diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/hwmon/sht15.rst | |
parent | Initial commit. (diff) | |
download | linux-upstream/5.10.209.tar.xz linux-upstream/5.10.209.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'Documentation/hwmon/sht15.rst')
-rw-r--r-- | Documentation/hwmon/sht15.rst | 83 |
1 files changed, 83 insertions, 0 deletions
diff --git a/Documentation/hwmon/sht15.rst b/Documentation/hwmon/sht15.rst new file mode 100644 index 000000000..485abe037 --- /dev/null +++ b/Documentation/hwmon/sht15.rst @@ -0,0 +1,83 @@ +Kernel driver sht15 +=================== + +Authors: + + * Wouter Horre + * Jonathan Cameron + * Vivien Didelot <vivien.didelot@savoirfairelinux.com> + * Jerome Oufella <jerome.oufella@savoirfairelinux.com> + +Supported chips: + + * Sensirion SHT10 + + Prefix: 'sht10' + + * Sensirion SHT11 + + Prefix: 'sht11' + + * Sensirion SHT15 + + Prefix: 'sht15' + + * Sensirion SHT71 + + Prefix: 'sht71' + + * Sensirion SHT75 + + Prefix: 'sht75' + +Datasheet: Publicly available at the Sensirion website + + http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf + +Description +----------- + +The SHT10, SHT11, SHT15, SHT71, and SHT75 are humidity and temperature +sensors. + +The devices communicate using two GPIO lines. + +Supported resolutions for the measurements are 14 bits for temperature and 12 +bits for humidity, or 12 bits for temperature and 8 bits for humidity. + +The humidity calibration coefficients are programmed into an OTP memory on the +chip. These coefficients are used to internally calibrate the signals from the +sensors. Disabling the reload of those coefficients allows saving 10ms for each +measurement and decrease power consumption, while losing on precision. + +Some options may be set via sysfs attributes. + +Notes: + * The regulator supply name is set to "vcc". + * If a CRC validation fails, a soft reset command is sent, which resets + status register to its hardware default value, but the driver will try to + restore the previous device configuration. + +Platform data +------------- + +* checksum: + set it to true to enable CRC validation of the readings (default to false). +* no_otp_reload: + flag to indicate not to reload from OTP (default to false). +* low_resolution: + flag to indicate the temp/humidity resolution to use (default to false). + +Sysfs interface +--------------- + +================== ========================================================== +temp1_input temperature input +humidity1_input humidity input +heater_enable write 1 in this attribute to enable the on-chip heater, + 0 to disable it. Be careful not to enable the heater + for too long. +temp1_fault if 1, this means that the voltage is low (below 2.47V) and + measurement may be invalid. +humidity1_fault same as temp1_fault. +================== ========================================================== |