Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 185 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
new file mode 100644
index 000000000..448d36a85
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
@@ -0,0 +1,185 @@
+Qualcomm PMIC Multi-Purpose Pin (MPP) block
+
+This binding describes the MPP block(s) found in the 8xxx series
+of PMIC's from Qualcomm.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: Should contain one of:
+		    "qcom,pm8018-mpp",
+		    "qcom,pm8038-mpp",
+		    "qcom,pm8058-mpp",
+		    "qcom,pm8821-mpp",
+		    "qcom,pm8841-mpp",
+		    "qcom,pm8916-mpp",
+		    "qcom,pm8917-mpp",
+		    "qcom,pm8921-mpp",
+		    "qcom,pm8941-mpp",
+		    "qcom,pm8950-mpp",
+		    "qcom,pmi8950-mpp",
+		    "qcom,pm8994-mpp",
+		    "qcom,pma8084-mpp",
+
+		    And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp"
+		    if the device is on an spmi bus or an ssbi bus respectively.
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Register base of the MPP block and length.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Must contain an array of encoded interrupt specifiers for
+		    each available MPP
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: Mark the device node as a GPIO controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 2;
+		    the first cell will be used to define MPP number and the
+		    second denotes the flags for this MPP
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin or a list of pins. This configuration can include the
+mux function to select on those pin(s), and various pin configuration
+parameters, as listed below.
+
+SUBNODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of MPP pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    mpp1-mpp4 for pm8841
+		    mpp1-mpp4 for pm8916
+		    mpp1-mpp8 for pm8941
+		    mpp1-mpp4 for pm8950
+		    mpp1-mpp4 for pmi8950
+		    mpp1-mpp4 for pma8084
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins.  Valid values are:
+		    "digital",
+		    "analog",
+		    "sink"
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as no pull.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <u32>
+	Definition: The specified pins should be configured as pull up.
+		    Valid values are 600, 10000 and 30000 in bidirectional mode
+		    only, i.e. when operating in qcom,analog-mode and input and
+		    outputs are enabled. The hardware ignores the configuration
+		    when operating in other modes.
+
+- bias-high-impedance:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins will put in high-Z mode and disabled.
+
+- input-enable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are put in input mode, i.e. their input
+		    buffer is enabled
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+
+- power-source:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the power source for the specified pins. Valid power
+		    sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+- qcom,analog-level:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the source for analog output. Valued values are
+		    defined in <dt-binding/pinctrl/qcom,pmic-mpp.h>
+		    PMIC_MPP_AOUT_LVL_*
+
+- qcom,dtest:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects which dtest rail to be routed in the various functions.
+		    Valid values are 1-4
+
+- qcom,amux-route:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the source for analog input. Valid values are
+		    defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+		    PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
+- qcom,paired:
+	Usage: optional
+	Value type: <none>
+	Definition: Indicates that the pin should be operating in paired mode.
+
+Example:
+
+	mpps@a000 {
+		compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
+		reg = <0xa000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm8841_default>;
+
+		pm8841_default: default {
+			gpio {
+				pins = "mpp1", "mpp2", "mpp3", "mpp4";
+				function = "digital";
+				input-enable;
+				power-source = <PM8841_MPP_S3>;
+			};
+		};
+	};