Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

7 files changed, 386 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/ufs/cdns,ufshc.txt b/Documentation/devicetree/bindings/ufs/cdns,ufshc.txt
new file mode 100644
index 000000000..02347b017
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/cdns,ufshc.txt
@@ -0,0 +1,32 @@
+* Cadence Universal Flash Storage (UFS) Controller
+
+UFS nodes are defined to describe on-chip UFS host controllers.
+Each UFS controller instance should have its own node.
+Please see the ufshcd-pltfrm.txt for a list of all available properties.
+
+Required properties:
+- compatible	: Compatible list, contains one of the following controllers:
+			"cdns,ufshc" - Generic CDNS HCI,
+			"cdns,ufshc-m31-16nm" - CDNS UFS HC + M31 16nm PHY
+		  complemented with the JEDEC version:
+			"jedec,ufs-2.0"
+
+- reg		: Address and length of the UFS register set.
+- interrupts	: One interrupt mapping.
+- freq-table-hz	: Clock frequency table.
+		  See the ufshcd-pltfrm.txt for details.
+- clocks	: List of phandle and clock specifier pairs.
+- clock-names	: List of clock input name strings sorted in the same
+		  order as the clocks property. "core_clk" is mandatory.
+		  Depending on a type of a PHY,
+		  the "phy_clk" clock can also be added, if needed.
+
+Example:
+	ufs@fd030000 {
+		compatible = "cdns,ufshc", "jedec,ufs-2.0";
+		reg = <0xfd030000 0x10000>;
+		interrupts = <0 1 IRQ_TYPE_LEVEL_HIGH>;
+		freq-table-hz = <0 0>, <0 0>;
+		clocks = <&ufs_core_clk>, <&ufs_phy_clk>;
+		clock-names = "core_clk", "phy_clk";
+	};
diff --git a/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt
new file mode 100644
index 000000000..71c077796
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt
@@ -0,0 +1,26 @@
+* Universal Flash Storage (UFS) DesignWare Host Controller
+
+DWC_UFS nodes are defined to describe on-chip UFS host controllers and MPHY.
+Each UFS controller instance should have its own node.
+
+Required properties:
+- compatible	: compatible list must contain the PHY type & version:
+			"snps,g210-tc-6.00-20bit"
+			"snps,g210-tc-6.00-40bit"
+		  complemented with the Controller IP version:
+			"snps,dwc-ufshcd-1.40a"
+		  complemented with the JEDEC version:
+			"jedec,ufs-1.1"
+			"jedec,ufs-2.0"
+
+- reg		: <registers mapping>
+- interrupts	: <interrupt mapping for UFS host controller IRQ>
+
+Example for a setup using a 1.40a DWC Controller with a 6.00 G210 40-bit TC:
+	dwc-ufs@d0000000 {
+		compatible = "snps,g210-tc-6.00-40bit",
+			     "snps,dwc-ufshcd-1.40a",
+			     "jedec,ufs-2.0";
+		reg = < 0xd0000000 0x10000 >;
+		interrupts = < 24 >;
+	};
diff --git a/Documentation/devicetree/bindings/ufs/ti,j721e-ufs.yaml b/Documentation/devicetree/bindings/ufs/ti,j721e-ufs.yaml
new file mode 100644
index 000000000..4d13e6bc1
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ti,j721e-ufs.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/ufs/ti,j721e-ufs.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI J721e UFS Host Controller Glue Driver
+
+maintainers:
+  - Vignesh Raghavendra <vigneshr@ti.com>
+
+properties:
+  compatible:
+    items:
+      - const: ti,j721e-ufs
+
+  reg:
+    maxItems: 1
+    description: address of TI UFS glue registers
+
+  clocks:
+    maxItems: 1
+    description: phandle to the M-PHY clock
+
+  power-domains:
+    maxItems: 1
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clock-parents:
+    maxItems: 1
+
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 2
+
+  ranges: true
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - power-domains
+
+patternProperties:
+  "^ufs@[0-9a-f]+$":
+    type: object
+    description: |
+      Cadence UFS controller node must be the child node. Refer
+      Documentation/devicetree/bindings/ufs/cdns,ufshc.txt for binding
+      documentation of child node
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        ufs-wrapper@4e80000 {
+            compatible = "ti,j721e-ufs";
+            reg = <0x0 0x4e80000 0x0 0x100>;
+            power-domains = <&k3_pds 277>;
