diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/hwmon/sysfs-interface.rst | |
parent | Initial commit. (diff) | |
download | linux-430c2fc249ea5c0536abd21c23382884005c9093.tar.xz linux-430c2fc249ea5c0536abd21c23382884005c9093.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'Documentation/hwmon/sysfs-interface.rst')
-rw-r--r-- | Documentation/hwmon/sysfs-interface.rst | 1156 |
1 files changed, 1156 insertions, 0 deletions
diff --git a/Documentation/hwmon/sysfs-interface.rst b/Documentation/hwmon/sysfs-interface.rst new file mode 100644 index 000000000..678c9c60b --- /dev/null +++ b/Documentation/hwmon/sysfs-interface.rst @@ -0,0 +1,1156 @@ +Naming and data format standards for sysfs files +================================================ + +The libsensors library offers an interface to the raw sensors data +through the sysfs interface. Since lm-sensors 3.0.0, libsensors is +completely chip-independent. It assumes that all the kernel drivers +implement the standard sysfs interface described in this document. +This makes adding or updating support for any given chip very easy, as +libsensors, and applications using it, do not need to be modified. +This is a major improvement compared to lm-sensors 2. + +Note that motherboards vary widely in the connections to sensor chips. +There is no standard that ensures, for example, that the second +temperature sensor is connected to the CPU, or that the second fan is on +the CPU. Also, some values reported by the chips need some computation +before they make full sense. For example, most chips can only measure +voltages between 0 and +4V. Other voltages are scaled back into that +range using external resistors. Since the values of these resistors +can change from motherboard to motherboard, the conversions cannot be +hard coded into the driver and have to be done in user space. + +For this reason, even if we aim at a chip-independent libsensors, it will +still require a configuration file (e.g. /etc/sensors.conf) for proper +values conversion, labeling of inputs and hiding of unused inputs. + +An alternative method that some programs use is to access the sysfs +files directly. This document briefly describes the standards that the +drivers follow, so that an application program can scan for entries and +access this data in a simple and consistent way. That said, such programs +will have to implement conversion, labeling and hiding of inputs. For +this reason, it is still not recommended to bypass the library. + +Each chip gets its own directory in the sysfs /sys/devices tree. To +find all sensor chips, it is easier to follow the device symlinks from +`/sys/class/hwmon/hwmon*`. + +Up to lm-sensors 3.0.0, libsensors looks for hardware monitoring attributes +in the "physical" device directory. Since lm-sensors 3.0.1, attributes found +in the hwmon "class" device directory are also supported. Complex drivers +(e.g. drivers for multifunction chips) may want to use this possibility to +avoid namespace pollution. The only drawback will be that older versions of +libsensors won't support the driver in question. + +All sysfs values are fixed point numbers. + +There is only one value per file, unlike the older /proc specification. +The common scheme for files naming is: <type><number>_<item>. Usual +types for sensor chips are "in" (voltage), "temp" (temperature) and +"fan" (fan). Usual items are "input" (measured value), "max" (high +threshold, "min" (low threshold). Numbering usually starts from 1, +except for voltages which start from 0 (because most data sheets use +this). A number is always used for elements that can be present more +than once, even if there is a single element of the given type on the +specific chip. Other files do not refer to a specific element, so +they have a simple name, and no number. + +Alarms are direct indications read from the chips. The drivers do NOT +make comparisons of readings to thresholds. This allows violations +between readings to be caught and alarmed. The exact definition of an +alarm (for example, whether a threshold must be met or must be exceeded +to cause an alarm) is chip-dependent. + +When setting values of hwmon sysfs attributes, the string representation of +the desired value must be written, note that strings which are not a number +are interpreted as 0! For more on how written strings are interpreted see the +"sysfs attribute writes