Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

8 files changed, 403 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/iio/proximity/as3935.txt b/Documentation/devicetree/bindings/iio/proximity/as3935.txt
new file mode 100644
index 000000000..849115585
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/as3935.txt
@@ -0,0 +1,34 @@
+Austrian Microsystems AS3935 Franklin lightning sensor device driver
+
+Required properties:
+	- compatible: must be "ams,as3935"
+	- reg: SPI chip select number for the device
+	- spi-max-frequency: specifies maximum SPI clock frequency
+	- spi-cpha: SPI Mode 1. Refer to spi/spi-bus.txt for generic SPI
+	slave node bindings.
+	- interrupts : the sole interrupt generated by the device
+
+	Refer to interrupt-controller/interrupts.txt for generic
+	interrupt client node bindings.
+
+Optional properties:
+	- ams,tuning-capacitor-pf: Calibration tuning capacitor stepping
+	  value 0 - 120pF. This will require using the calibration data from
+	  the manufacturer.
+	- ams,nflwdth: Set the noise and watchdog threshold register on
+	  startup. This will need to set according to the noise from the
+	  MCU board, and possibly the local environment. Refer to the
+	  datasheet for the threshold settings.
+
+Example:
+
+as3935@0 {
+	compatible = "ams,as3935";
+	reg = <0>;
+	spi-max-frequency = <400000>;
+	spi-cpha;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 1>;
+	ams,tuning-capacitor-pf = <80>;
+	ams,nflwdth = <0x44>;
+};
diff --git a/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml b/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml
new file mode 100644
index 000000000..ce7952798
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/devantech-srf04.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Devantech SRF04 and Maxbotix mb1000 ultrasonic range finder
+
+maintainers:
+  - Andreas Klinger <ak@it-klinger.de>
+
+description: |
+  Bit-banging driver using two GPIOs:
+  - trigger-gpio is raised by the driver to start sending out an ultrasonic
+    burst
+  - echo-gpio is held high by the sensor after sending ultrasonic burst
+    until it is received once again
+
+  Specifications about the devices can be found at:
+  https://www.robot-electronics.co.uk/htm/srf04tech.htm
+
+  https://www.maxbotix.com/documents/LV-MaxSonar-EZ_Datasheet.pdf
+
+properties:
+  compatible:
+    enum:
+      - devantech,srf04
+      - maxbotix,mb1000
+      - maxbotix,mb1010
+      - maxbotix,mb1020
+      - maxbotix,mb1030
+      - maxbotix,mb1040
+
+  trig-gpios:
+    description:
+      Definition of the GPIO for the triggering (output)
+      This GPIO is set for about 10 us by the driver to tell the device it
+      should initiate the measurement cycle.
+      See Documentation/devicetree/bindings/gpio/gpio.txt for information
+      on how to specify a consumer gpio.
+    maxItems: 1
+
+  echo-gpios:
+    description:
+      Definition of the GPIO for the echo (input)
+      This GPIO is set by the device as soon as an ultrasonic burst is sent
+      out and reset when the first echo is received.
+      Thus this GPIO is set while the ultrasonic waves are doing one round
+      trip.
+      It needs to be an GPIO which is able to deliver an interrupt because
+      the time between two interrupts is measured in the driver.
+    maxItems: 1
+
+  power-gpios:
+    description:
+      Definition of the GPIO for power management of connected peripheral
+      (output).
+      This GPIO can be used by the external hardware for power management.
+      When the device gets suspended it's switched off and when it resumes
+      it's switched on again. After some period of inactivity the driver
+      get suspended automatically (autosuspend feature).
+    maxItems: 1
+
+  startup-time-ms:
+    description:
+      This is the startup time the device needs after a resume to be up and
+      running.
+    minimum: 0
+    maximum: 1000
+    default: 100
+
+required:
+  - compatible
+  - trig-gpios
+  - echo-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    proximity {
+        compatible = "devantech,srf04";
+        trig-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+        echo-gpios = <&gpio2  6 GPIO_ACTIVE_HIGH>;
+    };
diff --git a/Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.yaml b/Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.yaml
new file mode 100644
index 000000000..3eac248f2
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/maxbotix,mb1232.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/maxbotix,mb1232.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MaxBotix I2CXL-MaxSonar ultrasonic distance sensor
+
+maintainers:
+  - Andreas Klinger <ak@it-klinger.de>
+
+description: |
+  MaxBotix I2CXL-MaxSonar ultrasonic distance sensor of type  mb1202,
+  mb1212, mb1222, mb1232, mb1242, mb7040 or mb7137 using the i2c interface
+  for ranging
+
+  Specifications about the devices can be found at:
+  https://www.maxbotix.com/documents/I2CXL-MaxSonar-EZ_Datasheet.pdf
+
+properties:
+  compatible:
+    enum:
+      - maxbotix,mb1202
+      - maxbotix,mb1212
+      - maxbotix,mb1222
+      - maxbotix,mb1232
+      - maxbotix,mb1242
+      - maxbotix,mb7040
+      - maxbotix,mb7137
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    description:
+      Interrupt used to announce the preceding reading request has finished
+      and that data is available.  If no interrupt is specified the device
+      driver falls back to wait a fixed amount of time until data can be
+      retrieved.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      proximity@70 {
+        compatible = "maxbotix,mb1232";
+        reg = <0x70>;
+        interrupt-parent = <&gpio2>;
+        interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/iio/proximity/parallax-ping.yaml b/Documentation/devicetree/bindings/iio/proximity/parallax-ping.yaml
new file mode 100644
index 000000000..ada55f186
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/parallax-ping.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/parallax-ping.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Parallax PING))) and LaserPING range finder
+
+maintainers:
+  - Andreas Klinger <ak@it-klinger.de>
+
+description: |
+  Bit-banging driver using one GPIO:
+  - ping-gpios is raised by the driver to start measurement
+  - direction of ping-gpio is then switched into input with an interrupt
+    for receiving distance value as PWM signal
+
+  Specifications about the devices can be found at:
+  http://parallax.com/sites/default/files/downloads/28041-LaserPING-2m-Rangefinder-Guide.pdf
+  http://parallax.com/sites/default/files/downloads/28015-PING-Documentation-v1.6.pdf
+
+properties:
+  compatible:
+    enum:
+      - parallax,ping
+      - parallax,laserping
+
+  ping-gpios:
+    description:
+      Definition of the GPIO for the triggering and echo (output and input)
+      This GPIO is set for about 5 us by the driver to tell the device it
+      should initiate the measurement cycle. Afterwards the GPIO is switched
+      to input direction with an interrupt. The device sets it and the
+      length of the input signal corresponds to the measured distance.
