0x100>;
+		clocks = <&tegra_car TEGRA114_CLK_MIPI_CAL>;
+		clock-names = "mipi-cal";
+		#nvidia,mipi-calibrate-cells = <1>;
+	};
+
+	...
+
+	host1x@50000000 {
+		...
+
+		dsi@54300000 {
+			...
+
+			nvidia,mipi-calibrate = <&mipi 0x060>;
+
+			...
+		};
+
+		...
+	};
diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
new file mode 100644
index 000000000..ac63ae4a3
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
@@ -0,0 +1,554 @@
+NVIDIA Tegra host1x
+
+Required properties:
+- compatible: "nvidia,tegra<chip>-host1x"
+- reg: Physical base address and length of the controller's registers.
+  For pre-Tegra186, one entry describing the whole register area.
+  For Tegra186, one entry for each entry in reg-names:
+    "vm" - VM region assigned to Linux
+    "hypervisor" - Hypervisor region (only if Linux acts as hypervisor)
+- interrupts: The interrupt outputs from the controller.
+- #address-cells: The number of cells used to represent physical base addresses
+  in the host1x address space. Should be 1.
+- #size-cells: The number of cells used to represent the size of an address
+  range in the host1x address space. Should be 1.
+- ranges: The mapping of the host1x address space to the CPU address space.
+- clocks: Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - host1x
+
+The host1x top-level node defines a number of children, each representing one
+of the following host1x client modules:
+
+- mpe: video encoder
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-mpe"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - mpe
+
+- vi: video input
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-vi"
+  - reg: Physical base address and length of the controller registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - Tegra20/Tegra30/Tegra114/Tegra124:
+    - resets: Must contain an entry for each entry in reset-names.
+      See ../reset/reset.txt for details.
+    - reset-names: Must include the following entries:
+      - vi
+  - Tegra210:
+    - power-domains: Must include venc powergate node as vi is in VE partition.
+
+  ports (optional node)
+  vi can have optional ports node and max 6 ports are supported. Each port
+  should have single 'endpoint' child node. All port nodes are grouped under
+  ports node. Please refer to the bindings defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt
+
+  csi (required node)
+  Tegra210 has CSI part of VI sharing same host interface and register space.
+  So, VI device node should have CSI child node.
+
+    - csi: mipi csi interface to vi
+
+      Required properties:
+      - compatible: "nvidia,tegra210-csi"
+      - reg: Physical base address offset to parent and length of the controller
+        registers.
+      - clocks: Must contain entries csi, cilab, cilcd, cile, csi_tpg clocks.
+        See ../clocks/clock-bindings.txt for details.
+      - power-domains: Must include sor powergate node as csicil is in
+        SOR partition.
+
+      channel (optional nodes)
+      Maximum 6 channels are supported with each csi brick as either x4 or x2
+      based on hw connectivity to sensor.
+
+      Required properties:
+      - reg: csi port number. Valid port numbers are 0 through 5.
+      - nvidia,mipi-calibrate: Should contain a phandle and a specifier
+        specifying which pads are used by this CSI port and need to be
+	calibrated. See also ../display/tegra/nvidia,tegra114-mipi.txt.
+
+      Each channel node must contain 2 port nodes which can be grouped
+      under 'ports' node and each port should have a single child 'endpoint'
+      node.
+
+        ports node
+        Please refer to the bindings defined in
+        Documentation/devicetree/bindings/media/video-interfaces.txt
+
+        ports node must contain below 2 port nodes.
+        port@0 with single child 'endpoint' node always a sink.
+        port@1 with single child 'endpoint' node always a source.
+
+        port@0 (required node)
+        Required properties:
+        - reg: 0
+
+	  endpoint (required node)
+	  Required properties:
+	  - data-lanes: an array of data lane from 1 to 4. Valid array
+	    lengths are 1/2/4.
+	  - remote-endpoint: phandle to sensor 'endpoint' node.
+
+        port@1 (required node)
+        Required properties:
+        - reg: 1
+
+	  endpoint (required node)
+	  Required properties:
+	  - remote-endpoint: phandle to vi port 'endpoint' node.
+
+- epp: encoder pre-processor
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-epp"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - epp
+
+- isp: image signal processor
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-isp"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - isp
+
+- gr2d: 2D graphics engine
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-gr2d"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - 2d
+
+- gr3d: 3D graphics engine
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-gr3d"
+  - reg: Physical base address and length of the controller's registers.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    (This property may be omitted if the only clock in the list is "3d")
+    - 3d
+      This MUST be the first entry.
+    - 3d2 (Only required on SoCs with two 3D clocks)
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - 3d
+    - 3d2 (Only required on SoCs with two 3D clocks)
+
+- dc: display controller
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-dc"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - dc
+      This MUST be the first entry.
+    - parent
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - dc
+  - nvidia,head: The number of the display controller head. This is used to
+    setup the various types of output to receive video data from the given
+    head.
