diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/net/fsl-fec.txt | |
parent | Initial commit. (diff) | |
download | linux-upstream.tar.xz linux-upstream.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
-rw-r--r-- | Documentation/devicetree/bindings/net/fsl-fec.txt | 95 |
1 files changed, 95 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt new file mode 100644 index 000000000..9b543789c --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -0,0 +1,95 @@ +* Freescale Fast Ethernet Controller (FEC) + +Required properties: +- compatible : Should be "fsl,<soc>-fec" +- reg : Address and length of the register set for the device +- interrupts : Should contain fec interrupt +- phy-mode : See ethernet.txt file in the same directory + +Optional properties: +- phy-supply : regulator that powers the Ethernet PHY. +- phy-handle : phandle to the PHY device connected to this device. +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. +- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the tx queue number, otherwise set tx queue + number to 1. +- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the rx queue number, otherwise set rx queue + number to 1. +- fsl,magic-packet : If present, indicates that the hardware supports waking + up via magic packet. +- fsl,err006687-workaround-present: If present indicates that the system has + the hardware workaround for ERR006687 applied and does not need a software + workaround. +- fsl,stop-mode: register bits of stop mode control, the format is + <&gpr req_gpr req_bit>. + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset for ENET stop request. + req_bit is the gpr bit offset for ENET stop request. + -interrupt-names: names of the interrupts listed in interrupts property in + the same order. The defaults if not specified are + __Number of interrupts__ __Default__ + 1 "int0" + 2 "int0", "pps" + 3 "int0", "int1", "int2" + 4 "int0", "int1", "int2", "pps" + The order may be changed as long as they correspond to the interrupts + property. Currently, only i.mx7 uses "int1" and "int2". They correspond to + tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts. + For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse + per second interrupt associated with 1588 precision time protocol(PTP). + +Optional subnodes: +- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes + according to phy.txt in the same directory + +Deprecated optional properties: + To avoid these, create a phy node according to phy.txt in the same + directory, and point the fec's "phy-handle" property to it. Then use + the phy's reset binding, again described by phy.txt. +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. +- phy-reset-active-high : If present then the reset sequence using the GPIO + specified in the "phy-reset-gpios" property is reversed (H=reset state, + L=operation state). +- phy-reset-post-delay : Post reset delay in milliseconds. If present then + a delay of phy-reset-post-delay milliseconds will be observed after the + phy-reset-gpios has been toggled. Can be omitted thus no delay is + observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. + +Example: + +ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; + phy-supply = <®_fec_supply>; +}; + +Example with phy specified: + +ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; + phy-supply = <®_fec_supply>; + phy-handle = <ðphy>; + mdio { + clock-frequency = <5000000>; + ethphy: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <6>; + max-speed = <100>; + }; + }; +}; |