+            clocks = <&k3_clks 277 1>;
+            assigned-clocks = <&k3_clks 277 1>;
+            assigned-clock-parents = <&k3_clks 277 4>;
+
+            ranges = <0x0 0x0 0x0 0x4e80000 0x0 0x14000>;
+            #address-cells = <2>;
+            #size-cells = <2>;
+
+            ufs@4000 {
+                compatible = "cdns,ufshc-m31-16nm", "jedec,ufs-2.0";
+                reg = <0x0 0x4000 0x0 0x10000>;
+                interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+                freq-table-hz = <19200000 19200000>;
+                power-domains = <&k3_pds 277>;
+                clocks = <&k3_clks 277 1>;
+                assigned-clocks = <&k3_clks 277 1>;
+                assigned-clock-parents = <&k3_clks 277 4>;
+                clock-names = "core_clk";
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
new file mode 100644
index 000000000..0b83df1a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt
@@ -0,0 +1,42 @@
+* Hisilicon Universal Flash Storage (UFS) Host Controller
+
+UFS nodes are defined to describe on-chip UFS hardware macro.
+Each UFS Host Controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains one of the following -
+					"hisilicon,hi3660-ufs", "jedec,ufs-1.1" for hisi ufs
+					host controller present on Hi3660 chipset.
+					"hisilicon,hi3670-ufs", "jedec,ufs-2.1" for hisi ufs
+					host controller present on Hi3670 chipset.
+- reg               : should contain UFS register address space & UFS SYS CTRL register address,
+- interrupts        : interrupt number
+- clocks	        : List of phandle and clock specifier pairs
+- clock-names       : List of clock input name strings sorted in the same
+					order as the clocks property. "ref_clk", "phy_clk" is optional
+- freq-table-hz     : Array of <min max> operating frequencies stored in the same
+                      order as the clocks property. If this property is not
+                      defined or a value in the array is "0" then it is assumed
+                      that the frequency is set by the parent clock or a
+                      fixed rate clock source.
+- resets            : describe reset node register
+- reset-names       : reset node register, the "rst" corresponds to reset the whole UFS IP.
+
+Example:
+
+	ufs: ufs@ff3b0000 {
+		compatible = "hisilicon,hi3660-ufs", "jedec,ufs-1.1";
+		/* 0: HCI standard */
+		/* 1: UFS SYS CTRL */
+		reg = <0x0 0xff3b0000 0x0 0x1000>,
+			<0x0 0xff3b1000 0x0 0x1000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>,
+			<&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>;
+		clock-names = "ref_clk", "phy_clk";
+		freq-table-hz = <0 0>, <0 0>;
+		/* offset: 0x84; bit: 12  */
+		resets = <&crg_rst 0x84 12>;
+		reset-names = "rst";
+	};
diff --git a/Documentation/devicetree/bindings/ufs/ufs-mediatek.txt b/Documentation/devicetree/bindings/ufs/ufs-mediatek.txt
new file mode 100644
index 000000000..63a953b67
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-mediatek.txt
@@ -0,0 +1,45 @@
+* Mediatek Universal Flash Storage (UFS) Host Controller
+
+UFS nodes are defined to describe on-chip UFS hardware macro.
+Each UFS Host Controller should have its own node.
+
+To bind UFS PHY with UFS host controller, the controller node should
+contain a phandle reference to UFS M-PHY node.
+
+Required properties for UFS nodes:
+- compatible         : Compatible list, contains the following controller:
+                       "mediatek,mt8183-ufshci" for MediaTek UFS host controller
+                       present on MT8183 chipsets.
+                       "mediatek,mt8192-ufshci" for MediaTek UFS host controller
+                       present on MT8192 chipsets.
+- reg                : Address and length of the UFS register set.
+- phys               : phandle to m-phy.
+- clocks             : List of phandle and clock specifier pairs.
+- clock-names        : List of clock input name strings sorted in the same
+                       order as the clocks property. "ufs" is mandatory.
