diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/memory-controllers/ti | |
parent | Initial commit. (diff) | |
download | linux-upstream/5.10.209.tar.xz linux-upstream/5.10.209.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
3 files changed, 314 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt new file mode 100644 index 000000000..190437a0c --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt @@ -0,0 +1,210 @@ +* Device tree bindings for Texas instruments AEMIF controller + +The Async External Memory Interface (EMIF16/AEMIF) controller is intended to +provide a glue-less interface to a variety of asynchronous memory devices like +ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories +can be accessed at any given time via four chip selects with 64M byte access +per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM +and Mobile SDR are not supported. + +Documentation: +Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf +Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf + +Required properties: + +- compatible: "ti,davinci-aemif" + "ti,keystone-aemif" + "ti,da850-aemif" + +- reg: contains offset/length value for AEMIF control registers + space. + +- #address-cells: Must be 2. The partition number has to be encoded in the + first address cell and it may accept values 0..N-1 + (N - total number of partitions). It's recommended to + assign N-1 number for the control partition. The second + cell is the offset into the partition. + +- #size-cells: Must be set to 1. + +- ranges: Contains memory regions. There are two types of + ranges/partitions: + - CS-specific partition/range. If continuous, must be + set up to reflect the memory layout for 4 chipselects, + if not then additional range/partition can be added and + child device can select the proper one. + - control partition which is common for all CS + interfaces. + +- clocks: the clock feeding the controller clock. Required only + if clock tree data present in device tree. + See clock-bindings.txt + +- clock-names: clock name. It has to be "aemif". Required only if clock + tree data present in device tree, in another case don't + use it. + See clock-bindings.txt + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + See clock-bindings.txt + + +Child chip-select (cs) nodes contain the memory devices nodes connected to +such as NOR (e.g. cfi-flash) and NAND (ti,davinci-nand, see davinci-nand.txt). +There might be board specific devices like FPGAs. + +Required child cs node properties: + +- #address-cells: Must be 2. + +- #size-cells: Must be 1. + +- ranges: Empty property indicating that child nodes can inherit + memory layout. + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + +- ti,cs-chipselect: number of chipselect. Indicates on the aemif driver + which chipselect is used for accessing the memory. For + compatibles "ti,davinci-aemif" and "ti,keystone-aemif" + it can be in range [0-3]. For compatible + "ti,da850-aemif" range is [2-5]. + +Optional child cs node properties: + +- ti,cs-bus-width: width of the asynchronous device's data bus + 8 or 16 if not preset 8 + +- ti,cs-select-strobe-mode: enable/disable select strobe mode + In select strobe mode chip select behaves as + the strobe and is active only during the strobe + period. If present then enable. + +- ti,cs-extended-wait-mode: enable/disable extended wait mode + if set, the controller monitors the EMIFWAIT pin + mapped to that chip select to determine if the + device wants to extend the strobe period. If + present then enable. + +- ti,cs-min-turnaround-ns: minimum turn around time, ns + Time between the end of one asynchronous memory + access and the start of another asynchronous + memory access. This delay is not incurred + between a read followed by read or a write + followed by a write to same chip select. + +- ti,cs-read-setup-ns: read setup width, ns + Time between the beginning of a memory cycle + and the activation of read strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-read-strobe-ns: read strobe width, ns + Time between the activation and deactivation of + the read strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-read-hold-ns: read hold width, ns + Time between the deactivation of the read + strobe and the end of the cycle (which may be + either an address change or the deactivation of + the chip select signal. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-setup-ns: write setup width, ns + Time between the beginning of a memory cycle + and the activation of write strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-strobe-ns: write strobe width, ns + Time between the activation and deactivation of + the write strobe. + Minimum value is 1 (0 treated as 1). + +- ti,cs-write-hold-ns: write hold width, ns + Time between the deactivation of the write + strobe and the end of the cycle (which may be + either an address change or the deactivation of + the chip select signal. + Minimum value is 1 (0 treated as 1). + +If any of the above parameters are absent, current parameter value will be taken +from the corresponding HW reg. + +Example for aemif, davinci nand and nor flash chip select shown