diff options
author | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
---|---|---|
committer | Daniel Baumann <daniel.baumann@progress-linux.org> | 2024-04-27 10:05:51 +0000 |
commit | 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 (patch) | |
tree | a94efe259b9009378be6d90eb30d2b019d95c194 /Documentation/trace/coresight | |
parent | Initial commit. (diff) | |
download | linux-upstream/5.10.209.tar.xz linux-upstream/5.10.209.zip |
Adding upstream version 5.10.209.upstream/5.10.209upstream
Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
Diffstat (limited to 'Documentation/trace/coresight')
-rw-r--r-- | Documentation/trace/coresight/coresight-cpu-debug.rst | 192 | ||||
-rw-r--r-- | Documentation/trace/coresight/coresight-ect.rst | 226 | ||||
-rw-r--r-- | Documentation/trace/coresight/coresight-etm4x-reference.rst | 798 | ||||
-rw-r--r-- | Documentation/trace/coresight/coresight.rst | 596 | ||||
-rw-r--r-- | Documentation/trace/coresight/index.rst | 9 |
5 files changed, 1821 insertions, 0 deletions
diff --git a/Documentation/trace/coresight/coresight-cpu-debug.rst b/Documentation/trace/coresight/coresight-cpu-debug.rst new file mode 100644 index 000000000..993dd294b --- /dev/null +++ b/Documentation/trace/coresight/coresight-cpu-debug.rst @@ -0,0 +1,192 @@ +========================== +Coresight CPU Debug Module +========================== + + :Author: Leo Yan <leo.yan@linaro.org> + :Date: April 5th, 2017 + +Introduction +------------ + +Coresight CPU debug module is defined in ARMv8-a architecture reference manual +(ARM DDI 0487A.k) Chapter 'Part H: External debug', the CPU can integrate +debug module and it is mainly used for two modes: self-hosted debug and +external debug. Usually the external debug mode is well known as the external +debugger connects with SoC from JTAG port; on the other hand the program can +explore debugging method which rely on self-hosted debug mode, this document +is to focus on this part. + +The debug module provides sample-based profiling extension, which can be used +to sample CPU program counter, secure state and exception level, etc; usually +every CPU has one dedicated debug module to be connected. Based on self-hosted +debug mechanism, Linux kernel can access these related registers from mmio +region when the kernel panic happens. The callback notifier for kernel panic +will dump related registers for every CPU; finally this is good for assistant +analysis for panic. + + +Implementation +-------------- + +- During driver registration, it uses EDDEVID and EDDEVID1 - two device ID + registers to decide if sample-based profiling is implemented or not. On some + platforms this hardware feature is fully or partially implemented; and if + this feature is not supported then registration will fail. + +- At the time this documentation was written, the debug driver mainly relies on + information gathered by the kernel panic callback notifier from three + sampling registers: EDPCSR, EDVIDSR and EDCIDSR: from EDPCSR we can get + program counter; EDVIDSR has information for secure state, exception level, + bit width, etc; EDCIDSR is context ID value which contains the sampled value + of CONTEXTIDR_EL1. + +- The driver supports a CPU running in either AArch64 or AArch32 mode. The + registers naming convention is a bit different between them, AArch64 uses + 'ED' for register prefix (ARM DDI 0487A.k, chapter H9.1) and AArch32 uses + 'DBG' as prefix (ARM DDI 0487A.k, chapter G5.1). The driver is unified to + use AArch64 naming convention. + +- ARMv8-a (ARM DDI 0487A.k) and ARMv7-a (ARM DDI 0406C.b) have different + register bits definition. So the driver consolidates two difference: + + If PCSROffset=0b0000, on ARMv8-a the feature of EDPCSR is not implemented; + but ARMv7-a defines "PCSR samples are offset by a value that depends on the + instruction set state". For ARMv7-a, the driver checks furthermore if CPU + runs with ARM or thumb instruction set and calibrate PCSR value, the + detailed description for offset is in ARMv7-a ARM (ARM DDI 0406C.b) chapter + C11.11.34 "DBGPCSR, Program Counter Sampling Register". + + If PCSROffset=0b0010, ARMv8-a defines "EDPCSR implemented, and samples have + no offset applied and do not sample the instruction set state in AArch32 + state". So on ARMv8 if EDDEVID1.PCSROffset is 0b0010 and the CPU operates + in AArch32 state, EDPCSR is not sampled; when the CPU operates in AArch64 + state EDPCSR is sampled and no offset are applied. + + +Clock and power domain +---------------------- + +Before accessing debug registers, we should ensure the clock and power domain +have been enabled properly. In ARMv8-a ARM (ARM DDI 0487A.k) chapter 'H9.1 +Debug registers', the debug registers are spread into two domains: the debug +domain and the CPU domain. +:: + + +---------------+ + | | + | | + +----------+--+ | + dbg_clock -->| |**| |<-- cpu_clock + | Debug |**| CPU | + dbg_power_domain -->| |**| |<-- cpu_power_domain + +----------+--+ | + | | + | | + +---------------+ + +For debug domain, the user uses DT binding "clocks" and "power-domains" to +specify the corresponding clock source and power supply for the debug logic. +The driver calls the pm_runtime_{put|get} operations as needed to handle the +debug power domain. + +For CPU domain, the different SoC designs have different power management +schemes and finally this heavily impacts external debug module. So we can +divide into below cases: + +- On systems with a sane power controller which can behave correctly with + respect to CPU power domain, the CPU power domain can be controlled by + register EDPRCR in driver. The driver firstly writes bit EDPRCR.COREPURQ + to power up the CPU, and then writes bit EDPRCR.CORENPDRQ for emulation + of CPU power down. As result, this can ensure the CPU power domain is + powered on properly during the period when access debug related registers; + +- Some designs will power down an entire cluster if all CPUs on the cluster + are powered down - including the parts of the debug registers that should + remain powered in the debug power domain. The bits in EDPRCR are not + respected in these cases, so these designs do not support debug over + power down in the way that the CoreSight / Debug designers anticipated. + This means that even checking EDPRSR has the potential to cause a bus hang + if the target register is unpowered. + + In this case, accessing to the debug registers while they are not powered + is a recipe for disaster; so we need preventing CPU low power states at boot + time or when user enable module at the run time. Please see chapter + "How to use the module" for detailed usage info for this. + + +Device Tree Bindings +-------------------- + +See Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt for details. + + +How to use the module +--------------------- + +If you want to enable debugging functionality at boot time, you can add +"coresight_cpu_debug.enable=1" to the kernel command line parameter. + +The driver also can work as module, so can enable the debugging when insmod +module:: + + # insmod coresight_cpu_debug.ko debug=1 + +When boot time or insmod module you have not enabled the debugging, the driver +uses the debugfs file system to provide a knob to dynamically enable or disable +debugging: + +To enable it, write a '1' into /sys/kernel/debug/coresight_cpu_debug/enable:: + + # echo 1 > /sys/kernel/debug/coresight_cpu_debug/enable + +To disable it, write a '0' into /sys/kernel/debug/coresight_cpu_debug/enable:: + + # echo 0 > /sys/kernel/debug/coresight_cpu_debug/enable + +As explained in chapter "Clock and power domain", if you are working on one +platform which has idle states to power off debug logic and the power +controller cannot work well for the request from EDPRCR, then you should +firstly constraint CPU idle states before enable CPU debugging feature; so can +ensure the accessing to debug logic. + +If you want to limit idle states at boot time, you can use "nohlt" or +"cpuidle.off=1" in the kernel command line. + +At the runtime you can disable idle states with below methods: + +It is possible to disable CPU idle states by way of the PM QoS +subsystem, more specifically by using the "/dev/cpu_dma_latency" +interface (see Documentation/power/pm_qos_interface.rst for more +details). As specified in the PM QoS documentation the requested +parameter will stay in effect until the file descriptor is released. +For example:: + + # exec 3<> /dev/cpu_dma_latency; echo 0 >&3 + ... + Do some work... + ... + # exec 3<>- + +The same can also be done from an application program. + +Disable specific CPU's specific idle state from cpuidle sysfs (see +Documentation/admin-guide/pm/cpuidle.rst):: + + # echo 1 > /sys/devices/system/cpu/cpu$cpu/cpuidle/state$state/disable + +Output format +------------- + +Here is an example of the debugging output format:: + + ARM external debug module: + coresight-cpu-debug 850000.debug: CPU[0]: + coresight-cpu-debug 850000.debug: EDPRSR: 00000001 (Power:On DLK:Unlock) + coresight-cpu-debug 850000.debug: EDPCSR: handle_IPI+0x174/0x1d8 + coresight-cpu-debug 850000.debug: EDCIDSR: 00000000 + coresight-cpu-debug 850000.debug: EDVIDSR: 90000000 (State:Non-secure Mode:EL1/0 Width:64bits VMID:0) + coresight-cpu-debug 852000.debug: CPU[1]: + coresight-cpu-debug 852000.debug: EDPRSR: 00000001 (Power:On DLK:Unlock) + coresight-cpu-debug 852000.debug: EDPCSR: debug_notifier_call+0x23c/0x358 + coresight-cpu-debug 852000.debug: EDCIDSR: 00000000 + coresight-cpu-debug 852000.debug: EDVIDSR: 90000000 (State:Non-secure Mode:EL1/0 Width:64bits VMID:0) diff --git a/Documentation/trace/coresight/coresight-ect.rst b/Documentation/trace/coresight/coresight-ect.rst new file mode 100644 index 000000000..a68732c5c --- /dev/null +++ b/Documentation/trace/coresight/coresight-ect.rst @@ -0,0 +1,226 @@ +.. SPDX-License-Identifier: GPL-2.0 + +============================================= +CoreSight Embedded Cross Trigger (CTI & CTM). +============================================= + + :Author: Mike Leach <mike.leach@linaro.org> + :Date: November 2019 + +Hardware Description +-------------------- + +The CoreSight Cross Trigger Interface (CTI) is a hardware device that takes +individual input and output hardware signals known as triggers to and from +devices and interconnects them via the Cross Trigger Matrix (CTM) to other +devices via numbered channels, in order to propagate events between devices. + +e.g.:: + + 0000000 in_trigs ::::::: + 0 C 0----------->: : +======>(other CTI channel IO) + 0 P 0<-----------: : v + 0 U 0 out_trigs : : Channels ***** ::::::: + 0000000 : CTI :<=========>*CTM*<====>: CTI :---+ + ####### in_trigs : : (id 0-3) ***** ::::::: v + # ETM #----------->: : ^ ####### + # #<-----------: : +---# ETR # + ####### out_trigs ::::::: ####### + +The CTI driver enables the programming of the CTI to attach triggers to +channels. When an input trigger becomes active, the attached channel will +become active. Any output trigger attached to that channel will also +become