Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 88 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
new file mode 100644
index 000000000..b3e688b77
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
@@ -0,0 +1,88 @@
+* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
+
+The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
+HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
+input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
+similar to the 7611 but has 2 HDMI inputs.
+
+These device tree bindings support the ADV7611/12 only at the moment.
+
+Required Properties:
+
+  - compatible: Must contain one of the following
+    - "adi,adv7611" for the ADV7611
+    - "adi,adv7612" for the ADV7612
+
+  - reg: I2C slave addresses
+    The ADV76xx has up to thirteen 256-byte maps that can be accessed via the
+    main I2C ports. Each map has it own I2C address and acts as a standard
+    slave device on the I2C bus. The main address is mandatory, others are
+    optional and revert to defaults if not specified.
+
+  - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
+    detection pins, one per HDMI input. The active flag indicates the GPIO
+    level that enables hot-plug detection.
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+  Port			ADV7611    ADV7612
+------------------------------------------------------------
+  HDMI			0             0, 1
+  Digital output	1                2
+
+The digital output port node must contain at least one endpoint.
+
+Optional Properties:
+
+  - reset-gpios: Reference to the GPIO connected to the device's reset pin.
+  - default-input: Select which input is selected after reset.
+  - reg-names : Names of maps with programmable addresses.
+		It can contain any map needing a non-default address.
+		Possible maps names are :
+		  "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe",
+		  "rep", "edid", "hdmi", "test", "cp", "vdp"
+
+Optional Endpoint Properties:
+
+  The following three properties are defined in video-interfaces.txt and are
+  valid for source endpoints only.
+
+  - hsync-active: Horizontal synchronization polarity. Defaults to active low.
+  - vsync-active: Vertical synchronization polarity. Defaults to active low.
+  - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
+
+  If none of hsync-active, vsync-active and pclk-sample is specified the
+  endpoint will use embedded BT.656 synchronization.
+
+Example:
+
+	hdmi_receiver@4c {
+		compatible = "adi,adv7611";
+		/*
+		 * The edid page will be accessible @ 0x66 on the I2C bus. All
+		 * other maps will retain their default addresses.
+		 */
+		reg = <0x4c>, <0x66>;
+		reg-names = "main", "edid";
+
+		reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+		hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		default-input = <0>;
+
+		port@0 {
+			reg = <0>;
+		};
+		port@1 {
+			reg = <1>;
+			hdmi_in: endpoint {
+				remote-endpoint = <&ccdc_in>;
+			};
+		};
+	};