interpretation" section at the end of this file. + +------------------------------------------------------------------------- + +======= =========================================== +`[0-*]` denotes any positive number starting from 0 +`[1-*]` denotes any positive number starting from 1 +RO read only value +WO write only value +RW read/write value +======= =========================================== + +Read/write values may be read-only for some chips, depending on the +hardware implementation. + +All entries (except name) are optional, and should only be created in a +given driver if the chip has the feature. + + +***************** +Global attributes +***************** + +`name` + The chip name. + This should be a short, lowercase string, not containing + whitespace, dashes, or the wildcard character '*'. + This attribute represents the chip name. It is the only + mandatory attribute. + I2C devices get this attribute created automatically. + + RO + +`update_interval` + The interval at which the chip will update readings. + Unit: millisecond + + RW + + Some devices have a variable update rate or interval. + This attribute can be used to change it to the desired value. + + +******** +Voltages +******** + +`in[0-*]_min` + Voltage min value. + + Unit: millivolt + + RW + +`in[0-*]_lcrit` + Voltage critical min value. + + Unit: millivolt + + RW + + If voltage drops to or below this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + +`in[0-*]_max` + Voltage max value. + + Unit: millivolt + + RW + +`in[0-*]_crit` + Voltage critical max value. + + Unit: millivolt + + RW + + If voltage reaches or exceeds this limit, the system may + take drastic action such as power down or reset. At the very + least, it should report a fault. + +`in[0-*]_input` + Voltage input value. + + Unit: millivolt + + RO + + Voltage measured on the chip pin. + + Actual voltage depends on the scaling resistors on the + motherboard, as recommended in the chip datasheet. + + This varies by chip and by motherboard. + Because of this variation, values are generally NOT scaled + by the chip driver, and must be done by the application. + However, some drivers (notably lm87 and via686a) + do scale, because of internal resistors built into a chip. + These drivers will output the actual voltage. Rule of + thumb: drivers should report the voltage values at the + "pins" of the chip. + +`in[0-*]_average` + Average voltage + + Unit: millivolt + + RO + +`in[0-*]_lowest` + Historical minimum voltage + + Unit: millivolt + + RO + +`in[0-*]_highest` + Historical maximum voltage + + Unit: millivolt + + RO + +`in[0-*]_reset_history` + Reset inX_lowest and inX_highest + + WO + +`in_reset_history` + Reset inX_lowest and inX_highest for all sensors + + WO + +`in[0-*]_label` + Suggested voltage channel label. + + Text string + + Should only be created if the driver has hints about what + this voltage channel is being used for, and user-space + doesn't. In all other cases, the label is provided by + user-space. + + RO + +`in[0-*]_enable` + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +`cpu[0-*]_vid` + CPU core reference voltage. + + Unit: millivolt + + RO + + Not always correct. + +`vrm` + Voltage Regulator Module version number. + + RW (but changing it should no more be necessary) + + Originally the VRM standard version multiplied by 10, but now + an arbitrary number, as not all standards have a version + number. + + Affects the way the driver calculates the CPU core reference + voltage from the vid pins. + +`in[0-*]_rated_min` + Minimum rated voltage. + + Unit: millivolt + + RO + +`in[0-*]_rated_max` + Maximum rated voltage. + + Unit: millivolt + + RO + +Also see the Alarms section for status flags associated with voltages. + + +**** +Fans +**** + +`fan[1-*]_min` + Fan minimum value + + Unit: revolution/min (RPM) + + RW + +`fan[1-*]_max` + Fan maximum value + + Unit: revolution/min (RPM) + + Only rarely supported by the hardware. + RW + +`fan[1-*]_input` + Fan input value. + + Unit: revolution/min (RPM) + + RO + +`fan[1-*]_div` + Fan divisor. + + Integer value in powers of two (1, 2, 4, 8, 16, 32, 64, 128). + + RW + + Some chips only support values 1, 2, 4 and 8. + Note that this is actually an internal clock divisor, which + affects the measurable speed range, not the read value. + +`fan[1-*]_pulses` + Number of tachometer pulses per fan revolution. + + Integer