active. The active channel is propagated to other CTIs via the CTM, +activating connected output triggers there, unless filtered by the CTI +channel gate. + +It is also possible to activate a channel using system software directly +programming registers in the CTI. + +The CTIs are registered by the system to be associated with CPUs and/or other +CoreSight devices on the trace data path. When these devices are enabled the +attached CTIs will also be enabled. By default/on power up the CTIs have +no programmed trigger/channel attachments, so will not affect the system +until explicitly programmed. + +The hardware trigger connections between CTIs and devices is implementation +defined, unless the CPU/ETM combination is a v8 architecture, in which case +the connections have an architecturally defined standard layout. + +The hardware trigger signals can also be connected to non-CoreSight devices +(e.g. UART), or be propagated off chip as hardware IO lines. + +All the CTI devices are associated with a CTM. On many systems there will be a +single effective CTM (one CTM, or multiple CTMs all interconnected), but it is +possible that systems can have nets of CTIs+CTM that are not interconnected by +a CTM to each other. On these systems a CTM index is declared to associate +CTI devices that are interconnected via a given CTM. + +Sysfs files and directories +--------------------------- + +The CTI devices appear on the existing CoreSight bus alongside the other +CoreSight devices:: + + >$ ls /sys/bus/coresight/devices + cti_cpu0 cti_cpu2 cti_sys0 etm0 etm2 funnel0 replicator0 tmc_etr0 + cti_cpu1 cti_cpu3 cti_sys1 etm1 etm3 funnel1 tmc_etf0 tpiu0 + +The ``cti_cpu<N>`` named CTIs are associated with a CPU, and any ETM used by +that core. The ``cti_sys<N>`` CTIs are general system infrastructure CTIs that +can be associated with other CoreSight devices, or other system hardware +capable of generating or using trigger signals.:: + + >$ ls /sys/bus/coresight/devices/etm0/cti_cpu0 + channels ctmid enable nr_trigger_cons mgmt power powered regs + connections subsystem triggers0 triggers1 uevent + +*Key file items are:-* + * ``enable``: enables/disables the CTI. Read to determine current state. + If this shows as enabled (1), but ``powered`` shows unpowered (0), then + the enable indicates a request to enabled when the device is powered. + * ``ctmid`` : associated CTM - only relevant if system has multiple CTI+CTM + clusters that are not interconnected. + * ``nr_trigger_cons`` : total connections - triggers<N> directories. + * ``powered`` : Read to determine if the CTI is currently powered. + +*Sub-directories:-* + * ``triggers<N>``: contains list of triggers for an individual connection. + * ``channels``: Contains the channel API - CTI main programming interface. + * ``regs``: Gives access to the raw programmable CTI regs. + * ``mgmt``: the standard CoreSight management registers. + * ``connections``: Links to connected *CoreSight* devices. The number of + links can be 0 to ``nr_trigger_cons``. Actual number given by ``nr_links`` + in this directory. + + +triggers<N> directories +~~~~~~~~~~~~~~~~~~~~~~~ + +Individual trigger connection information. This describes trigger signals for +CoreSight and non-CoreSight connections. + +Each triggers directory has a set of parameters describing the triggers for +the connection. + + * ``name`` : name of connection + * ``in_signals`` : input trigger signal indexes used in this connection. + * ``in_types`` : functional types for in signals. + * ``out_signals`` : output trigger signals for this connection. + * ``out_types`` : functional types for out signals. + +e.g:: + + >$ ls ./cti_cpu0/triggers0/ + in_signals in_types name out_signals out_types + >$ cat ./cti_cpu0/triggers0/name + cpu0 + >$ cat ./cti_cpu0/triggers0/out_signals + 0-2 + >$ cat ./cti_cpu0/triggers0/out_types + pe_edbgreq pe_dbgrestart pe_ctiirq + >$ cat ./cti_cpu0/triggers0/in_signals + 0-1 + >$ cat ./cti_cpu0/triggers0/in_types + pe_dbgtrigger pe_pmuirq + +If a connection has zero signals in either the 'in' or 'out' triggers then +those parameters will be omitted. + +Channels API Directory +~~~~~~~~~~~~~~~~~~~~~~ + +This provides an easy way to attach triggers to channels, without needing +the multiple register operations that are required if manipulating the +'regs' sub-directory elements directly. + +A number of files provide this API:: + + >$ ls ./cti_sys0/channels/ + chan_clear chan_inuse chan_xtrigs_out trigin_attach + chan_free chan_pulse chan_xtrigs_reset trigin_detach + chan_gate_disable chan_set chan_xtrigs_sel trigout_attach + chan_gate_enable chan_xtrigs_in trig_filter_enable trigout_detach + trigout_filtered + +Most access to these elements take the form:: + + echo <chan> [<trigger>] > /<device_path>/<operation> + +where the optional <trigger> is only needed for trigXX_attach | detach +operations. + +e.g.:: + + >$ echo 0 1 > ./cti_sys0/channels/trigout_attach + >$ echo 0 > ./cti_sys0/channels/chan_set + +Attaches trigout(1) to channel(0), then activates channel(0) generating a +set state on cti_sys0.trigout(1) + + +*API operations* + + * ``trigin_attach, trigout_attach``: Attach a channel to a trigger signal. + * ``trigin_detach, trigout_detach``: Detach a channel from a trigger signal. + * ``chan_set``: Set the channel - the set state will be propagated around + the CTM to other connected devices. + * ``chan_clear``: Clear the channel. + * ``chan_pulse``: Set the channel for a single CoreSight clock cycle. + * ``chan_gate_enable``: Write operation sets the CTI gate to propagate + (enable) the channel to other devices. This operation takes a channel + number. CTI gate is enabled for all channels by default at power up. Read + to list the currently enabled channels on the gate. + * ``chan_gate_disable``: Write channel number to disable gate for that + channel. + * ``chan_inuse``: Show the current channels attached to any signal + * ``chan_free``: Show channels with no attached signals. + * ``chan_xtrigs_sel``: write a channel number to select a channel to view, + read to show the selected channel number. + * ``chan_xtrigs_in``: Read to show the input triggers attached to + the selected view channel. + * ``chan_xtrigs_out``:Read to show the output triggers attached to + the selected view channel. + * ``trig_filter_enable``: Defaults to enabled, disable to allow potentially + dangerous output signals to be set. + * ``trigout_filtered``: Trigger out signals that are prevented from being + set if filtering ``trig_filter_enable`` is enabled. One use is to prevent + accidental ``EDBGREQ`` signals stopping a core. + * ``chan_xtrigs_reset``: Write 1 to clear all channel / trigger programming. + Resets device hardware to default state. + + +The example below attaches input trigger index 1 to channel 2, and output +trigger index 6 to the same channel. It then examines the state of the +channel / trigger connections using the appropriate sysfs attributes. + +The settings mean that if either input trigger 1, or channel 2 go active then +trigger out 6 will go active. We then enable the CTI, and use the software +channel control to activate channel 2. We see the active channel on the +``choutstatus`` register and the active signal on the ``trigoutstatus`` +register. Finally clearing the channel removes this. + +e.g.:: + + .../cti_sys0/channels# echo 2 1 > trigin_attach + .../cti_sys0/channels# echo 2 6 > trigout_attach + .../cti_sys0/channels# cat chan_free + 0-1,3 + .../cti_sys0/channels# cat chan_inuse + 2 + .../cti_sys0/channels# echo 2 > chan_xtrigs_sel + .../cti_sys0/channels# cat chan_xtrigs_trigin + 1 + .../cti_sys0/channels# cat chan_xtrigs_trigout + 6 + .../cti_sys0/# echo 1 > enable + .../cti_sys0/channels# echo 2 > chan_set + .../cti_sys0/channels# cat ../regs/choutstatus + 0x4 + .../cti_sys0/channels# cat ../regs/trigoutstatus + 0x40 + .../cti_sys0/channels# echo 2 > chan_clear + .../cti_sys0/channels# cat ../regs/trigoutstatus + 0x0 + .../cti_sys0/channels# cat ../regs/choutstatus + 0x0 diff --git a/Documentation/trace/coresight/coresight-etm4x-reference.rst b/Documentation/trace/coresight/coresight-etm4x-reference.rst new file mode 100644 index 000000000..b64d9a9c7 --- /dev/null +++ b/Documentation/trace/coresight/coresight-etm4x-reference.rst @@ -0,0 +1,798 @@ +=============================================== +ETMv4 sysfs linux driver programming reference. +=============================================== + + :Author: Mike Leach <mike.leach@linaro.org> + :Date: October 11th, 2019 + +Supplement to existing ETMv4 driver documentation. + +Sysfs files and directories +--------------------------- + +Root: ``/sys/bus/coresight/devices/etm<N>`` + + +The following paragraphs explain the association between sysfs files and the +ETMv4 registers that they effect. Note the register names are given without +the ‘TRC’ prefix. + +---- + +:File: ``mode`` (rw) +:Trace Registers: {CONFIGR + others} +:Notes: + Bit select trace features. See ‘mode’ section below. Bits + in this will cause equivalent programming of trace config and + other registers to enable the features requested. + +:Syntax & eg: + ``echo bitfield > mode`` + + bitfield up to 32 bits setting trace features. + +:Example: + ``$> echo 0x012 > mode`` + +---- + +:File: ``reset`` (wo) +:Trace Registers: All +:Notes: + Reset all programming to trace nothing / no logic programmed. + +:Syntax: + ``echo 1 > reset`` + +---- + +:File: ``enable_source`` (wo) +:Trace Registers: PRGCTLR, All hardware regs. +:Notes: + - > 0 : Programs up the hardware with the current values held in the driver + and enables trace. + + - = 0 : disable trace hardware. + +:Syntax: + ``echo 1 > enable_source`` + +---- + +:File: ``cpu`` (ro) +:Trace Registers: None. +:Notes: + CPU ID that this ETM is attached to. + +:Example: + ``$> cat cpu`` + + ``$> 0`` + +---- + +:File: ``addr_idx`` (rw) +:Trace Registers: None. +:Notes: + Virtual register to index address comparator and range + features. Set index for first of the pair in a range. + +:Syntax: + ``echo idx > addr_idx`` + + Where idx < nr_addr_cmp x 2 + +---- + +:File: ``addr_range`` (rw) +:Trace Registers: ACVR[idx, idx+1], VIIECTLR +:Notes: + Pair of addresses for a range selected by addr_idx. Include + / exclude according to the optional parameter, or if omitted + uses the current ‘mode’ setting. Select comparator range in + control register. Error if index is odd value. + +:Depends: ``mode, addr_idx`` +:Syntax: + ``echo addr1 addr2 [exclude] > addr_range`` + + Where addr1 and addr2 define the range and addr1 < addr2. + + Optional exclude value:- + + - 0 for include + - 1 for exclude. +:Example: + ``$> echo 0x0000 0x2000 0 > addr_range`` + +---- + +:File: ``addr_single`` (rw) +:Trace Registers: ACVR[idx] +:Notes: + Set a single address comparator according to addr_idx. This + is used if the address comparator is used as part of event + generation logic etc. + +:Depends: ``addr_idx`` +:Syntax: + ``echo addr1 > addr_single`` + +---- + +:File: ``addr_start`` (rw) +:Trace Registers: