diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/sound/cs35l33.txt | |
parent | Initial commit. (diff) | |
download | linux-430c2fc249ea5c0536abd21c23382884005c9093.tar.xz linux-430c2fc249ea5c0536abd21c23382884005c9093.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'Documentation/devicetree/bindings/sound/cs35l33.txt')
-rw-r--r-- | Documentation/devicetree/bindings/sound/cs35l33.txt | 124 |
1 files changed, 124 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs35l33.txt b/Documentation/devicetree/bindings/sound/cs35l33.txt new file mode 100644 index 000000000..dc5a355d1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs35l33.txt @@ -0,0 +1,124 @@ +CS35L33 Speaker Amplifier + +Required properties: + + - compatible : "cirrus,cs35l33" + + - reg : the I2C address of the device for I2C + + - VA-supply, VP-supply : power supplies for the device, + as covered in + Documentation/devicetree/bindings/regulator/regulator.txt. + +Optional properties: + + - reset-gpios : gpio used to reset the amplifier + + - interrupts : IRQ line info CS35L33. + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for further information relating to interrupt properties) + + - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is + 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with + a value of 1 and will increase at a step size of 100mV until a maximum of + 8000mV. + + - cirrus,ramp-rate : On power up, it affects the time from when the power + up sequence begins to the time the audio reaches a full-scale output. + On power down, it affects the time from when the power-down sequence + begins to when the amplifier disables the PWM outputs. If this property + is not set then soft ramping will be disabled and ramp time would be + 20ms. If this property is set to 0,1,2,3 then ramp times would be 40ms, + 60ms,100ms,175ms respectively for 48KHz sample rate. + + - cirrus,boost-ipk : The maximum current allowed for the boost converter. + The range starts at 1850000uA and goes to a maximum of 3600000uA + with a step size of 15625uA. The default is 2500000uA. + + - cirrus,imon-adc-scale : Configures the scaling of data bits from the IMON + ADC data word. This property can be set as a value of 0 for bits 15 down + to 0, 6 for 21 down to 6, 7, for 22 down to 7, 8 for 23 down to 8. + + +Optional H/G Algorithm sub-node: + +The cs35l33 node can have a single "cirrus,hg-algo" sub-node that will enable +the internal H/G Algorithm. + + - cirrus,hg-algo : Sub-node for internal Class H/G algorithm that + controls the amplifier supplies. + +Optional properties for the "cirrus,hg-algo" sub-node: + + - cirrus,mem-depth : Memory depth for the Class H/G algorithm measured in + LRCLK cycles. If this property is set to 0, 1, 2, or 3 then the memory + depths will be 1, 4, 8, 16 LRCLK cycles. The default is 16 LRCLK cycles. + + cirrus,release-rate : The number of consecutive LRCLK periods before + allowing release condition tracking updates. The number of LRCLK periods + start at 3 to a maximum of 255. + + - cirrus,ldo-thld : Configures the signal threshold at which the PWM output + stage enters LDO operation. Starts as a default value of 50mV for a value + of 1 and increases with a step size of 50mV to a maximum of 750mV (value of + 0xF). + + - cirrus,ldo-path-disable : This is a boolean property. If present, the H/G + algorithm uses the max detection path. If not present, the LDO + detection path is used. + + - cirrus,ldo-entry-delay : The LDO entry delay in milliseconds before the H/G + algorithm switches to the LDO voltage. This property can be set to values + from 0 to 7 for delays of 5ms, 10ms, 50ms, 100ms, 200ms, 500ms, 1000ms. + The default is 100ms. + + - cirrus,vp-hg-auto : This is a boolean property. When set, class H/G VPhg + automatic updating is enabled. + + - cirrus,vp-hg : Class H/G algorithm VPhg. Controls the H/G algorithm's + reference to the VP voltage for when to start generating a boosted VBST. + The reference voltage starts at 3000mV with a value of 0x3 and is increased + by 100mV per step to a maximum of 5500mV. + + - cirrus,vp-hg-rate : The rate (number of LRCLK periods) at which the VPhg is + allowed to increase to a higher voltage when using VPhg automatic + tracking. This property can be set to values from 0 to 3 with rates of 128 + periods, 2048 periods, 32768 periods, and 524288 periods. + The default is 32768 periods. + + - cirrus,vp-hg-va : VA calculation reference for automatic VPhg tracking + using VPMON. This property can be set to values from 0 to 6 starting at + 1800mV with a step size of 50mV up to a maximum value of 1750mV. + Default is 1800mV. + +Example: + +cs35l33: cs35l33@40 { + compatible = "cirrus,cs35l33"; + reg = <0x40>; + + VA-supply = <&ldo5_reg>; + VP-supply = <&ldo5_reg>; + + interrupt-parent = <&gpio8>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&cs47l91 34 0>; + + cirrus,ramp-rate = <0x0>; + cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */ + cirrus,boost-ipk = <0xE0>; /* 3600mA */ + cirrus,imon-adc-scale = <0> /* Bits 15 down to 0 */ + + cirrus,hg-algo { + cirrus,mem-depth = <0x3>; + cirrus,release-rate = <0x3>; + cirrus,ldo-thld = <0x1>; + cirrus,ldo-path-disable = <0x0>; + cirrus,ldo-entry-delay=<0x4>; + cirrus,vp-hg-auto; + cirrus,vp-hg=<0xF>; + cirrus,vp-hg-rate=<0x2>; + cirrus,vp-hg-va=<0x0>; + }; +}; |