+
+  Each display controller node has a child node, named "rgb", that represents
+  the RGB output associated with the controller. It can take the following
+  optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+
+- hdmi: High Definition Multimedia Interface
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-hdmi"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - hdmi-supply: supply for the +5V HDMI connector pin
+  - vdd-supply: regulator for supply voltage
+  - pll-supply: regulator for PLL
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - hdmi
+      This MUST be the first entry.
+    - parent
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - hdmi
+
+  Optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+
+- tvo: TV encoder output
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-tvo"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain one entry, for the module clock.
+    See ../clocks/clock-bindings.txt for details.
+
+- dsi: display serial interface
+
+  Required properties:
+  - compatible: "nvidia,tegra<chip>-dsi"
+  - reg: Physical base address and length of the controller's registers.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - dsi
+      This MUST be the first entry.
+    - lp
+    - parent
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - dsi
+  - avdd-dsi-supply: phandle of a supply that powers the DSI controller
+  - nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying
+    which pads are used by this DSI output and need to be calibrated. See also
+    ../display/tegra/nvidia,tegra114-mipi.txt.
+
+  Optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+  - nvidia,ganged-mode: contains a phandle to a second DSI controller to gang
+    up with in order to support up to 8 data lanes
+
+- sor: serial output resource
+
+  Required properties:
+  - compatible: Should be:
+    - "nvidia,tegra124-sor": for Tegra124 and Tegra132
+    - "nvidia,tegra132-sor": for Tegra132
+    - "nvidia,tegra210-sor": for Tegra210
+    - "nvidia,tegra210-sor1": for Tegra210
+    - "nvidia,tegra186-sor": for Tegra186
+    - "nvidia,tegra186-sor1": for Tegra186
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - sor: clock input for the SOR hardware
+    - out: SOR output clock
+    - parent: input for the pixel clock
+    - dp: reference clock for the SOR clock
+    - safe: safe reference for the SOR clock during power up
+
+    For Tegra186 and later:
+    - pad: SOR pad output clock (on Tegra186 and later)
+
+    Obsolete:
+    - source: source clock for the SOR clock (obsolete, use "out" instead)
+
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - sor
+
+  Required properties on Tegra186 and later:
+  - nvidia,interface: index of the SOR interface
+
+  Optional properties:
+  - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+  - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
+  - nvidia,edid: supplies a binary EDID blob
+  - nvidia,panel: phandle of a display panel
+  - nvidia,xbar-cfg: 5 cells containing the crossbar configuration. Each lane
+    of the SOR, identified by the cell's index, is mapped via the crossbar to
+    the pad specified by the cell's value.
+
+  Optional properties when driving an eDP output:
+  - nvidia,dpaux: phandle to a DispayPort AUX interface
+
+- dpaux: DisplayPort AUX interface
+  - compatible : Should contain one of the following:
+    - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132
+    - "nvidia,tegra210-dpaux": for Tegra210
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - dpaux: clock input for the DPAUX hardware
+    - parent: reference clock
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - dpaux
+  - vdd-supply: phandle of a supply that powers the DisplayPort link
+  - i2c-bus: Subnode where I2C slave devices are listed. This subnode
+    must be always present. If there are no I2C slave devices, an empty
+    node should be added. See ../../i2c/i2c.txt for more information.
+
+  See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information
+  regarding the DPAUX pad controller bindings.
+
+- vic: Video Image Compositor
+  - compatible : "nvidia,tegra<chip>-vic"
+  - reg: Physical base address and length of the controller's registers.
+  - interrupts: The interrupt outputs from the controller.
+  - clocks: Must contain an entry for each entry in clock-names.
+    See ../clocks/clock-bindings.txt for details.
+  - clock-names: Must include the following entries:
+    - vic: clock input for the VIC hardware
+  - resets: Must contain an entry for each entry in reset-names.
+    See ../reset/reset.txt for details.
+  - reset-names: Must include the following entries:
+    - vic
+
+Example:
+
+/ {
+	...