value, typically between 1 and 4. + + RW + + This value is a characteristic of the fan connected to the + device's input, so it has to be set in accordance with the fan + model. + + Should only be created if the chip has a register to configure + the number of pulses. In the absence of such a register (and + thus attribute) the value assumed by all devices is 2 pulses + per fan revolution. + +`fan[1-*]_target` + Desired fan speed + + Unit: revolution/min (RPM) + + RW + + Only makes sense if the chip supports closed-loop fan speed + control based on the measured fan speed. + +`fan[1-*]_label` + Suggested fan channel label. + + Text string + + Should only be created if the driver has hints about what + this fan channel is being used for, and user-space doesn't. + In all other cases, the label is provided by user-space. + + RO + +`fan[1-*]_enable` + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +Also see the Alarms section for status flags associated with fans. + + +*** +PWM +*** + +`pwm[1-*]` + Pulse width modulation fan control. + + Integer value in the range 0 to 255 + + RW + + 255 is max or 100%. + +`pwm[1-*]_enable` + Fan speed control method: + + - 0: no fan speed control (i.e. fan at full speed) + - 1: manual fan speed control enabled (using `pwm[1-*]`) + - 2+: automatic fan speed control enabled + + Check individual chip documentation files for automatic mode + details. + + RW + +`pwm[1-*]_mode` + - 0: DC mode (direct current) + - 1: PWM mode (pulse-width modulation) + + RW + +`pwm[1-*]_freq` + Base PWM frequency in Hz. + + Only possibly available when pwmN_mode is PWM, but not always + present even then. + + RW + +`pwm[1-*]_auto_channels_temp` + Select which temperature channels affect this PWM output in + auto mode. + + Bitfield, 1 is temp1, 2 is temp2, 4 is temp3 etc... + Which values are possible depend on the chip used. + + RW + +`pwm[1-*]_auto_point[1-*]_pwm` / `pwm[1-*]_auto_point[1-*]_temp` / `pwm[1-*]_auto_point[1-*]_temp_hyst` + Define the PWM vs temperature curve. + + Number of trip points is chip-dependent. Use this for chips + which associate trip points to PWM output channels. + + RW + +`temp[1-*]_auto_point[1-*]_pwm` / `temp[1-*]_auto_point[1-*]_temp` / `temp[1-*]_auto_point[1-*]_temp_hyst` + Define the PWM vs temperature curve. + + Number of trip points is chip-dependent. Use this for chips + which associate trip points to temperature channels. + + RW + +There is a third case where trip points are associated to both PWM output +channels and temperature channels: the PWM values are associated to PWM +output channels while the temperature values are associated to temperature +channels. In that case, the result is determined by the mapping between +temperature inputs and PWM outputs. When several temperature inputs are +mapped to a given PWM output, this leads to several candidate PWM values. +The actual result is up to the chip, but in general the highest candidate +value (fastest fan speed) wins. + + +************ +Temperatures +************ + +`temp[1-*]_type` + Sensor type selection. + + Integers 1 to 6 + + RW + + - 1: CPU embedded diode + - 2: 3904 transistor + - 3: thermal diode + - 4: thermistor + - 5: AMD AMDSI + - 6: Intel PECI + + Not all types are supported by all chips + +`temp[1-*]_max` + Temperature max value. + + Unit: millidegree Celsius (or millivolt, see below) + + RW + +`temp[1-*]_min` + Temperature min value. + + Unit: millidegree Celsius + + RW + +`temp[1-*]_max_hyst` + Temperature hysteresis value for max limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the max value. + + RW + +`temp[1-*]_min_hyst` + Temperature hysteresis value for min limit. + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the min value. + + RW + +`temp[1-*]_input` + Temperature input value. + + Unit: millidegree Celsius + + RO + +`temp[1-*]_crit` + Temperature critical max value, typically greater than + corresponding temp_max values. + + Unit: millidegree Celsius + + RW + +`temp[1-*]_crit_hyst` + Temperature hysteresis value for critical limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the critical value. + + RW + +`temp[1-*]_emergency` + Temperature emergency max value, for chips supporting more than + two upper temperature limits. Must be equal or greater than + corresponding temp_crit values. + + Unit: millidegree Celsius + + RW + +`temp[1-*]_emergency_hyst` + Temperature hysteresis value for