below. + +memory-controller@21000a00 { + compatible = "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&clkaemif 0>; + clock-names = "aemif"; + clock-ranges; + reg = <0x21000A00 0x00000100>; + ranges = <0 0 0x70000000 0x10000000 + 1 0 0x21000A00 0x00000100>; + /* + * Partition0: CS-specific memory range which is + * implemented as continuous physical memory region + * Partition1: control memory range + */ + + nand:cs2 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <2>; + /* all timings in nanoseconds */ + ti,cs-min-turnaround-ns = <0>; + ti,cs-read-hold-ns = <7>; + ti,cs-read-strobe-ns = <42>; + ti,cs-read-setup-ns = <14>; + ti,cs-write-hold-ns = <7>; + ti,cs-write-strobe-ns = <42>; + ti,cs-write-setup-ns = <14>; + + nand@0,0x8000000 { + compatible = "ti,davinci-nand"; + reg = <0 0x8000000 0x4000000 + 1 0x0000000 0x0000100>; + /* + * Partition0, offset 0x8000000, size 0x4000000 + * Partition1, offset 0x0000000, size 0x0000100 + */ + + .. see davinci-nand.txt + }; + }; + + nor:cs0 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <0>; + /* all timings in nanoseconds */ + ti,cs-min-turnaround-ns = <0>; + ti,cs-read-hold-ns = <8>; + ti,cs-read-strobe-ns = <40>; + ti,cs-read-setup-ns = <14>; + ti,cs-write-hold-ns = <7>; + ti,cs-write-strobe-ns = <40>; + ti,cs-write-setup-ns = <14>; + ti,cs-bus-width = <16>; + + flash@0,0x0000000 { + compatible = "cfi-flash"; + reg = <0 0x0000000 0x4000000>; + + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt new file mode 100644 index 000000000..ec1dd408d --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments da8xx DDR2/mDDR memory controller + +The DDR2/mDDR memory controller present on Texas Instruments da8xx SoCs features +a set of registers which allow to tweak the controller's behavior. + +Documentation: +OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf + +Required properties: + +- compatible: "ti,da850-ddr-controller" - for da850 SoC based boards +- reg: a tuple containing the base address of the memory + controller and the size of the memory area to map + +Example for da850 shown below. + +ddrctl { + compatible = "ti,da850-ddr-controller"; + reg = <0xb0000000 0xe8>; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt new file mode 100644 index 000000000..63f674ffe --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -0,0 +1,84 @@ +* EMIF family of TI SDRAM controllers + +EMIF - External Memory Interface - is an SDRAM controller used in +TI SoCs. EMIF supports, based on the IP revision, one or more of +DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance +of the EMIF IP and memory parts attached to it. Certain revisions +of the EMIF controller also contain optional ECC support, which +corrects one bit errors and detects two bit errors. + +Required properties: +- compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> + is the IP revision of the specific EMIF instance. For newer controllers, + compatible should be one of the following: + "ti,emif-am3352" + "ti,emif-am4372" + "ti,emif-dra7xx" + "ti,emif-keystone" + +- phy-type : <u32> indicating the DDR phy type. Following are the + allowed values + <1> : Attila PHY + <2> : Intelli PHY + +- device-handle : phandle to a "lpddr2" node representing the memory part + +- ti,hwmods : For TI hwmods processing and omap device creation + the value shall be "emif<n>" where <n> is the number of the EMIF + instance with base 1. +- interrupts : interrupt used by the controller + +Required only for "ti,emif-am3352" and "ti,emif-am4372": +- sram : Phandles for generic sram driver nodes, + first should be type 'protect-exec' for the driver to use to copy + and run PM functions, second should be regular pool to be used for + data region for code. See Documentation/devicetree/bindings/sram/sram.yaml + for more details. + +Optional properties: +- cs1-used : Have this property if CS1 of this EMIF + instance has a memory part attached to it. If there is a memory + part attached to CS1, it should be the same type as the one on CS0, + so there is no need to give the details of this memory part. + +- cal-resistor-per-cs : Have this property if the board has one + calibration resistor per chip-select. + +- hw-caps-read-idle-ctrl: Have this property if the controller + supports read idle window programming + +- hw-caps-dll-calib-ctrl: Have this property if the controller + supports dll calibration control + +- hw-caps-ll-interface : Have this property if the controller + has a low latency interface and corresponding interrupt events + +- hw-caps-temp-alert : Have this property if the controller + has capability for generating SDRAM temperature alerts + +-Examples: + +emif1: emif@4c000000 { + compatible = "ti,emif-4d"; + ti,hwmods = "emif2"; + phy-type = <1>; + device-handle = <&elpida_ECB240ABACN>; + cs1-used; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; +}; + +/* From am33xx.dtsi */ +emif: emif@4c000000 { + compatible = "ti,emif-am3352"; + reg = <0x4C000000 0x1000>; + sram = <&pm_sram_code + &pm_sram_data>; +}; + +emif1: emif@4c000000 { + compatible = "ti,emif-dra7xx"; + reg = <0x4c000000 0x200>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; +}; |