+
+	host1x {
+		compatible = "nvidia,tegra20-host1x", "simple-bus";
+		reg = <0x50000000 0x00024000>;
+		interrupts = <0 65 0x04   /* mpcore syncpt */
+			      0 67 0x04>; /* mpcore general */
+		clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
+		resets = <&tegra_car 28>;
+		reset-names = "host1x";
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		ranges = <0x54000000 0x54000000 0x04000000>;
+
+		mpe {
+			compatible = "nvidia,tegra20-mpe";
+			reg = <0x54040000 0x00040000>;
+			interrupts = <0 68 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_MPE>;
+			resets = <&tegra_car 60>;
+			reset-names = "mpe";
+		};
+
+		vi@54080000 {
+			compatible = "nvidia,tegra210-vi";
+			reg = <0x0 0x54080000 0x0 0x700>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			assigned-clocks = <&tegra_car TEGRA210_CLK_VI>;
+			assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_C4_OUT0>;
+
+			clocks = <&tegra_car TEGRA210_CLK_VI>;
+			power-domains = <&pd_venc>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0x0 0x0 0x54080000 0x2000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					imx219_vi_in0: endpoint {
+						remote-endpoint = <&imx219_csi_out0>;
+					};
+				};
+			};
+
+			csi@838 {
+				compatible = "nvidia,tegra210-csi";
+				reg = <0x838 0x1300>;
+				assigned-clocks = <&tegra_car TEGRA210_CLK_CILAB>,
+						  <&tegra_car TEGRA210_CLK_CILCD>,
+						  <&tegra_car TEGRA210_CLK_CILE>,
+						  <&tegra_car TEGRA210_CLK_CSI_TPG>;
+				assigned-clock-parents = <&tegra_car TEGRA210_CLK_PLL_P>,
+							 <&tegra_car TEGRA210_CLK_PLL_P>,
+							 <&tegra_car TEGRA210_CLK_PLL_P>;
+				assigned-clock-rates = <102000000>,
+						       <102000000>,
+						       <102000000>,
+						       <972000000>;
+
+				clocks = <&tegra_car TEGRA210_CLK_CSI>,
+					 <&tegra_car TEGRA210_CLK_CILAB>,
+					 <&tegra_car TEGRA210_CLK_CILCD>,
+					 <&tegra_car TEGRA210_CLK_CILE>,
+					 <&tegra_car TEGRA210_CLK_CSI_TPG>;
+				clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
+				power-domains = <&pd_sor>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				channel@0 {
+					reg = <0>;
+					nvidia,mipi-calibrate = <&mipi 0x001>;
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+							imx219_csi_in0: endpoint {
+								data-lanes = <1 2>;
+								remote-endpoint = <&imx219_out0>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+							imx219_csi_out0: endpoint {
+								remote-endpoint = <&imx219_vi_in0>;
+							};
+						};
+					};
+				};
+			};
+		};
+
+		epp {
+			compatible = "nvidia,tegra20-epp";
+			reg = <0x540c0000 0x00040000>;
+			interrupts = <0 70 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_EPP>;
+			resets = <&tegra_car 19>;
+			reset-names = "epp";
+		};
+
+		isp {
+			compatible = "nvidia,tegra20-isp";
+			reg = <0x54100000 0x00040000>;
+			interrupts = <0 71 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_ISP>;
+			resets = <&tegra_car 23>;
+			reset-names = "isp";
+		};
+
+		gr2d {
+			compatible = "nvidia,tegra20-gr2d";
+			reg = <0x54140000 0x00040000>;
+			interrupts = <0 72 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_GR2D>;
+			resets = <&tegra_car 21>;
+			reset-names = "2d";
+		};
+
+		gr3d {
+			compatible = "nvidia,tegra20-gr3d";
+			reg = <0x54180000 0x00040000>;
+			clocks = <&tegra_car TEGRA20_CLK_GR3D>;
+			resets = <&tegra_car 24>;
+			reset-names = "3d";
+		};
+
+		dc@54200000 {
+			compatible = "nvidia,tegra20-dc";
+			reg = <0x54200000 0x00040000>;
+			interrupts = <0 73 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_DISP1>,
+				 <&tegra_car TEGRA20_CLK_PLL_P>;
+			clock-names = "dc", "parent";
+			resets = <&tegra_car 27>;
+			reset-names = "dc";
+
+			rgb {
+				status = "disabled";
+			};
+		};
+
+		dc@54240000 {
+			compatible = "nvidia,tegra20-dc";
+			reg = <0x54240000 0x00040000>;
+			interrupts = <0 74 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_DISP2>,
+				 <&tegra_car TEGRA20_CLK_PLL_P>;
+			clock-names = "dc", "parent";
+			resets = <&tegra_car 26>;
+			reset-names = "dc";
+
+			rgb {
+				status = "disabled";
+			};
+		};
+
+		hdmi {
+			compatible = "nvidia,tegra20-hdmi";
+			reg = <0x54280000 0x00040000>;
+			interrupts = <0 75 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_HDMI>,
+				 <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+			clock-names = "hdmi", "parent";
+			resets = <&tegra_car 51>;
+			reset-names = "hdmi";
+			status = "disabled";
+		};
+
+		tvo {
+			compatible = "nvidia,tegra20-tvo";
+			reg = <0x542c0000 0x00040000>;
+			interrupts = <0 76 0x04>;
+			clocks = <&tegra_car TEGRA20_CLK_TVO>;
+			status = "disabled";
+		};
+
+		dsi {
+			compatible = "nvidia,tegra20-dsi";
+			reg = <0x54300000 0x00040000>;
+			clocks = <&tegra_car TEGRA20_CLK_DSI>,
+				 <&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
+			clock-names = "dsi", "parent";
+			resets = <&tegra_car 48>;
+			reset-names = "dsi";
+			status = "disabled";
+		};
+	};
+
+	...
+};