Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 82 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt b/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt
new file mode 100644
index 000000000..534e38058
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio-mux-multiplexer.txt
@@ -0,0 +1,82 @@
+Properties for an MDIO bus multiplexer consumer device
+
+This is a special case of MDIO mux  when MDIO mux is defined as a consumer
+of a mux producer device. The mux producer can be of any type like mmio mux
+producer, gpio mux producer or generic register based mux producer.
+
+Required properties in addition to the MDIO Bus multiplexer properties:
+
+- compatible : should be "mmio-mux-multiplexer"
+- mux-controls : mux controller node to use for operating the mux
+- mdio-parent-bus : phandle to the parent MDIO bus.
+
+each child node of mdio bus multiplexer consumer device represent a mdio
+bus.
+
+for more information please refer
+Documentation/devicetree/bindings/mux/mux-controller.txt
+and Documentation/devicetree/bindings/net/mdio-mux.txt
+
+Example:
+In below example the Mux producer and consumer are separate nodes.
+
+&i2c0 {
+	fpga@66 { // fpga connected to i2c
+		compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c",
+			     "simple-mfd";
+		reg = <0x66>;
+
+		mux: mux-controller { // Mux Producer
+			compatible = "reg-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */
+					<0x54 0x07>; /* 1: reg 0x54, bits 2:0 */
+		};
+	};
+};
+
+mdio-mux-1 { // Mux consumer
+	compatible = "mdio-mux-multiplexer";
+	mux-controls = <&mux 0>;
+	mdio-parent-bus = <&emdio1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	mdio@0 {
+		reg = <0x0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	mdio@8 {
+		reg = <0x8>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	..
+	..
+};
+
+mdio-mux-2 { // Mux consumer
+	compatible = "mdio-mux-multiplexer";
+	mux-controls = <&mux 1>;
+	mdio-parent-bus = <&emdio2>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	mdio@0 {
+		reg = <0x0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	mdio@1 {
+		reg = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	..
+	..
+};