ACVR[idx], VISSCTLR +:Notes: + Set a trace start address comparator according to addr_idx. + Select comparator in control register. + +:Depends: ``addr_idx`` +:Syntax: + ``echo addr1 > addr_start`` + +---- + +:File: ``addr_stop`` (rw) +:Trace Registers: ACVR[idx], VISSCTLR +:Notes: + Set a trace stop address comparator according to addr_idx. + Select comparator in control register. + +:Depends: ``addr_idx`` +:Syntax: + ``echo addr1 > addr_stop`` + +---- + +:File: ``addr_context`` (rw) +:Trace Registers: ACATR[idx,{6:4}] +:Notes: + Link context ID comparator to address comparator addr_idx + +:Depends: ``addr_idx`` +:Syntax: + ``echo ctxt_idx > addr_context`` + + Where ctxt_idx is the index of the linked context id / vmid + comparator. + +---- + +:File: ``addr_ctxtype`` (rw) +:Trace Registers: ACATR[idx,{3:2}] +:Notes: + Input value string. Set type for linked context ID comparator + +:Depends: ``addr_idx`` +:Syntax: + ``echo type > addr_ctxtype`` + + Type one of {all, vmid, ctxid, none} +:Example: + ``$> echo ctxid > addr_ctxtype`` + +---- + +:File: ``addr_exlevel_s_ns`` (rw) +:Trace Registers: ACATR[idx,{14:8}] +:Notes: + Set the ELx secure and non-secure matching bits for the + selected address comparator + +:Depends: ``addr_idx`` +:Syntax: + ``echo val > addr_exlevel_s_ns`` + + val is a 7 bit value for exception levels to exclude. Input + value shifted to correct bits in register. +:Example: + ``$> echo 0x4F > addr_exlevel_s_ns`` + +---- + +:File: ``addr_instdatatype`` (rw) +:Trace Registers: ACATR[idx,{1:0}] +:Notes: + Set the comparator address type for matching. Driver only + supports setting instruction address type. + +:Depends: ``addr_idx`` + +---- + +:File: ``addr_cmp_view`` (ro) +:Trace Registers: ACVR[idx, idx+1], ACATR[idx], VIIECTLR +:Notes: + Read the currently selected address comparator. If part of + address range then display both addresses. + +:Depends: ``addr_idx`` +:Syntax: + ``cat addr_cmp_view`` +:Example: + ``$> cat addr_cmp_view`` + + ``addr_cmp[0] range 0x0 0xffffffffffffffff include ctrl(0x4b00)`` + +---- + +:File: ``nr_addr_cmp`` (ro) +:Trace Registers: From IDR4 +:Notes: + Number of address comparator pairs + +---- + +:File: ``sshot_idx`` (rw) +:Trace Registers: None +:Notes: + Select single shot register set. + +---- + +:File: ``sshot_ctrl`` (rw) +:Trace Registers: SSCCR[idx] +:Notes: + Access a single shot comparator control register. + +:Depends: ``sshot_idx`` +:Syntax: + ``echo val > sshot_ctrl`` + + Writes val into the selected control register. + +---- + +:File: ``sshot_status`` (ro) +:Trace Registers: SSCSR[idx] +:Notes: + Read a single shot comparator status register + +:Depends: ``sshot_idx`` +:Syntax: + ``cat sshot_status`` + + Read status. +:Example: + ``$> cat sshot_status`` + + ``0x1`` + +---- + +:File: ``sshot_pe_ctrl`` (rw) +:Trace Registers: SSPCICR[idx] +:Notes: + Access a single shot PE comparator input control register. + +:Depends: ``sshot_idx`` +:Syntax: + ``echo val > sshot_pe_ctrl`` + + Writes val into the selected control register. + +---- + +:File: ``ns_exlevel_vinst`` (rw) +:Trace Registers: VICTLR{23:20} +:Notes: + Program non-secure exception level filters. Set / clear NS + exception filter bits. Setting ‘1’ excludes trace from the + exception level. + +:Syntax: + ``echo bitfield > ns_exlevel_viinst`` + + Where bitfield contains bits to set clear for EL0 to EL2 +:Example: + ``%> echo 0x4 > ns_exlevel_viinst`` + + Excludes EL2 NS trace. + +---- + +:File: ``vinst_pe_cmp_start_stop`` (rw) +:Trace Registers: VIPCSSCTLR +:Notes: + Access PE start stop comparator input control registers + +---- + +:File: ``bb_ctrl`` (rw) +:Trace Registers: BBCTLR +:Notes: + Define ranges that Branch Broadcast will operate in. + Default (0x0) is all addresses. + +:Depends: BB enabled. + +---- + +:File: ``cyc_threshold`` (rw) +:Trace Registers: CCCTLR +:Notes: + Set the threshold for which cycle counts will be emitted. + Error if attempt to set below minimum defined in IDR3, masked + to width of valid bits. + +:Depends: CC enabled. + +---- + +:File: ``syncfreq`` (rw) +:Trace Registers: SYNCPR +:Notes: + Set trace synchronisation period. Power of 2 value, 0 (off) + or 8-20. Driver defaults to 12 (every 4096 bytes). + +---- + +:File: ``cntr_idx`` (rw) +:Trace Registers: none +:Notes: + Select the counter to access + +:Syntax: + ``echo idx > cntr_idx`` + + Where idx < nr_cntr + +---- + +:File: ``cntr_ctrl`` (rw) +:Trace Registers: CNTCTLR[idx] +:Notes: + Set counter control value. + +:Depends: ``cntr_idx`` +:Syntax: + ``echo val > cntr_ctrl`` + + Where val is per ETMv4 spec. + +---- + +:File: ``cntrldvr`` (rw) +:Trace Registers: CNTRLDVR[idx] +:Notes: + Set counter reload value. + +:Depends: ``cntr_idx`` +:Syntax: + ``echo val > cntrldvr`` + + Where val is per ETMv4 spec. + +---- + +:File: ``nr_cntr`` (ro) +:Trace Registers: From IDR5 + +:Notes: + Number of counters implemented. + +---- + +:File: ``ctxid_idx`` (rw) +:Trace Registers: None +:Notes: + Select the context ID comparator to access + +:Syntax: + ``echo idx > ctxid_idx`` + + Where idx < numcidc + +---- + +:File: ``ctxid_pid`` (rw) +:Trace Registers: CIDCVR[idx] +:Notes: + Set the context ID comparator value + +:Depends: ``ctxid_idx`` + +---- + +:File: ``ctxid_masks`` (rw) +:Trace Registers: CIDCCTLR0, CIDCCTLR1, CIDCVR<0-7> +:Notes: + Pair of values to set the byte masks for 1-8 context ID + comparators. Automatically clears masked bytes to 0 in CID + value registers. + +:Syntax: + ``echo m3m2m1m0 [m7m6m5m4] > ctxid_masks`` + + 32 bit