Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 70 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
new file mode 100644
index 000000000..b6acbe694
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
@@ -0,0 +1,70 @@
+Amlogic Meson AXG DWC PCIE SoC controller
+
+Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
+It shares common functions with the PCIe DesignWare core driver and
+inherits common properties defined in
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
+
+Additional properties are described here:
+
+Required properties:
+- compatible:
+	should contain :
+	- "amlogic,axg-pcie" for AXG SoC Family
+	- "amlogic,g12a-pcie" for G12A SoC Family
+	to identify the core.
+- reg:
+	should contain the configuration address space.
+- reg-names: Must be
+	- "elbi"	External local bus interface registers
+	- "cfg"		Meson specific registers
+	- "config"	PCIe configuration space
+- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must include the following entries:
+	- "pclk"       PCIe GEN 100M PLL clock
+	- "port"       PCIe_x(A or B) RC clock gate
+	- "general"    PCIe Phy clock
+- resets: phandle to the reset lines.
+- reset-names: must contain "port" and "apb"
+       - "port"        Port A or B reset
+       - "apb"         Share APB reset
+- phys: should contain a phandle to the PCIE phy
+- phy-names: must contain "pcie"
+
+- device_type:
+	should be "pci". As specified in designware-pcie.txt
+
+
+Example configuration:
+
+	pcie: pcie@f9800000 {
+			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
+			reg = <0x0 0xf9800000 0x0 0x400000
+					0x0 0xff646000 0x0 0x2000
+					0x0 0xf9f00000 0x0 0x100000>;
+			reg-names = "elbi", "cfg", "config";
+			reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
+
+			clocks = <&clkc CLKID_USB
+					&clkc CLKID_PCIE_A
+					&clkc CLKID_PCIE_CML_EN0>;
+			clock-names = "general",
+					"pclk",
+					"port";
+			resets = <&reset RESET_PCIE_A>,
+				<&reset RESET_PCIE_APB>;
+			reset-names = "port",
+					"apb";
+			phys = <&pcie_phy>;
+			phy-names = "pcie";
+	};