Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 97 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
new file mode 100644
index 000000000..de4b2baf9
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
@@ -0,0 +1,97 @@
+* Freescale i.MX6 PCIe interface
+
+This PCIe host controller is based on the Synopsys DesignWare PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible:
+	- "fsl,imx6q-pcie"
+	- "fsl,imx6sx-pcie",
+	- "fsl,imx6qp-pcie"
+	- "fsl,imx7d-pcie"
+	- "fsl,imx8mq-pcie"
+- reg: base address and length of the PCIe controller
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+  entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+	- "msi": The interrupt that is asserted when an MSI is received
+- clock-names: Must include the following additional entries:
+	- "pcie_phy"
+
+Optional properties:
+- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0
+- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0
+- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20
+- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127
+- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127
+- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for
+  gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs
+  do not meet gen2 jitter requirements and thus for gen2 capability a gen2
+  compliant clock generator should be used and configured.
+- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset
+  signal. It's not polarity aware and defaults to active-low reset sequence
+  (L=reset state, H=operation state).
+- reset-gpio-active-high: If present then the reset sequence using the GPIO
+  specified in the "reset-gpio" property is reversed (H=reset state,
+  L=operation state).
+- vpcie-supply: Should specify the regulator in charge of PCIe port power.
+  The regulator will be enabled when initializing the PCIe host and
+  disabled either as part of the init process or when shutting down the
+  host.
+
+Additional required properties for imx6sx-pcie:
+- clock names: Must include the following additional entries:
+	- "pcie_inbound_axi"
+- power-domains: Must be set to phandles pointing to the DISPLAY and
+  PCIE_PHY power domains
+- power-domain-names: Must be "pcie", "pcie_phy"
+
+Additional required properties for imx7d-pcie and imx8mq-pcie:
+- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain
+- resets: Must contain phandles to PCIe-related reset lines exposed by SRC
+  IP block
+- reset-names: Must contain the following entries:
+	       - "pciephy"
+	       - "apps"
+	       - "turnoff"
+- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node.
+
+Additional required properties for imx8mq-pcie:
+- clock-names: Must include the following additional entries:
+	- "pcie_aux"
+
+Example:
+
+	pcie@01000000 {
+		compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+		reg = <0x01ffc000 0x04000>,
+		      <0x01f00000 0x80000>;
+		reg-names = "dbi", "config";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
+			  0x81000000 0 0          0x01f80000 0 0x00010000
+			  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
+		num-lanes = <1>;
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "msi";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0x7>;
+		interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks 144>, <&clks 206>, <&clks 189>;
+		clock-names = "pcie", "pcie_bus", "pcie_phy";
+	};
+
+* Freescale i.MX7d PCIe PHY
+
+This is the PHY associated with the IMX7d PCIe controller.  It's used by the
+PCI-e controller via the fsl,imx7d-pcie-phy phandle.
+
+Required properties:
+- compatible:
+	- "fsl,imx7d-pcie-phy"
+- reg: base address and length of the PCIe PHY controller