diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/driver-api/serial/moxa-smartio.rst | |
parent | Initial commit. (diff) | |
download | linux-upstream/5.10.209.tar.xz linux-upstream/5.10.209.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
-rw-r--r-- | Documentation/driver-api/serial/moxa-smartio.rst | 615 |
1 files changed, 615 insertions, 0 deletions
diff --git a/Documentation/driver-api/serial/moxa-smartio.rst b/Documentation/driver-api/serial/moxa-smartio.rst new file mode 100644 index 000000000..156100f17 --- /dev/null +++ b/Documentation/driver-api/serial/moxa-smartio.rst @@ -0,0 +1,615 @@ +============================================================= +MOXA Smartio/Industio Family Device Driver Installation Guide +============================================================= + +.. note:: + + This file is outdated. It needs some care in order to make it + updated to Kernel 5.0 and upper + +Copyright (C) 2008, Moxa Inc. + +Date: 01/21/2008 + +.. Content + + 1. Introduction + 2. System Requirement + 3. Installation + 3.1 Hardware installation + 3.2 Driver files + 3.3 Device naming convention + 3.4 Module driver configuration + 3.5 Static driver configuration for Linux kernel 2.4.x and 2.6.x. + 3.6 Custom configuration + 3.7 Verify driver installation + 4. Utilities + 5. Setserial + 6. Troubleshooting + +1. Introduction +^^^^^^^^^^^^^^^ + + The Smartio/Industio/UPCI family Linux driver supports following multiport + boards. + + - 2 ports multiport board + CP-102U, CP-102UL, CP-102UF + CP-132U-I, CP-132UL, + CP-132, CP-132I, CP132S, CP-132IS, + CI-132, CI-132I, CI-132IS, + (C102H, C102HI, C102HIS, C102P, CP-102, CP-102S) + + - 4 ports multiport board + CP-104EL, + CP-104UL, CP-104JU, + CP-134U, CP-134U-I, + C104H/PCI, C104HS/PCI, + CP-114, CP-114I, CP-114S, CP-114IS, CP-114UL, + C104H, C104HS, + CI-104J, CI-104JS, + CI-134, CI-134I, CI-134IS, + (C114HI, CT-114I, C104P), + POS-104UL, + CB-114, + CB-134I + + - 8 ports multiport board + CP-118EL, CP-168EL, + CP-118U, CP-168U, + C168H/PCI, + C168H, C168HS, + (C168P), + CB-108 + + This driver and installation procedure have been developed upon Linux Kernel + 2.4.x and 2.6.x. This driver supports Intel x86 hardware platform. In order + to maintain compatibility, this version has also been properly tested with + RedHat, Mandrake, Fedora and S.u.S.E Linux. However, if compatibility problem + occurs, please contact Moxa at support@moxa.com.tw. + + In addition to device driver, useful utilities are also provided in this + version. They are: + + - msdiag + Diagnostic program for displaying installed Moxa + Smartio/Industio boards. + - msmon + Monitor program to observe data count and line status signals. + - msterm A simple terminal program which is useful in testing serial + ports. + - io-irq.exe + Configuration program to setup ISA boards. Please note that + this program can only be executed under DOS. + + All the drivers and utilities are published in form of source code under + GNU General Public License in this version. Please refer to GNU General + Public License announcement in each source code file for more detail. + + In Moxa's Web sites, you may always find latest driver at http://www.moxa.com/. + + This version of driver can be installed as Loadable Module (Module driver) + or built-in into kernel (Static driver). You may refer to following + installation procedure for suitable one. Before you install the driver, + please refer to hardware installation procedure in the User's Manual. + + We assume the user should be familiar with following documents. + + - Serial-HOWTO + - Kernel-HOWTO + +2. System Requirement +^^^^^^^^^^^^^^^^^^^^^ + + - Hardware platform: Intel x86 machine + - Kernel version: 2.4.x or 2.6.x + - gcc version 2.72 or later + - Maximum 4 boards can be installed in combination + +3. Installation +^^^^^^^^^^^^^^^ + +3.1 Hardware installation +========================= + + There are two types of buses, ISA and PCI, for Smartio/Industio + family multiport board. + +ISA board +--------- + + You'll have to configure CAP address, I/O address, Interrupt Vector + as well as IRQ before installing this driver. Please refer to hardware + installation procedure in User's Manual before proceed any further. + Please make sure the JP1 is open after the ISA board is set properly. + +PCI/UPCI board +-------------- + + You may need to adjust IRQ usage in BIOS to avoid from IRQ conflict + with other ISA devices. Please refer to hardware installation + procedure in User's Manual in advance. + +PCI IRQ Sharing +--------------- + + Each port within the same multiport board shares the same IRQ. Up to + 4 Moxa Smartio/Industio PCI Family multiport boards can be installed + together on one system and they can share the same IRQ. + + +3.2 Driver files +================ + + The driver file may be obtained from ftp, CD-ROM or floppy disk. The + first step, anyway, is to copy driver file "mxser.tgz" into specified + directory. e.g. /moxa. The execute commands as below:: + + # cd / + # mkdir moxa + # cd /moxa + # tar xvf /dev/fd0 + +or:: + + # cd / + # mkdir moxa + # cd /moxa + # cp /mnt/cdrom/<driver directory>/mxser.tgz . + # tar xvfz mxser.tgz + + +3.3 Device naming convention +============================ + + You may find all the driver and utilities files in /moxa/mxser. + Following installation procedure depends on the model you'd like to + run the driver. If you prefer module driver, please refer to 3.4. + If static driver is required, please refer to 3.5. + +Dialin and callout port +----------------------- + + This driver remains traditional serial device properties. There are + two special file name for each serial port. One is dial-in port + which is named "ttyMxx". For callout port, the naming convention + is "cumxx". + +Device naming when more than 2 boards installed +----------------------------------------------- + + Naming convention for each Smartio/Industio multiport board is + pre-defined as below. + + ============ =============== ============== + Board Num. Dial-in Port Callout port + 1st board ttyM0 - ttyM7 cum0 - cum7 + 2nd board ttyM8 - ttyM15 cum8 - cum15 + 3rd board ttyM16 - ttyM23 cum16 - cum23 + 4th board ttyM24 - ttym31 cum24 - cum31 + ============ =============== ============== + +.. note:: + + Under Kernel 2.6 and upper, the cum Device is Obsolete. So use ttyM* + device instead. + +Board sequence +-------------- + + This driver will activate ISA boards according to the parameter set + in the driver. After all specified ISA board activated, PCI board + will be installed in the system automatically driven. + Therefore the board number is sorted by the CAP address of ISA boards. + For PCI boards, their sequence will be after ISA boards and C168H/PCI + has higher priority than C104H/PCI boards. + +3.4 Module driver configuration +=============================== + + Module driver is easiest way to install. If you prefer static driver + installation, please skip this paragraph. + + + ------------- Prepare to use the MOXA driver -------------------- + +3.4.1 Create tty device with correct major number +------------------------------------------------- + + Before using MOXA driver, your system must have the tty devices + which are created with driver's major number. We offer one shell + script "msmknod" to simplify the procedure. + This step is only needed to be executed once. But you still + need to do this procedure when: + + a. You change the driver's major number. Please refer the "3.7" + section. + b. Your total installed MOXA boards number is changed. Maybe you + add/delete one MOXA board. + c. You want to change the tty name. This needs to modify the + shell script "msmknod" + + The procedure is:: + + # cd /moxa/mxser/driver + # ./msmknod + + This shell script will require the major number for dial-in + device and callout device to create tty device. You also need + to specify the total installed MOXA board number. Default major + numbers for dial-in device and callout device are 30, 35. If + you need to change to other number, please refer section "3.7" + for more detailed procedure. + Msmknod will delete any special files occupying the same device + naming. + +3.4.2 Build the MOXA driver and utilities +----------------------------------------- + + Before using the MOXA driver and utilities, you need compile the + all the source code. This step is only need to be executed once. + But you still re-compile the source code if you modify the source + code. For example, if you change the driver's major number (see + "3.7" section), then you need to do this step again. + + Find "Makefile" in /moxa/mxser, then run + + # make clean; make install + + ..note:: + + For Red Hat 9, Red Hat Enterprise Linux AS3/ES3/WS3 & Fedora Core1: + # make clean; make installsp1 + + For Red Hat Enterprise Linux AS4/ES4/WS4: + # make clean; make installsp2 + + The driver files "mxser.o" and utilities will be properly compiled + and copied to system directories respectively. + +------------- Load MOXA driver-------------------- + +3.4.3 Load the MOXA driver +-------------------------- + + :: + + # modprobe mxser <argument> + + will activate the module driver. You may run "lsmod" to check + if "mxser" is activated. If the MOXA board is ISA board, the + <argument> is needed. Please refer to section "3.4.5" for more + information. + +------------- Load MOXA driver on boot -------------------- + +3.4.4 Load the mxser driver +--------------------------- + + + For the above description, you may manually execute + "modprobe mxser" to activate this driver and run + "rmmod mxser" to remove it. + + However, it's better to have a boot time configuration to + eliminate manual operation. Boot time configuration can be + achieved by rc file. We offer one "rc.mxser" file to simplify + the procedure under "moxa/mxser/driver". + + But if you use ISA board, please modify the "modprobe ..." command + to add the argument (see "3.4.5" section). After modifying the + rc.mxser, please try to execute "/moxa/mxser/driver/rc.mxser" + manually to make sure the modification is ok. If