+                       "ufs": ufshci core control clock.
+- freq-table-hz      : Array of <min max> operating frequencies stored in the same
+                       order as the clocks property. If this property is not
+                       defined or a value in the array is "0" then it is assumed
+                       that the frequency is set by the parent clock or a
+                       fixed rate clock source.
+- vcc-supply         : phandle to VCC supply regulator node.
+
+Example:
+
+	ufsphy: phy@11fa0000 {
+		...
+	};
+
+	ufshci@11270000 {
+		compatible = "mediatek,mt8183-ufshci";
+		reg = <0 0x11270000 0 0x2300>;
+		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>;
+		phys = <&ufsphy>;
+
+		clocks = <&infracfg_ao INFRACFG_AO_UFS_CG>;
+		clock-names = "ufs";
+		freq-table-hz = <0 0>;
+
+		vcc-supply = <&mt_pmic_vemc_ldo_reg>;
+	};
diff --git a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt
new file mode 100644
index 000000000..fd59f93e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt
@@ -0,0 +1,63 @@
+* Qualcomm Technologies Inc Universal Flash Storage (UFS) PHY
+
+UFSPHY nodes are defined to describe on-chip UFS PHY hardware macro.
+Each UFS PHY node should have its own node.
+
+To bind UFS PHY with UFS host controller, the controller node should
+contain a phandle reference to UFS PHY node.
+
+Required properties:
+- compatible        : compatible list, contains one of the following -
+			"qcom,ufs-phy-qmp-20nm" for 20nm ufs phy,
+			"qcom,ufs-phy-qmp-14nm" for legacy 14nm ufs phy,
+			"qcom,msm8996-ufs-phy-qmp-14nm" for 14nm ufs phy
+			 present on MSM8996 chipset.
+- reg               : should contain PHY register address space (mandatory),
+- reg-names         : indicates various resources passed to driver (via reg proptery) by name.
+                      Required "reg-names" is "phy_mem".
+- #phy-cells        : This property shall be set to 0
+- vdda-phy-supply   : phandle to main PHY supply for analog domain
+- vdda-pll-supply   : phandle to PHY PLL and Power-Gen block power supply
+- clocks	    : List of phandle and clock specifier pairs
+- clock-names       : List of clock input name strings sorted in the same
+		      order as the clocks property. "ref_clk_src", "ref_clk",
+		      "tx_iface_clk" & "rx_iface_clk" are mandatory but
+		      "ref_clk_parent" is optional
+
+Optional properties:
+- vdda-phy-max-microamp : specifies max. load that can be drawn from phy supply
+- vdda-pll-max-microamp : specifies max. load that can be drawn from pll supply
+- vddp-ref-clk-supply   : phandle to UFS device ref_clk pad power supply
+- vddp-ref-clk-max-microamp : specifies max. load that can be drawn from this supply
+- resets : specifies the PHY reset in the UFS controller
+
+Example:
+
+	ufsphy1: ufsphy@fc597000 {
+		compatible = "qcom,ufs-phy-qmp-20nm";
+		reg = <0xfc597000 0x800>;
+		reg-names = "phy_mem";
+		#phy-cells = <0>;
+		vdda-phy-supply = <&pma8084_l4>;
+		vdda-pll-supply = <&pma8084_l12>;
+		vdda-phy-max-microamp = <50000>;
+		vdda-pll-max-microamp = <1000>;
+		clock-names = "ref_clk_src",
+			"ref_clk_parent",
+			"ref_clk",
+			"tx_iface_clk",
+			"rx_iface_clk";
+		clocks = <&clock_rpm clk_ln_bb_clk>,
+			<&clock_gcc clk_pcie_1_phy_ldo >,
+			<&clock_gcc clk_ufs_phy_ldo>,
+			<&clock_gcc clk_gcc_ufs_tx_cfg_clk>,
+			<&clock_gcc clk_gcc_ufs_rx_cfg_clk>;
+		resets = <&ufshc 0>;
+	};
+
+	ufshc: ufshc@fc598000 {
+		#reset-cells = <1>;
+		...
