diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/networking/batman-adv.rst | |
parent | Initial commit. (diff) | |
download | linux-5d1646d90e1f2cceb9f0828f4b28318cd0ec7744.tar.xz linux-5d1646d90e1f2cceb9f0828f4b28318cd0ec7744.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to '')
-rw-r--r-- | Documentation/networking/batman-adv.rst | 168 |
1 files changed, 168 insertions, 0 deletions
diff --git a/Documentation/networking/batman-adv.rst b/Documentation/networking/batman-adv.rst new file mode 100644 index 000000000..74821d29a --- /dev/null +++ b/Documentation/networking/batman-adv.rst @@ -0,0 +1,168 @@ +.. SPDX-License-Identifier: GPL-2.0 + +========== +batman-adv +========== + +Batman advanced is a new approach to wireless networking which does no longer +operate on the IP basis. Unlike the batman daemon, which exchanges information +using UDP packets and sets routing tables, batman-advanced operates on ISO/OSI +Layer 2 only and uses and routes (or better: bridges) Ethernet Frames. It +emulates a virtual network switch of all nodes participating. Therefore all +nodes appear to be link local, thus all higher operating protocols won't be +affected by any changes within the network. You can run almost any protocol +above batman advanced, prominent examples are: IPv4, IPv6, DHCP, IPX. + +Batman advanced was implemented as a Linux kernel driver to reduce the overhead +to a minimum. It does not depend on any (other) network driver, and can be used +on wifi as well as ethernet lan, vpn, etc ... (anything with ethernet-style +layer 2). + + +Configuration +============= + +Load the batman-adv module into your kernel:: + + $ insmod batman-adv.ko + +The module is now waiting for activation. You must add some interfaces on which +batman-adv can operate. The batman-adv soft-interface can be created using the +iproute2 tool ``ip``:: + + $ ip link add name bat0 type batadv + +To activate a given interface simply attach it to the ``bat0`` interface:: + + $ ip link set dev eth0 master bat0 + +Repeat this step for all interfaces you wish to add. Now batman-adv starts +using/broadcasting on this/these interface(s). + +To deactivate an interface you have to detach it from the "bat0" interface:: + + $ ip link set dev eth0 nomaster + +The same can also be done using the batctl interface subcommand:: + + batctl -m bat0 interface create + batctl -m bat0 interface add -M eth0 + +To detach eth0 and destroy bat0:: + + batctl -m bat0 interface del -M eth0 + batctl -m bat0 interface destroy + +There are additional settings for each batadv mesh interface, vlan and hardif +which can be modified using batctl. Detailed information about this can be found +in its manual. + +For instance, you can check the current originator interval (value +in milliseconds which determines how often batman-adv sends its broadcast +packets):: + + $ batctl -M bat0 orig_interval + 1000 + +and also change its value:: + + $ batctl -M bat0 orig_interval 3000 + +In very mobile scenarios, you might want to adjust the originator interval to a +lower value. This will make the mesh more responsive to topology changes, but +will also increase the overhead. + +Information about the current state can be accessed via the batadv generic +netlink family. batctl provides a human readable version via its debug tables +subcommands. + + +Usage +===== + +To make use of your newly created mesh, batman advanced provides a new +interface "bat0" which you should use from this point on. All interfaces added +to batman advanced are not relevant any longer because batman handles them for +you. Basically, one "hands over" the data by using the batman interface and +batman will make sure it reaches its destination. + +The "bat0" interface can be used like any other regular interface. It needs an +IP address which can be either statically configured or dynamically (by using +DHCP or similar services):: + + NodeA: ip link set up dev bat0 + NodeA: ip addr add 192.168.0.1/24 dev bat0 + + NodeB: ip link set up dev bat0 + NodeB: ip addr add 192.168.0.2/24 dev bat0 + NodeB: ping 192.168.0.1 + +Note: In order to avoid problems remove all IP addresses previously assigned to +interfaces now used by batman advanced, e.g.:: + + $ ip addr flush dev eth0 + + +Logging/Debugging +================= + +All error messages, warnings and information messages are sent to the kernel +log. Depending on your operating system distribution this can be read in one of +a number of ways. Try using the commands: ``dmesg``, ``logread``, or looking in +the files ``/var/log/kern.log`` or ``/var/log/syslog``. All batman-adv messages +are prefixed with "batman-adv:" So to see just these messages try:: + + $ dmesg | grep batman-adv + +When investigating problems with your mesh network, it is sometimes necessary to +see more detailed debug messages. This must be enabled when compiling the +batman-adv module. When building batman-adv as part of the kernel, use "make +menuconfig" and enable the option ``B.A.T.M.A.N. debugging`` +(``CONFIG_BATMAN_ADV_DEBUG=y``). + +Those additional debug messages can be accessed using the perf infrastructure:: + + $ trace-cmd stream -e batadv:batadv_dbg + +The additional debug output is by default disabled. It can be enabled during +run time:: + + $ batctl -m bat0 loglevel routes tt + +will enable debug messages for when routes and translation table entries change. + +Counters for different types of packets entering and leaving the batman-adv +module are available through ethtool:: + + $ ethtool --statistics bat0 + + +batctl +====== + +As batman advanced operates on layer 2, all hosts participating in the virtual +switch are completely transparent for all protocols above layer 2. Therefore +the common diagnosis tools do not work as expected. To overcome these problems, +batctl was created. At the moment the batctl contains ping, traceroute, tcpdump +and interfaces to the kernel module settings. + +For more information, please see the manpage (``man batctl``). + +batctl is available on https://www.open-mesh.org/ + + +Contact +======= + +Please send us comments, experiences, questions, anything :) + +IRC: + #batman on irc.freenode.org +Mailing-list: + b.a.t.m.a.n@open-mesh.org (optional subscription at + https://lists.open-mesh.org/mailman3/postorius/lists/b.a.t.m.a.n.lists.open-mesh.org/) + +You can also contact the Authors: + +* Marek Lindner <mareklindner@neomailbox.ch> +* Simon Wunderlich <sw@simonwunderlich.de> |