Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 140 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt
new file mode 100644
index 000000000..6cd83d920
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt
@@ -0,0 +1,140 @@
+Binding for Samsung S5M8767 regulator block
+===========================================
+
+This is a part of device tree bindings for S5M family multi-function devices.
+More information can be found in bindings/mfd/sec-core.txt file.
+
+The S5M8767 device provide buck and LDO regulators.
+
+To register these with regulator framework instantiate under main device node
+a sub-node named "regulators" with more sub-nodes for each regulator using the
+common regulator binding documented in:
+ - Documentation/devicetree/bindings/regulator/regulator.txt
+
+
+Required properties of the main device node (the parent!):
+ - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
+   for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
+
+ [1] If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
+     property is specified, then all the eight voltage values for the
+     's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
+
+Optional properties of the main device node (the parent!):
+ - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+   units for buck2 when changing voltage using gpio dvs. Refer to [1] below
+   for additional information.
+
+ - s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+   units for buck3 when changing voltage using gpio dvs. Refer to [1] below
+   for additional information.
+
+ - s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+   units for buck4 when changing voltage using gpio dvs. Refer to [1] below
+   for additional information.
+
+ - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
+ - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
+ - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
+
+Additional properties required if either of the optional properties are used:
+
+ - s5m8767,pmic-buck-default-dvs-idx: Default voltage setting selected from
+   the possible 8 options selectable by the dvs gpios. The value of this
+   property should be between 0 and 7. If not specified or if out of range, the
+   default value of this property is set to 0.
+
+ - s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
+   for dvs. The format of the gpio specifier depends in the gpio controller.
+
+
+Names of regulators supported by S5M8767 device:
+	- LDOn
+		  - valid values for n are 1 to 28
+		  - Example: LDO1, LDO2, LDO28
+	- BUCKn
+		  - valid values for n are 1 to 9.
+		  - Example: BUCK1, BUCK2, BUCK9
+Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of device.
+
+
+Optional properties of the nodes under "regulators" sub-node:
+ - op_mode: describes the different operating modes of the LDO's with
+            power mode change in SOC. The different possible values are,
+             0 - always off mode
+             1 - on in normal mode
+             2 - low power mode
+             3 - suspend mode
+ - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
+                                   GPIO controlling this regulator
+                                   (enable/disable); This is valid only
+                                   for buck9.
+
+Example:
+
+	s5m8767_pmic@66 {
+		compatible = "samsung,s5m8767-pmic";
+		reg = <0x66>;
+
+		s5m8767,pmic-buck2-uses-gpio-dvs;
+		s5m8767,pmic-buck3-uses-gpio-dvs;
+		s5m8767,pmic-buck4-uses-gpio-dvs;
+
+		s5m8767,pmic-buck-default-dvs-idx = <0>;
+
+		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
+						 <&gpx0 1 0>, /* DVS2 */
+						 <&gpx0 2 0>; /* DVS3 */
+
+		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
+						<&gpx2 4 0>, /* SET2 */
+						<&gpx2 5 0>; /* SET3 */
+
+		s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+						 <1250000>, <1200000>,
+						 <1150000>, <1100000>,
+						 <1000000>, <950000>;
+
+		s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+						 <1100000>, <1100000>,
+						 <1000000>, <1000000>,
+						 <1000000>, <1000000>;
+
+		s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ABB_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>; /* Normal Mode */
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF_1.2V";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vemmc_reg: BUCK9 {
+				regulator-name = "VMEM_VDD_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <3>; /* Standby Mode */
+				s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>;
+			};
+		};
+	};