Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 157 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
new file mode 100644
index 000000000..719b2995d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -0,0 +1,157 @@
+* Texas Instruments TVP5150 and TVP5151 video decoders
+
+The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
+(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
+with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
+
+Required Properties:
+====================
+- compatible:	Value must be "ti,tvp5150".
+- reg:		I2C slave address.
+
+Optional Properties:
+====================
+- pdn-gpios:	Phandle for the GPIO connected to the PDN pin, if any.
+- reset-gpios:	Phandle for the GPIO connected to the RESETB pin, if any.
+
+The device node must contain one 'port' child node per device physical input
+and output port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows
+
+	  Name		Type		Port
+	--------------------------------------
+	  AIP1A		sink		0
+	  AIP1B		sink		1
+	  Y-OUT		src		2
+
+The device node must contain at least one sink port and the src port. Each input
+port must be linked to an endpoint defined in [1]. The port/connector layout is
+as follows
+
+tvp-5150 port@0 (AIP1A)
+	endpoint@0 -----------> Comp0-Con  port
+	endpoint@1 ------+----> Svideo-Con port
+tvp-5150 port@1 (AIP1B)  |
+	endpoint@1 ------+
+	endpoint@0 -----------> Comp1-Con  port
+tvp-5150 port@2
+	endpoint (video bitstream output at YOUT[0-7] parallel bus)
+
+Required Endpoint Properties for parallel synchronization on output port:
+=========================================================================
+
+- hsync-active:		Active state of the HSYNC signal. Must be <1> (HIGH).
+- vsync-active:		Active state of the VSYNC signal. Must be <1> (HIGH).
+- field-even-active:	Field signal level during the even field data
+			transmission. Must be <0>.
+
+Note: Do not specify any of these properties if you want to use the embedded
+      BT.656 synchronization.
+
+Optional Connector Properties:
+==============================
+
+- sdtv-standards: Set the possible signals to which the hardware tries to lock
+                  instead of using the autodetection mechnism. Please look at
+                  [1] for more information.
+
+[1] Documentation/devicetree/bindings/display/connector/analog-tv-connector.yaml.
+
+Example - three input sources:
+#include <dt-bindings/display/sdtv-standards.h>
+
+comp_connector_0 {
+	compatible = "composite-video-connector";
+	label = "Composite0";
+	sdtv-standards = <SDTV_STD_PAL_M>; /* limit to pal-m signals */
+
+	port {
+		composite0_to_tvp5150: endpoint {
+			remote-endpoint = <&tvp5150_to_composite0>;
+		};
+	};
+};
+
+comp_connector_1 {
+	compatible = "composite-video-connector";
+	label = "Composite1";
+	sdtv-standards = <SDTV_STD_NTSC_M>; /* limit to ntsc-m signals */
+
+	port {
+		composite1_to_tvp5150: endpoint {
+			remote-endpoint = <&tvp5150_to_composite1>;
+		};
+	};
+};
+
+svideo_connector {
+	compatible = "svideo-connector";
+	label = "S-Video";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		svideo_luma_to_tvp5150: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&tvp5150_to_svideo_luma>;
+		};
+
+		svideo_chroma_to_tvp5150: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&tvp5150_to_svideo_chroma>;
+		};
+	};
+};
+
+&i2c2 {
+	tvp5150@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			tvp5150_to_composite0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&composite0_to_tvp5150>;
+			};
+
+			tvp5150_to_svideo_luma: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&svideo_luma_to_tvp5150>;
+			};
+		};
+
+		port@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			tvp5150_to_composite1: endpoint@0 {
+				reg = <0>;
+                                remote-endpoint = <&composite1_to_tvp5150>;
+			};
+
+			tvp5150_to_svideo_chroma: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&svideo_chroma_to_tvp5150>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			tvp5150_1: endpoint {
+				remote-endpoint = <&ccdc_ep>;
+			};
+		};
+	};
+};