diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/devicetree/bindings/usb/msm-hsusb.txt | |
parent | Initial commit. (diff) | |
download | linux-upstream/5.10.209.tar.xz linux-upstream/5.10.209.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
-rw-r--r-- | Documentation/devicetree/bindings/usb/msm-hsusb.txt | 110 |
1 files changed, 110 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt new file mode 100644 index 000000000..8654a3ec2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -0,0 +1,110 @@ +MSM SoC HSUSB controllers + +EHCI + +Required properties: +- compatible: Should contain "qcom,ehci-host" +- regs: offset and length of the register set in the memory map +- usb-phy: phandle for the PHY device + +Example EHCI controller device node: + + ehci: ehci@f9a55000 { + compatible = "qcom,ehci-host"; + reg = <0xf9a55000 0x400>; + usb-phy = <&usb_otg>; + }; + +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- switch-gpio: A phandle + gpio-specifier pair. Some boards are using Dual + SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex + D+/D- USB lines between connectors. + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +- qcom,phy-num: Select number of pyco-phy to use, can be one of + 0 - PHY one, default + 1 - Second PHY + Some platforms may have configuration to allow USB + controller work with any of the two HSPHYs present. + +- qcom,vdd-levels: This property must be a list of three integer values + (no, min, max) where each value represents either a voltage + in microvolts or a value corresponding to voltage corner. + +- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy + and controller driver therefore enables pull-up explicitly + before starting controller using usbcmd run/stop bit. + +- extcon: phandles to external connector devices. First phandle + should point to external connector, which provide "USB" + cable events, the second should point to external connector + device, which provide "USB-HOST" cable events. If one of + the external connector devices is not required empty <0> + phandle should be specified. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + qcom,vdd-levels = <1 5 7>; + }; |