any error + encountered, please try to modify again. If the modification is + completed, follow the below step. + + Run following command for setting rc files:: + + # cd /moxa/mxser/driver + # cp ./rc.mxser /etc/rc.d + # cd /etc/rc.d + + Check "rc.serial" is existed or not. If "rc.serial" doesn't exist, + create it by vi, run "chmod 755 rc.serial" to change the permission. + + Add "/etc/rc.d/rc.mxser" in last line. + + Reboot and check if moxa.o activated by "lsmod" command. + +3.4.5. specify CAP address +-------------------------- + + If you'd like to drive Smartio/Industio ISA boards in the system, + you'll have to add parameter to specify CAP address of given + board while activating "mxser.o". The format for parameters are + as follows.:: + + modprobe mxser ioaddr=0x???,0x???,0x???,0x??? + | | | | + | | | +- 4th ISA board + | | +------ 3rd ISA board + | +------------ 2nd ISA board + +-------------------1st ISA board + +3.5 Static driver configuration for Linux kernel 2.4.x and 2.6.x +================================================================ + + Note: + To use static driver, you must install the linux kernel + source package. + +3.5.1 Backup the built-in driver in the kernel +---------------------------------------------- + + :: + + # cd /usr/src/linux/drivers/char + # mv mxser.c mxser.c.old + + For Red Hat 7.x user, you need to create link: + # cd /usr/src + # ln -s linux-2.4 linux + +3.5.2 Create link +----------------- + :: + + # cd /usr/src/linux/drivers/char + # ln -s /moxa/mxser/driver/mxser.c mxser.c + +3.5.3 Add CAP address list for ISA boards. +------------------------------------------ + + For PCI boards user, please skip this step. + + In module mode, the CAP address for ISA board is given by + parameter. In static driver configuration, you'll have to + assign it within driver's source code. If you will not + install any ISA boards, you may skip to next portion. + The instructions to modify driver source code are as + below. + + a. run:: + + # cd /moxa/mxser/driver + # vi mxser.c + + b. Find the array mxserBoardCAP[] as below:: + + static int mxserBoardCAP[] = {0x00, 0x00, 0x00, 0x00}; + + c. Change the address within this array using vi. For + example, to driver 2 ISA boards with CAP address + 0x280 and 0x180 as 1st and 2nd board. Just to change + the source code as follows:: + + static int mxserBoardCAP[] = {0x280, 0x180, 0x00, 0x00}; + +3.5.4 Setup kernel configuration +-------------------------------- + + Configure the kernel:: + + # cd /usr/src/linux + # make menuconfig + + You will go into a menu-driven system. Please select [Character + devices][Non-standard serial port support], enable the [Moxa + SmartIO support] driver with "[*]" for built-in (not "[M]"), then + select [Exit] to exit this program. + +3.5.5 Rebuild kernel +-------------------- + + The following are for Linux kernel rebuilding, for your + reference only. + + For appropriate details, please refer to the Linux document: + + a. Run the following commands:: + + cd /usr/src/linux + make clean # take a few minutes + make dep # take a few minutes + make bzImage # take probably 10-20 minutes + make install # copy boot image to correct position + + f. Please make sure the boot kernel (vmlinuz) is in the + correct position. + g. If you use 'lilo' utility, you should check /etc/lilo.conf + 'image' item specified the path which is the 'vmlinuz' path, + or you will load wrong (or old) boot kernel image (vmlinuz). + After checking /etc/lilo.conf, please run "lilo". + + Note that if the result of "make bzImage" is ERROR, then you have to + go back to Linux configuration Setup. Type "make menuconfig" in + directory /usr/src/linux. + + +3.5.6 Make tty device and special file +-------------------------------------- + + :: + # cd /moxa/mxser/driver + # ./msmknod + +3.5.7 Make utility +------------------ + + :: + + # cd /moxa/mxser/utility + # make clean; make install + +3.5.8 Reboot +------------ + + + +3.6 Custom configuration +======================== + + Although this driver already provides you default configuration, you + still can change the device name and major number. The instruction to + change these parameters are shown as below. + +a. Change Device name + + If you'd like to use other device names instead of default naming + convention, all you have to do is to modify the internal code + within the shell script "msmknod". First, you have to open "msmknod" + by vi. Locate each line contains "ttyM" and "cum" and change them + to the device name you desired. "msmknod" creates the device names + you need next time executed. + +b. Change Major number + + If major number 30 and 35 had been occupied, you may have to select + 2 free major numbers for this driver. There are 3 steps to change + major numbers. + +3.6.1 Find free major numbers +----------------------------- + + In /proc/devices, you may find all the major numbers occupied + in the system. Please select 2 major numbers that are available. + e.g. 40, 45. + +3.6.2 Create special files +-------------------------- + + Run /moxa/mxser/driver/msmknod to create special files with + specified major numbers. + +3.6.3 Modify driver with new major number +----------------------------------------- + + Run vi to open /moxa/mxser/driver/mxser.c. Locate the line + contains "MXSERMAJOR". Change the content as below:: + + #define MXSERMAJOR 40 + #define MXSERCUMAJOR 45 + + 3.6.4 Run "make clean; make install" in /moxa/mxser/driver. + +3.7 Verify driver installation +============================== + + You may refer to /var/log/messages to check the latest status + log reported by this driver whenever it's activated. + +4. Utilities +^^^^^^^^^^^^ + + There are 3 utilities contained in this driver. They are msdiag, msmon and + msterm. These 3 utilities are released in form of source code. They should + be compiled into executable file and copied into /usr/bin. + + Before using these utilities, please load driver (refer 3.4 & 3.5) and + make sure you had run the "msmknod" utility. + +msdiag - Diagnostic +=================== + + This utility provides the function to display what Moxa Smartio/Industio + board found by driver in the system. + +msmon - Port Monitoring +======================= + + This utility gives the user a quick view about all the MOXA ports' + activities. One can easily learn each port's total received/transmitted + (Rx/Tx) character count since the time when the monitoring is started. + + Rx/Tx throughputs per second are also reported in interval basis (e.g. + the last 5 seconds) and in average basis (since the time the monitoring + is started). You can reset all ports' count by <HOME> key. <+> <-> + (plus/minus) keys to change the displaying time interval. Press <ENTER> + on the port, that cursor stay, to view the port's communication + parameters, signal status, and input/output queue. + +msterm - Terminal Emulation +=========================== + + This utility provides data sending and receiving ability of all tty ports, + especially for MOXA ports. It is quite useful for testing simple + application, for example, sending AT command to a modem connected to the + port or used as a terminal for login purpose. Note that this is only a + dumb terminal emulation without handling full screen operation. + +5. Setserial +^^^^^^^^^^^^ + + Supported Setserial parameters are listed as below. + + ============== ========================================================= + uart set UART type(16450-->disable FIFO, 16550A-->enable FIFO) + close_delay set the amount of time(in 1/100 of a second) that DTR + should be kept low while being closed. + closing_wait set the amount of time(in 1/100 of a second) that the + serial port should wait for data to be drained while + being closed, before the receiver is disable. + spd_hi Use 57.6kb when the application requests 38.4kb. + spd_vhi Use 115.2kb when the application requests 38.4kb. + spd_shi Use 230.4kb when the application requests 38.4kb. + spd_warp Use 460.8kb when the application requests 38.4kb. + spd_normal Use 38.4kb when the application requests 38.4kb. + spd_cust Use the custom divisor to set the speed when the + application requests 38.4kb. + divisor This option set the custom division. + baud_base This option set the base baud rate. + ============== ========================================================= + +6. Troubleshooting +^^^^^^^^^^^^^^^^^^ + + The boot time error messages and solutions are stated as clearly as + possible. If all the possible solutions fail, please contact our technical + support team to get more help. + + + Error msg: + More than 4 Moxa Smartio/Industio family boards found. Fifth board + and after are ignored. + + Solution: + To avoid this problem, please unplug fifth and after board, because Moxa + driver supports up to 4 boards. + + Error msg: + Request_irq fail, IRQ(?) may be conflict with another device. + + Solution: + Other PCI or ISA devices occupy the assigned IRQ. If you are not sure + which device causes the situation, please check /proc/interrupts to find + free IRQ and simply change another free IRQ for Moxa board. + + Error msg: + Board #: C1xx Series(CAP=xxx) interrupt number invalid. + + Solution: + Each port within the same multiport board shares the same IRQ. Please set + one IRQ (IRQ doesn't equal to zero) for one Moxa board. + + Error msg: + No interrupt vector be set for Moxa ISA board(CAP=xxx). + + Solution: + Moxa ISA board needs an interrupt vector.Please refer to user's manual + "Hardware Installation" chapter to set interrupt vector. + + Error msg: + Couldn't install MOXA Smartio/Industio family driver! + + Solution: + Load Moxa driver fail, the major number may conflict with other devices. + Please refer to previous section 3.7 to change a free major number for + Moxa driver. + + Error msg: + Couldn't install MOXA Smartio/Industio family callout driver! + + Solution: + Load Moxa callout driver fail, the callout device major number may + conflict with other devices. Please refer to previous section 3.7 to + change a free callout device major number for Moxa driver. |