+      It needs to be an GPIO which is able to deliver an interrupt because
+      the time between two interrupts is measured in the driver.
+      See Documentation/devicetree/bindings/gpio/gpio.txt for information
+      on how to specify a consumer gpio.
+    maxItems: 1
+
+required:
+  - compatible
+  - ping-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    proximity {
+        compatible = "parallax,laserping";
+        ping-gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+    };
diff --git a/Documentation/devicetree/bindings/iio/proximity/semtech,sx9310.yaml b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9310.yaml
new file mode 100644
index 000000000..5739074d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/semtech,sx9310.yaml
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/semtech,sx9310.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Semtech's SX9310 capacitive proximity sensor
+
+maintainers:
+  - Daniel Campello <campello@chromium.org>
+
+description: |
+  Semtech's SX9310/SX9311 capacitive proximity/button solution.
+
+  Specifications about the devices can be found at:
+  https://www.semtech.com/products/smart-sensing/sar-sensors/sx9310
+
+properties:
+  compatible:
+    enum:
+      - semtech,sx9310
+      - semtech,sx9311
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    description:
+      The sole interrupt generated by the device used to announce the
+      preceding reading request has finished and that data is
+      available or that a close/far proximity event has happened.
+    maxItems: 1
+
+  vdd-supply:
+    description: Main power supply
+
+  svdd-supply:
+    description: Host interface power supply
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - "#io-channel-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      proximity@28 {
+        compatible = "semtech,sx9310";
+        reg = <0x28>;
+        interrupt-parent = <&pio>;
+        interrupts = <5 IRQ_TYPE_LEVEL_LOW 5>;
+        vdd-supply = <&pp3300_a>;
+        svdd-supply = <&pp1800_prox>;
+        #io-channel-cells = <1>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/iio/proximity/sx9500.txt b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt
new file mode 100644
index 000000000..c54455db3
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/sx9500.txt
@@ -0,0 +1,23 @@
+Semtech's SX9500 capacitive proximity button device driver
+
+Required properties:
+	- compatible: must be "semtech,sx9500"
+	- reg: i2c address where to find the device
+	- interrupts : the sole interrupt generated by the device
+
+	Refer to interrupt-controller/interrupts.txt for generic
+	interrupt client node bindings.
+
+Optional properties:
+	- reset-gpios: Reference to the GPIO connected to the device's active
+	  low reset pin.
+
+Example:
+
+sx9500@28 {
+	compatible = "semtech,sx9500";
+	reg = <0x28>;
+	interrupt-parent = <&gpio2>;
+	interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+	reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+};
diff --git a/Documentation/devicetree/bindings/iio/proximity/vishay,vcnl3020.yaml b/Documentation/devicetree/bindings/iio/proximity/vishay,vcnl3020.yaml
new file mode 100644
index 000000000..fbd3a2e32
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/vishay,vcnl3020.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/vishay,vcnl3020.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Integrated Proximity Sensor With Infrared Emitter
+
+maintainers:
+  - Ivan Mikhaylov <i.mikhaylov@yadro.com>
+
+description: |
+  The VCNL3020 is a fully integrated proximity sensor. Fully integrated means
+  that the infrared emitter is included in the package. It has 16-bit
+  resolution. It includes a signal processing IC and features standard I2C
+  communication interface. It features an interrupt function.
+
+  Specifications about the devices can be found at:
+  https://www.vishay.com/docs/84150/vcnl3020.pdf
+
+properties:
+  compatible:
+    enum:
+      - vishay,vcnl3020
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  vdd-supply:
+    description: Regulator that provides power to the sensor
+
+  vddio-supply:
+    description: Regulator that provides power to the bus
+
+  vishay,led-current-microamp:
+    description:
+      The driver current for the LED used in proximity sensing.
+    enum: [0, 10000, 20000, 30000, 40000, 50000, 60000, 70000, 80000, 90000,
+           100000, 110000, 120000, 130000, 140000, 150000, 160000, 170000,
+           180000, 190000, 200000]
+    default: 20000
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        proximity@13 {
+              compatible = "vishay,vcnl3020";
+              reg = <0x13>;
+              vishay,led-current-microamp = <200000>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt b/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt
new file mode 100644
index 000000000..dfe00eb96
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/vl53l0x.txt
@@ -0,0 +1,18 @@
+ST VL53L0X ToF ranging sensor
+
+Required properties:
+	- compatible: must be "st,vl53l0x"
+	- reg: i2c address where to find the device
+
+Optional properties:
+	- interrupts:	Interrupt for notifying that new measurement is ready.
+			If no interrupt is specified, polling is used.
+
+Example:
+
+vl53l0x@29 {
+	compatible = "st,vl53l0x";
+	reg = <0x29>;
+	interrupt-parent = <&gpio>;
+	interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+};