diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt | |
parent | Initial commit. (diff) | |
download | linux-upstream/5.10.209.tar.xz linux-upstream/5.10.209.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
-rw-r--r-- | Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt | 88 |
1 files changed, 88 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt new file mode 100644 index 000000000..880d4d70c --- /dev/null +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt @@ -0,0 +1,88 @@ +STMicroelectronics STi c8sectpfe binding +============================================ + +This document describes the c8sectpfe device bindings that is used to get transport +stream data into the SoC on the TS pins, and into DDR for further processing. + +It is typically used in conjunction with one or more demodulator and tuner devices +which converts from the RF to digital domain. Demodulators and tuners are usually +located on an external DVB frontend card connected to SoC TS input pins. + +Currently 7 TS input (tsin) channels are supported on the stih407 family SoC. + +Required properties (controller (parent) node): +- compatible : Should be "stih407-c8sectpfe" + +- reg : Address and length of register sets for each device in + "reg-names" + +- reg-names : The names of the register addresses corresponding to the + registers filled in "reg": + - c8sectpfe: c8sectpfe registers + - c8sectpfe-ram: c8sectpfe internal sram + +- clocks : phandle list of c8sectpfe clocks +- clock-names : should be "c8sectpfe" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +- pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num) + must be defined for each tsin child node. +- pinctrl-0 : phandle referencing pin configuration for this tsin configuration +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + + +Required properties (tsin (child) node): + +- tsin-num : tsin id of the InputBlock (must be between 0 to 6) +- i2c-bus : phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected. +- reset-gpios : reset gpio for this tsin channel. + +Optional properties (tsin (child) node): + +- invert-ts-clk : Bool property to control sense of ts input clock (data stored on falling edge of clk). +- serial-not-parallel : Bool property to configure input bus width (serial on ts_data<7>). +- async-not-sync : Bool property to control if data is received in asynchronous mode + (all bits/bytes with ts_valid or ts_packet asserted are valid). + +- dvb-card : Describes the NIM card connected to this tsin channel. + +Example: + +/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */ + + c8sectpfe@8a20000 { + compatible = "st,stih407-c8sectpfe"; + reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>; + reg-names = "stfe", "stfe-ram"; + interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>; + interrupt-names = "stfe-error-irq", "stfe-idle-irq"; + pinctrl-0 = <&pinctrl_tsin0_serial>; + pinctrl-1 = <&pinctrl_tsin0_parallel>; + pinctrl-2 = <&pinctrl_tsin3_serial>; + pinctrl-3 = <&pinctrl_tsin4_serial_alt3>; + pinctrl-4 = <&pinctrl_tsin5_serial_alt1>; + pinctrl-names = "tsin0-serial", + "tsin0-parallel", + "tsin3-serial", + "tsin4-serial", + "tsin5-serial"; + clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>; + clock-names = "c8sectpfe"; + + /* tsin0 is TSA on NIMA */ + tsin0: port@0 { + tsin-num = <0>; + serial-not-parallel; + i2c-bus = <&ssc2>; + reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>; + dvb-card = <STV0367_TDA18212_NIMA_1>; + }; + + tsin3: port@3 { + tsin-num = <3>; + serial-not-parallel; + i2c-bus = <&ssc3>; + reset-gpios = <&pio15 7 GPIO_ACTIVE_HIGH>; + dvb-card = <STV0367_TDA18212_NIMB_1>; + }; + }; |