values made up of mask bytes, where mN represents a + byte mask value for Context ID comparator N. + + Second value not required on systems that have fewer than 4 + context ID comparators + +---- + +:File: ``numcidc`` (ro) +:Trace Registers: From IDR4 +:Notes: + Number of Context ID comparators + +---- + +:File: ``vmid_idx`` (rw) +:Trace Registers: None +:Notes: + Select the VM ID comparator to access. + +:Syntax: + ``echo idx > vmid_idx`` + + Where idx < numvmidc + +---- + +:File: ``vmid_val`` (rw) +:Trace Registers: VMIDCVR[idx] +:Notes: + Set the VM ID comparator value + +:Depends: ``vmid_idx`` + +---- + +:File: ``vmid_masks`` (rw) +:Trace Registers: VMIDCCTLR0, VMIDCCTLR1, VMIDCVR<0-7> +:Notes: + Pair of values to set the byte masks for 1-8 VM ID comparators. + Automatically clears masked bytes to 0 in VMID value registers. + +:Syntax: + ``echo m3m2m1m0 [m7m6m5m4] > vmid_masks`` + + Where mN represents a byte mask value for VMID comparator N. + Second value not required on systems that have fewer than 4 + VMID comparators. + +---- + +:File: ``numvmidc`` (ro) +:Trace Registers: From IDR4 +:Notes: + Number of VMID comparators + +---- + +:File: ``res_idx`` (rw) +:Trace Registers: None. +:Notes: + Select the resource selector control to access. Must be 2 or + higher as selectors 0 and 1 are hardwired. + +:Syntax: + ``echo idx > res_idx`` + + Where 2 <= idx < nr_resource x 2 + +---- + +:File: ``res_ctrl`` (rw) +:Trace Registers: RSCTLR[idx] +:Notes: + Set resource selector control value. Value per ETMv4 spec. + +:Depends: ``res_idx`` +:Syntax: + ``echo val > res_cntr`` + + Where val is per ETMv4 spec. + +---- + +:File: ``nr_resource`` (ro) +:Trace Registers: From IDR4 +:Notes: + Number of resource selector pairs + +---- + +:File: ``event`` (rw) +:Trace Registers: EVENTCTRL0R +:Notes: + Set up to 4 implemented event fields. + +:Syntax: + ``echo ev3ev2ev1ev0 > event`` + + Where evN is an 8 bit event field. Up to 4 event fields make up the + 32-bit input value. Number of valid fields is implementation dependent, + defined in IDR0. + +---- + +:File: ``event_instren`` (rw) +:Trace Registers: EVENTCTRL1R +:Notes: + Choose events which insert event packets into trace stream. + +:Depends: EVENTCTRL0R +:Syntax: + ``echo bitfield > event_instren`` + + Where bitfield is up to 4 bits according to number of event fields. + +---- + +:File: ``event_ts`` (rw) +:Trace Registers: TSCTLR +:Notes: + Set the event that will generate timestamp requests. + +:Depends: ``TS activated`` +:Syntax: + ``echo evfield > event_ts`` + + Where evfield is an 8 bit event selector. + +---- + +:File: ``seq_idx`` (rw) +:Trace Registers: None +:Notes: + Sequencer event register select - 0 to 2 + +---- + +:File: ``seq_state`` (rw) +:Trace Registers: SEQSTR +:Notes: + Sequencer current state - 0 to 3. + +---- + +:File: ``seq_event`` (rw) +:Trace Registers: SEQEVR[idx] +:Notes: + State transition event registers + +:Depends: ``seq_idx`` +:Syntax: + ``echo evBevF > seq_event`` + + Where evBevF is a 16 bit value made up of two event selectors, + + - evB : back + - evF : forwards. + +---- + +:File: ``seq_reset_event`` (rw) +:Trace Registers: SEQRSTEVR +:Notes: + Sequencer reset event + +:Syntax: + ``echo evfield > seq_reset_event`` + + Where evfield is an 8 bit event selector. + +---- + +:File: ``nrseqstate`` (ro) +:Trace Registers: From IDR5 +:Notes: + Number of sequencer states (0 or 4) + +---- + +:File: ``nr_pe_cmp`` (ro) +:Trace Registers: From IDR4 +:Notes: + Number of PE comparator inputs + +---- + +:File: ``nr_ext_inp`` (ro) +:Trace Registers: From IDR5 +:Notes: + Number of external inputs + +---- + +:File: ``nr_ss_cmp`` (ro) +:Trace Registers: From IDR4 +:Notes: + Number of Single Shot control registers + +---- + +*Note:* When programming any address comparator the driver will tag the +comparator with a type used - i.e. RANGE, SINGLE, START, STOP. Once this tag +is set, then only the values can be changed using the same sysfs file / type +used to program it. + +Thus:: + + % echo 0 > addr_idx ; select address comparator 0 + % echo 0x1000 0x5000 0 > addr_range ; set address range on comparators 0, 1. + % echo 0x2000 > addr_start ; error as comparator 0 is a range comparator + % echo 2 > addr_idx ; select address comparator 2 + % echo 0x2000 > addr_start ; this is OK as comparator 2 is unused. + % echo 0x3000 > addr_stop ; error as comparator 2 set as start address. + % echo 2 > addr_idx ; select address comparator 3 + % echo 0x3000 > addr_stop ; this is OK + +To remove programming on all the comparators (and all the other hardware) use +the reset parameter:: + + % echo 1 > reset + + + +The ‘mode’ sysfs parameter. +--------------------------- + +This is a bitfield selection parameter that sets the overall trace mode for the +ETM. The table below describes the bits, using the defines from the driver +source file, along with a description of the feature these represent. Many +features are optional and therefore dependent on implementation in the +hardware. + +Bit assignments shown below:- + +---- + +**bit (0):** + ETM_MODE_EXCLUDE + +**description:** + This is the default value for the include / exclude function when + setting address ranges. Set 1 for exclude range. When the mode + parameter is set this value is applied to the currently indexed + address range. + + +**bit (4):** + ETM_MODE_BB + +**description:** + Set to enable branch broadcast if supported in hardware [IDR0]. + + +**bit (5):** + ETMv4_MODE_CYCACC + +**description:** + Set to enable cycle accurate