emergency limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the emergency value. + + RW + +`temp[1-*]_lcrit` + Temperature critical min value, typically lower than + corresponding temp_min values. + + Unit: millidegree Celsius + + RW + +`temp[1-*]_lcrit_hyst` + Temperature hysteresis value for critical min limit. + + Unit: millidegree Celsius + + Must be reported as an absolute temperature, NOT a delta + from the critical min value. + + RW + +`temp[1-*]_offset` + Temperature offset which is added to the temperature reading + by the chip. + + Unit: millidegree Celsius + + Read/Write value. + +`temp[1-*]_label` + Suggested temperature channel label. + + Text string + + Should only be created if the driver has hints about what + this temperature channel is being used for, and user-space + doesn't. In all other cases, the label is provided by + user-space. + + RO + +`temp[1-*]_lowest` + Historical minimum temperature + + Unit: millidegree Celsius + + RO + +`temp[1-*]_highest` + Historical maximum temperature + + Unit: millidegree Celsius + + RO + +`temp[1-*]_reset_history` + Reset temp_lowest and temp_highest + + WO + +`temp_reset_history` + Reset temp_lowest and temp_highest for all sensors + + WO + +`temp[1-*]_enable` + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +`temp[1-*]_rated_min` + Minimum rated temperature. + + Unit: millidegree Celsius + + RO + +`temp[1-*]_rated_max` + Maximum rated temperature. + + Unit: millidegree Celsius + + RO + +Some chips measure temperature using external thermistors and an ADC, and +report the temperature measurement as a voltage. Converting this voltage +back to a temperature (or the other way around for limits) requires +mathematical functions not available in the kernel, so the conversion +must occur in user space. For these chips, all temp* files described +above should contain values expressed in millivolt instead of millidegree +Celsius. In other words, such temperature channels are handled as voltage +channels by the driver. + +Also see the Alarms section for status flags associated with temperatures. + + +******** +Currents +******** + +`curr[1-*]_max` + Current max value + + Unit: milliampere + + RW + +`curr[1-*]_min` + Current min value. + + Unit: milliampere + + RW + +`curr[1-*]_lcrit` + Current critical low value + + Unit: milliampere + + RW + +`curr[1-*]_crit` + Current critical high value. + + Unit: milliampere + + RW + +`curr[1-*]_input` + Current input value + + Unit: milliampere + + RO + +`curr[1-*]_average` + Average current use + + Unit: milliampere + + RO + +`curr[1-*]_lowest` + Historical minimum current + + Unit: milliampere + + RO + +`curr[1-*]_highest` + Historical maximum current + Unit: milliampere + RO + +`curr[1-*]_reset_history` + Reset currX_lowest and currX_highest + + WO + +`curr_reset_history` + Reset currX_lowest and currX_highest for all sensors + + WO + +`curr[1-*]_enable` + Enable or disable the sensors. + + When disabled the sensor read will return -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +`curr[1-*]_rated_min` + Minimum rated current. + + Unit: milliampere + + RO + +`curr[1-*]_rated_max` + Maximum rated current. + + Unit: milliampere + + RO + +Also see the Alarms section for status flags associated with currents. + +***** +Power +***** + +`power[1-*]_average` + Average power use + + Unit: microWatt + + RO + +`power[1-*]_average_interval` + Power use averaging interval. A poll + notification is sent to this file if the + hardware changes the averaging interval. + + Unit: milliseconds + + RW + +`power[1-*]_average_interval_max` + Maximum power use averaging interval + + Unit: milliseconds + + RO + +`power[1-*]_average_interval_min` + Minimum power use averaging interval + + Unit: milliseconds + + RO + +`power[1-*]_average_highest` + Historical average maximum power use + + Unit: microWatt + + RO + +`power[1-*]_average_lowest` + Historical average minimum power use + + Unit: microWatt + + RO + +`power[1-*]_average_max` + A poll notification is sent to + `power[1-*]_average` when power use + rises above this value. + + Unit: microWatt + + RW + +`power[1-*]_average_min` + A poll notification is sent to + `power[1-*]_average` when power use + sinks below this value. + + Unit: microWatt + + RW + +`power[1-*]_input` + Instantaneous power use + + Unit: microWatt + + RO + +`power[1-*]_input_highest` + Historical maximum power use + + Unit: microWatt + + RO + +`power[1-*]_input_lowest` + Historical minimum power use + + Unit: microWatt + + RO + +`power[1-*]_reset_history` + Reset input_highest, input_lowest, + average_highest and average_lowest. + + WO + +`power[1-*]_accuracy` + Accuracy of the power meter. + + Unit: Percent + + RO + +`power[1-*]_cap` + If power use rises above this limit, the + system should take action to reduce power use. + A poll notification is sent to this file if the + cap is changed by the hardware. The `*_cap` + files only appear if the cap is known to be + enforced by hardware. + + Unit: microWatt + + RW + +`power[1-*]_cap_hyst` + Margin of hysteresis built around capping and + notification. + + Unit: microWatt + + RW + +`power[1-*]_cap_max` + Maximum cap that can be set. + + Unit: microWatt + + RO + +`power[1-*]_cap_min` + Minimum cap that can be set. + + Unit: microWatt + + RO + +`power[1-*]_max` + Maximum power. + + Unit: microWatt + + RW + +`power[1-*]_crit` + Critical maximum power. + + If power rises to or above this limit, the + system is expected take drastic action to reduce + power consumption, such as a system shutdown or + a forced powerdown of some devices. + + Unit: microWatt + + RW + +`power[1-*]_enable` + Enable or disable the sensors. + + When disabled the sensor read will return + -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +`power[1-*]_rated_min` + Minimum rated power. + + Unit: microWatt + + RO + +`power[1-*]_rated_max` + Maximum rated power. + + Unit: microWatt + + RO + +Also see the Alarms section for status flags associated with power readings. + +****** +Energy +****** + +`energy[1-*]_input` + Cumulative energy use + + Unit: microJoule + + RO + +`energy[1-*]_enable` + Enable or disable the sensors. + + When disabled the sensor read will return + -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +******** +Humidity +******** + +`humidity[1-*]_input` + Humidity + + Unit: milli-percent (per cent mille, pcm) + + RO + + +`humidity[1-*]_enable` + Enable or disable the sensors + + When disabled the sensor read will return + -ENODATA. + + - 1: Enable + - 0: Disable + + RW + +`humidity[1-*]_rated_min` + Minimum rated humidity. + + Unit: milli-percent (per cent mille, pcm) + + RO + +`humidity[1-*]_rated_max` + Maximum rated humidity. + + Unit: milli-percent (per cent mille, pcm) + + RO + +****** +Alarms +****** + +Each channel or limit may have an associated alarm file, containing a +boolean value. 1 means than an alarm condition exists, 0 means no alarm. + +Usually a given chip will either use channel-related alarms, or +limit-related alarms, not both. The driver should just reflect the hardware +implementation. + ++-------------------------------+-----------------------+ +| **`in[0-*]_alarm`, | Channel alarm | +| `curr[1-*]_alarm`, | | +| `power[1-*]_alarm`, | - 0: no alarm | +| `fan[1-*]_alarm`, | - 1: alarm | +| `temp[1-*]_alarm`** | | +| | RO | ++-------------------------------+-----------------------+ + +**OR** + ++-------------------------------+-----------------------+ +| **`in[0-*]_min_alarm`, | Limit alarm | +| `in[0-*]_max_alarm`, | | +| `in[0-*]_lcrit_alarm`, | - 0: no alarm | +| `in[0-*]_crit_alarm`, | - 1: alarm | +| `curr[1-*]_min_alarm`, | | +| `curr[1-*]_max_alarm`, | RO | +| `curr[1-*]_lcrit_alarm`, | | +| `curr[1-*]_crit_alarm`, | | +| `power[1-*]_cap_alarm`, | | +| `power[1-*]_max_alarm`, | | +| `power[1-*]_crit_alarm`, | | +| `fan[1-*]_min_alarm`, | | +| `fan[1-*]_max_alarm`, | | +| `temp[1-*]_min_alarm`, | | +| `temp[1-*]_max_alarm`, | | +| `temp[1-*]_lcrit_alarm`, | | +| `temp[1-*]_crit_alarm`, | | +| `temp[1-*]_emergency_alarm`** | | ++-------------------------------+-----------------------+ + +Each input channel may have an associated fault file. This can be used +to notify open diodes, unconnected fans etc. where the hardware +supports it. When this boolean has value 1, the measurement for that +channel should not be trusted. + +`fan[1-*]_fault` / `temp[1-*]_fault` + Input fault condition + + - 0: no fault occurred + - 1: fault condition + + RO + +Some chips also offer the possibility to get beeped when an alarm occurs: + +`beep_enable` + Master beep enable + + - 0: no beeps + - 1: beeps + + RW + +`in[0-*]_beep`, `curr[1-*]_beep`, `fan[1-*]_beep`, `temp[1-*]_beep`, + Channel beep + + - 0: disable + - 1: enable + + RW + +In theory, a chip could provide per-limit beep masking, but