diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/mfd/max77693.txt | |
parent | Initial commit. (diff) | |
download | linux-430c2fc249ea5c0536abd21c23382884005c9093.tar.xz linux-430c2fc249ea5c0536abd21c23382884005c9093.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/max77693.txt')
-rw-r--r-- | Documentation/devicetree/bindings/mfd/max77693.txt | 194 |
1 files changed, 194 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt new file mode 100644 index 000000000..0ced96e16 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -0,0 +1,194 @@ +Maxim MAX77693 multi-function device + +MAX77693 is a Multifunction device with the following submodules: +- PMIC, +- CHARGER, +- LED, +- MUIC, +- HAPTIC + +It is interfaced to host controller using i2c. +This document describes the bindings for the mfd device. + +Required properties: +- compatible : Must be "maxim,max77693". +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. + +Optional properties: +- regulators : The regulators of max77693 have to be instantiated under subnode + named "regulators" using the following format. + + regulators { + regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constraints[*]. + }; + + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + +- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide + users with tactile feedback. PWM period and duty-cycle are varied in + order to provide the appropriate level of feedback. + + Required properties: + - compatible : Must be "maxim,max77693-haptic" + - haptic-supply : power supply for the haptic motor + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + - pwms : phandle to the physical PWM(Pulse Width Modulation) device. + PWM properties should be named "pwms". And number of cell is different + for each pwm device. + To get more information, please refer to documentation. + [*] refer Documentation/devicetree/bindings/pwm/pwm.txt + +- charger : Node configuring the charger driver. + If present, required properties: + - compatible : Must be "maxim,max77693-charger". + + Optional properties (if not set, defaults will be used): + - maxim,constant-microvolt : Battery constant voltage in uV. The charger + will operate in fast charge constant current mode till battery voltage + reaches this level. Then the charger will switch to fast charge constant + voltage mode. Also vsys (system voltage) will be set to this value when + DC power is supplied but charger is not enabled. + Valid values: 3650000 - 4400000, step by 25000 (rounded down) + Default: 4200000 + + - maxim,min-system-microvolt : Minimal system voltage in uV. + Valid values: 3000000 - 3700000, step by 100000 (rounded down) + Default: 3600000 + + - maxim,thermal-regulation-celsius : Temperature in Celsius for entering + high temperature charging mode. If die temperature exceeds this value + the charging current will be reduced by 105 mA/Celsius. + Valid values: 70, 85, 100, 115 + Default: 100 + + - maxim,battery-overcurrent-microamp : Overcurrent protection threshold + in uA (current from battery to system). + Valid values: 2000000 - 3500000, step by 250000 (rounded down) + Default: 3500000 + + - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for + triggering input voltage regulation loop. If input voltage decreases + below this value, the input current will be reduced to reach the + threshold voltage. + Valid values: 4300000, 4700000, 4800000, 4900000 + Default: 4300000 + +- led : the LED submodule device node + +There are two LED outputs available - FLED1 and FLED2. Each of them can +control a separate LED or they can be connected together to double +the maximum current for a single connected LED. One LED is represented +by one child node. + +Required properties: +- compatible : Must be "maxim,max77693-led". + +Optional properties: +- maxim,boost-mode : + In boost mode the device can produce up to 1.2A of total current + on both outputs. The maximum current on each output is reduced + to 625mA then. If not enabled explicitly, boost setting defaults to + LEDS_BOOST_FIXED in case both current sources are used. + Possible values: + LEDS_BOOST_OFF (0) - no boost, + LEDS_BOOST_ADAPTIVE (1) - adaptive mode, + LEDS_BOOST_FIXED (2) - fixed mode. +- maxim,boost-mvout : Output voltage of the boost module in millivolts. + Valid values: 3300 - 5500, step by 25 (rounded down) + Default: 3300 +- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired + if chip estimates that system voltage could drop below this level due + to flash power consumption. + Valid values: 2400 - 3400, step by 33 (rounded down) + Default: 2400 + +Required properties for the LED child node: +- led-sources : see Documentation/devicetree/bindings/leds/common.txt; + device current output identifiers: 0 - FLED1, 1 - FLED2 +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + Valid values for a LED connected to one FLED output: + 15625 - 250000, step by 15625 (rounded down) + Valid values for a LED connected to both FLED outputs: + 15625 - 500000, step by 15625 (rounded down) +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + Valid values for a single LED connected to one FLED output + (boost mode must be turned off): + 15625 - 1000000, step by 15625 (rounded down) + Valid values for a single LED connected to both FLED outputs: + 15625 - 1250000, step by 15625 (rounded down) + Valid values for two LEDs case: + 15625 - 625000, step by 15625 (rounded down) +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt + Valid values: 62500 - 1000000, step by 62500 (rounded down) + +Optional properties for the LED child node: +- label : see Documentation/devicetree/bindings/leds/common.txt + +Optional nodes: +- max77693-muic : + Node used only by extcon consumers. + Required properties: + - compatible : "maxim,max77693-muic" + +Example: +#include <dt-bindings/leds/common.h> + + max77693@66 { + compatible = "maxim,max77693"; + reg = <0x66>; + interrupt-parent = <&gpx1>; + interrupts = <5 2>; + + regulators { + esafeout@1 { + regulator-compatible = "ESAFEOUT1"; + regulator-name = "ESAFEOUT1"; + regulator-boot-on; + }; + esafeout@2 { + regulator-compatible = "ESAFEOUT2"; + regulator-name = "ESAFEOUT2"; + }; + charger@0 { + regulator-compatible = "CHARGER"; + regulator-name = "CHARGER"; + regulator-min-microamp = <60000>; + regulator-max-microamp = <2580000>; + regulator-boot-on; + }; + }; + + haptic { + compatible = "maxim,max77693-haptic"; + haptic-supply = <&haptic_supply>; + pwms = <&pwm 0 40000 0>; + pwm-names = "haptic"; + }; + + charger { + compatible = "maxim,max77693-charger"; + + maxim,constant-microvolt = <4200000>; + maxim,min-system-microvolt = <3600000>; + maxim,thermal-regulation-celsius = <75>; + maxim,battery-overcurrent-microamp = <3000000>; + maxim,charge-input-threshold-microvolt = <4300000>; + }; + + led { + compatible = "maxim,max77693-led"; + maxim,boost-mode = <LEDS_BOOST_FIXED>; + maxim,boost-mvout = <5000>; + maxim,mvsys-min = <2400>; + + camera_flash: flash-led { + label = "max77693-flash"; + led-sources = <0>, <1>; + led-max-microamp = <500000>; + flash-max-microamp = <1250000>; + flash-max-timeout-us = <1000000>; + }; + }; + }; |