+		phys = <&ufsphy1>;
+		phy-names = "ufsphy";
+	};
diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
new file mode 100644
index 000000000..415ccdd74
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt
@@ -0,0 +1,87 @@
+* Universal Flash Storage (UFS) Host Controller
+
+UFSHC nodes are defined to describe on-chip UFS host controllers.
+Each UFS controller instance should have its own node.
+
+Required properties:
+- compatible		: must contain "jedec,ufs-1.1" or "jedec,ufs-2.0"
+
+			  For Qualcomm SoCs must contain, as below, an
+			  SoC-specific compatible along with "qcom,ufshc" and
+			  the appropriate jedec string:
+			    "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+			    "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+			    "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+			    "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+			    "qcom,sm8150-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
+- interrupts        : <interrupt mapping for UFS host controller IRQ>
+- reg               : <registers mapping>
+
+Optional properties:
+- phys                  : phandle to UFS PHY node
+- phy-names             : the string "ufsphy" when is found in a node, along
+                          with "phys" attribute, provides phandle to UFS PHY node
+- vdd-hba-supply        : phandle to UFS host controller supply regulator node
+- vcc-supply            : phandle to VCC supply regulator node
+- vccq-supply           : phandle to VCCQ supply regulator node
+- vccq2-supply          : phandle to VCCQ2 supply regulator node
+- vcc-supply-1p8        : For embedded UFS devices, valid VCC range is 1.7-1.95V
+                          or 2.7-3.6V. This boolean property when set, specifies
+			  to use low voltage range of 1.7-1.95V. Note for external
+			  UFS cards this property is invalid and valid VCC range is
+			  always 2.7-3.6V.
+- vcc-max-microamp      : specifies max. load that can be drawn from vcc supply
+- vccq-max-microamp     : specifies max. load that can be drawn from vccq supply
+- vccq2-max-microamp    : specifies max. load that can be drawn from vccq2 supply
+
+- clocks                : List of phandle and clock specifier pairs
+- clock-names           : List of clock input name strings sorted in the same
+                          order as the clocks property.
+			  "ref_clk" indicates reference clock frequency.
+			  UFS host supplies reference clock to UFS device and UFS device
+			  specification allows host to provide one of the 4 frequencies (19.2 MHz,
+			  26 MHz, 38.4 MHz, 52MHz) for reference clock. This "ref_clk" entry is
+			  parsed and used to update the reference clock setting in device.
+			  Defaults to 26 MHz(as per specification) if not specified by host.
+- freq-table-hz		: Array of <min max> operating frequencies stored in the same
+                          order as the clocks property. If this property is not
+			  defined or a value in the array is "0" then it is assumed
+			  that the frequency is set by the parent clock or a
+			  fixed rate clock source.
+-lanes-per-direction	: number of lanes available per direction - either 1 or 2.
+			  Note that it is assume same number of lanes is used both
+			  directions at once. If not specified, default is 2 lanes per direction.
+- #reset-cells		: Must be <1> for Qualcomm UFS controllers that expose
+			  PHY reset from the UFS controller.
+- resets            : reset node register
+- reset-names       : describe reset node register, the "rst" corresponds to reset the whole UFS IP.
+- reset-gpios       : A phandle and gpio specifier denoting the GPIO connected
+		      to the RESET pin of the UFS memory device.
+
+Note: If above properties are not defined it can be assumed that the supply
+regulators or clocks are always on.
+
+Example:
+	ufshc@fc598000 {
+		compatible = "jedec,ufs-1.1";
+		reg = <0xfc598000 0x800>;
+		interrupts = <0 28 0>;
+
+		vdd-hba-supply = <&xxx_reg0>;
+		vcc-supply = <&xxx_reg1>;
+		vcc-supply-1p8;
+		vccq-supply = <&xxx_reg2>;
+		vccq2-supply = <&xxx_reg3>;
+		vcc-max-microamp = 500000;
+		vccq-max-microamp = 200000;
+		vccq2-max-microamp = 200000;
+
+		clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>;
+		clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk";
+		freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>;
+		resets = <&reset 0 1>;
+		reset-names = "rst";
+		phys = <&ufsphy1>;
+		phy-names = "ufsphy";
+		#reset-cells = <1>;
+	};