no such chip +was seen so far. + +Old drivers provided a different, non-standard interface to alarms and +beeps. These interface files are deprecated, but will be kept around +for compatibility reasons: + +`alarms` + Alarm bitmask. + + RO + + Integer representation of one to four bytes. + + A '1' bit means an alarm. + + Chips should be programmed for 'comparator' mode so that + the alarm will 'come back' after you read the register + if it is still valid. + + Generally a direct representation of a chip's internal + alarm registers; there is no standard for the position + of individual bits. For this reason, the use of this + interface file for new drivers is discouraged. Use + `individual *_alarm` and `*_fault` files instead. + Bits are defined in kernel/include/sensors.h. + +`beep_mask` + Bitmask for beep. + Same format as 'alarms' with the same bit locations, + use discouraged for the same reason. Use individual + `*_beep` files instead. + RW + + +******************* +Intrusion detection +******************* + +`intrusion[0-*]_alarm` + Chassis intrusion detection + + - 0: OK + - 1: intrusion detected + + RW + + Contrary to regular alarm flags which clear themselves + automatically when read, this one sticks until cleared by + the user. This is done by writing 0 to the file. Writing + other values is unsupported. + +`intrusion[0-*]_beep` + Chassis intrusion beep + + 0: disable + 1: enable + + RW + +**************************** +Average sample configuration +**************************** + +Devices allowing for reading {in,power,curr,temp}_average values may export +attributes for controlling number of samples used to compute average. + ++--------------+---------------------------------------------------------------+ +| samples | Sets number of average samples for all types of measurements. | +| | | +| | RW | ++--------------+---------------------------------------------------------------+ +| in_samples | Sets number of average samples for specific type of | +| power_samples| measurements. | +| curr_samples | | +| temp_samples | Note that on some devices it won't be possible to set all of | +| | them to different values so changing one might also change | +| | some others. | +| | | +| | RW | ++--------------+---------------------------------------------------------------+ + +sysfs attribute writes interpretation +------------------------------------- + +hwmon sysfs attributes always contain numbers, so the first thing to do is to +convert the input to a number, there are 2 ways todo this depending whether +the number can be negative or not:: + + unsigned long u = simple_strtoul(buf, NULL, 10); + long s = simple_strtol(buf, NULL, 10); + +With buf being the buffer with the user input being passed by the kernel. +Notice that we do not use the second argument of strto[u]l, and thus cannot +tell when 0 is returned, if this was really 0 or is caused by invalid input. +This is done deliberately as checking this everywhere would add a lot of +code to the kernel. + +Notice that it is important to always store the converted value in an +unsigned long or long, so that no wrap around can happen before any further +checking. + +After the input string is converted to an (unsigned) long, the value should be +checked if its acceptable. Be careful with further conversions on the value +before checking it for validity, as these conversions could still cause a wrap +around before the check. For example do not multiply the result, and only +add/subtract if it has been divided before the add/subtract. + +What to do if a value is found to be invalid, depends on the type of the +sysfs attribute that is being set. If it is a continuous setting like a +tempX_max or inX_max attribute, then the value should be clamped to its +limits using clamp_val(value, min_limit, max_limit). If it is not continuous +like for example a tempX_type, then when an invalid value is written, +-EINVAL should be returned. + +Example1, temp1_max, register is a signed 8 bit value (-128 - 127 degrees):: + + long v = simple_strtol(buf, NULL, 10) / 1000; + v = clamp_val(v, -128, 127); + /* write v to register */ + +Example2, fan divider setting, valid values 2, 4 and 8:: + + unsigned long v = simple_strtoul(buf, NULL, 10); + + switch (v) { + case 2: v = 1; break; + case 4: v = 2; break; + case 8: v = 3; break; + default: + return -EINVAL; + } + /* write v to register */ |