trace if supported [IDR0]. + + +**bit (6):** + ETMv4_MODE_CTXID + +**description:** + Set to enable context ID tracing if supported in hardware [IDR2]. + + +**bit (7):** + ETM_MODE_VMID + +**description:** + Set to enable virtual machine ID tracing if supported [IDR2]. + + +**bit (11):** + ETMv4_MODE_TIMESTAMP + +**description:** + Set to enable timestamp generation if supported [IDR0]. + + +**bit (12):** + ETM_MODE_RETURNSTACK +**description:** + Set to enable trace return stack use if supported [IDR0]. + + +**bit (13-14):** + ETM_MODE_QELEM(val) + +**description:** + ‘val’ determines level of Q element support enabled if + implemented by the ETM [IDR0] + + +**bit (19):** + ETM_MODE_ATB_TRIGGER + +**description:** + Set to enable the ATBTRIGGER bit in the event control register + [EVENTCTLR1] if supported [IDR5]. + + +**bit (20):** + ETM_MODE_LPOVERRIDE + +**description:** + Set to enable the LPOVERRIDE bit in the event control register + [EVENTCTLR1], if supported [IDR5]. + + +**bit (21):** + ETM_MODE_ISTALL_EN + +**description:** + Set to enable the ISTALL bit in the stall control register + [STALLCTLR] + + +**bit (23):** + ETM_MODE_INSTPRIO + +**description:** + Set to enable the INSTPRIORITY bit in the stall control register + [STALLCTLR] , if supported [IDR0]. + + +**bit (24):** + ETM_MODE_NOOVERFLOW + +**description:** + Set to enable the NOOVERFLOW bit in the stall control register + [STALLCTLR], if supported [IDR3]. + + +**bit (25):** + ETM_MODE_TRACE_RESET + +**description:** + Set to enable the TRCRESET bit in the viewinst control register + [VICTLR] , if supported [IDR3]. + + +**bit (26):** + ETM_MODE_TRACE_ERR + +**description:** + Set to enable the TRCCTRL bit in the viewinst control register + [VICTLR]. + + +**bit (27):** + ETM_MODE_VIEWINST_STARTSTOP + +**description:** + Set the initial state value of the ViewInst start / stop logic + in the viewinst control register [VICTLR] + + +**bit (30):** + ETM_MODE_EXCL_KERN + +**description:** + Set default trace setup to exclude kernel mode trace (see note a) + + +**bit (31):** + ETM_MODE_EXCL_USER + +**description:** + Set default trace setup to exclude user space trace (see note a) + +---- + +*Note a)* On startup the ETM is programmed to trace the complete address space +using address range comparator 0. ‘mode’ bits 30 / 31 modify this setting to +set EL exclude bits for NS state in either user space (EL0) or kernel space +(EL1) in the address range comparator. (the default setting excludes all +secure EL, and NS EL2) + +Once the reset parameter has been used, and/or custom programming has been +implemented - using these bits will result in the EL bits for address +comparator 0 being set in the same way. + +*Note b)* Bits 2-3, 8-10, 15-16, 18, 22, control features that only work with +data trace. As A-profile data trace is architecturally prohibited in ETMv4, +these have been omitted here. Possible uses could be where a kernel has +support for control of R or M profile infrastructure as part of a heterogeneous +system. + +Bits 17, 28-29 are unused. diff --git a/Documentation/trace/coresight/coresight.rst b/Documentation/trace/coresight/coresight.rst new file mode 100644 index 000000000..0b73acb44 --- /dev/null +++ b/Documentation/trace/coresight/coresight.rst @@ -0,0 +1,596 @@ +====================================== +Coresight - HW Assisted Tracing on ARM +====================================== + + :Author: Mathieu Poirier <mathieu.poirier@linaro.org> + :Date: September 11th, 2014 + +Introduction +------------ + +Coresight is an umbrella of technologies allowing for the debugging of ARM +based SoC. It includes solutions for JTAG and HW assisted tracing. This +document is concerned with the latter. + +HW assisted tracing is becoming increasingly useful when dealing with systems +that have many SoCs and other components like GPU and DMA engines. ARM has +developed a HW assisted tracing solution by means of different components, each +being added to a design at synthesis time to cater to specific tracing needs. +Components are generally categorised as source, link and sinks and are +(usually) discovered using the AMBA bus. + +"Sources" generate a compressed stream representing the processor instruction +path based on tracing scenarios as configured by users. From there the stream +flows through the coresight system (via ATB bus) using links that are connecting +the emanating source to a sink(s). Sinks serve as endpoints to the coresight +implementation, either storing the compressed stream in a memory buffer or +creating an interface to the outside world where data can be transferred to a +host without fear of filling up the onboard coresight memory buffer. + +At typical coresight system would look like this:: + + ***************************************************************** + **************************** AMBA AXI ****************************===|| + ***************************************************************** || + ^ ^ | || + | | * ** + 0000000 ::::: 0000000 ::::: ::::: @@@@@@@ |||||||||||| + 0 CPU 0<-->: C : 0 CPU 0<-->: C : : C : @ STM @ || System || + |->0000000 : T : |->0000000 : T : : T :<--->@@@@@ || Memory || + | #######<-->: I : | #######<-->: I : : I : @@@<-| |||||||||||| + | # ETM # ::::: | # PTM # ::::: ::::: @ | + | ##### ^ ^ | ##### ^ ! ^ ! . | ||||||||| + | |->### | ! | |->### | ! | ! . | || DAP || + | | # | ! | | # | ! | ! . | ||||||||| + | | . | ! | | . | ! | ! . | | | + | | . | ! | | . | ! | ! . | | * + | | . | ! | | . | ! | ! . | | SWD/ + | | . | ! | | . | ! | ! . | | JTAG + *****************************************************************<-| + *************************** AMBA Debug APB ************************ + ***************************************************************** + | . ! . ! ! . | + | . * . * * . | + ***************************************************************** + ******************** Cross Trigger Matrix (CTM) ******************* + ***************************************************************** + | . ^ . . | + | * ! * * | + ***************************************************************** + ****************** AMBA Advanced Trace Bus (ATB) ****************** + ***************************************************************** + | ! =============== | + | * ===== F =====<---------| + | ::::::::: ==== U ==== + |-->:: CTI ::<!! === N === + | ::::::::: ! == N == + | ^ * == E == + | ! &&&&&&&&& IIIIIII == L == + |------>&& ETB &&<......II I ======= + | ! &&&&&&&&& II I . + | ! I I . + | ! I REP I<.......... + | ! I I + | !!>&&&&&&&&& II I *Source: ARM ltd. + |------>& TPIU &<......II I DAP = Debug Access Port + &&&&&&&&& IIIIIII ETM = Embedded Trace Macrocell + ; PTM = Program Trace Macrocell + ; CTI = Cross Trigger Interface + * ETB = Embedded Trace Buffer + To trace port TPIU= Trace Port Interface Unit + SWD = Serial Wire Debug + +While on target configuration of the components is done via the APB bus, +all trace data are carried out-of-band on the ATB bus. The CTM provides +a way to aggregate and distribute signals between CoreSight components. + +The coresight framework provides a central point to represent, configure and +manage coresight devices on a platform. This first implementation centers on +the basic tracing functionality, enabling components such ETM/PTM, funnel, +replicator, TMC, TPIU and ETB. Future work will enable more +intricate IP blocks such as STM and CTI. + + +Acronyms and Classification +--------------------------- + +Acronyms: + +PTM: + Program Trace Macrocell +ETM: + Embedded Trace Macrocell +STM: + System trace Macrocell +ETB: + Embedded Trace Buffer +ITM: + Instrumentation Trace Macrocell +TPIU: + Trace Port Interface Unit +TMC-ETR: + Trace Memory Controller, configured as Embedded Trace Router +TMC-ETF: + Trace Memory Controller, configured as Embedded Trace FIFO +CTI: + Cross Trigger Interface + +Classification: + +Source: + ETMv3.x ETMv4, PTMv1.0, PTMv1.1, STM, STM500, ITM +Link: + Funnel, replicator (intelligent or not), TMC-ETR +Sinks: + ETBv1.0, ETB1.1, TPIU, TMC-ETF +Misc: + CTI + + +Device Tree Bindings +-------------------- + +See Documentation/devicetree/bindings/arm/coresight.txt for details. + +As of this writing drivers for ITM, STMs and CTIs are not provided but are +expected to be added as the solution matures. + + +Framework and implementation +---------------------------- + +The coresight framework provides a central point to represent, configure and +manage coresight devices on a platform. Any coresight compliant device can +register with the framework for as long as they use the right APIs: + +.. c:function:: struct coresight_device *coresight_register(struct coresight_desc *desc); +.. c:function:: void coresight_unregister(struct coresight_device *csdev); + +The registering function is taking a ``struct coresight_desc *desc`` and +register the device with the core framework. The unregister function takes +a reference to a ``struct coresight_device *csdev`` obtained at registration time. + +If everything goes well during the registration process the new devices will +show up under /sys/bus/coresight/devices, as showns here for a TC2 platform:: + + root:~# ls /sys/bus/coresight/devices/ + replicator 20030000.tpiu 2201c000.ptm 2203c000.etm 2203e000.etm + 20010000.etb 20040000.funnel 2201d000.ptm 2203d000.etm + root:~# + +The functions take a ``struct coresight_device``, which looks like this:: + + struct coresight_desc { + enum coresight_dev_type type; + struct coresight_dev_subtype subtype; + const struct coresight_ops *ops; + struct coresight_platform_data *pdata; + struct device *dev; + const struct attribute_group **groups; + }; + + +The "coresight_dev_type" identifies what the device is, i.e, source link or +sink while the "coresight_dev_subtype" will characterise that type further. + +The ``struct coresight_ops`` is mandatory and will tell the framework how to +perform base operations related to the components, each component having +a different set of requirement. For that ``struct coresight_ops_sink``, +``struct coresight_ops_link`` and ``struct coresight_ops_source`` have been +provided. + +The next field ``struct coresight_platform_data *pdata`` is acquired by calling +``of_get_coresight_platform_data()``, as part of the driver's _probe routine and +``struct device *dev`` gets the device reference embedded in the ``amba_device``:: + + static int etm_probe(struct amba_device *adev, const struct amba_id *id) + { + ... + ... + drvdata->dev = &adev->dev; + ... + } + +Specific class of device (source, link, or sink) have generic operations +that can be performed on them (see ``struct coresight_ops``). The ``**groups`` +is a list of sysfs entries pertaining to operations +specific to that component only. "Implementation defined" customisations are +expected to be accessed and controlled using those entries. + +Device Naming scheme +-------------------- + +The devices that appear on the "coresight" bus were named the same as their +parent devices, i.e, the real devices that appears on AMBA bus or the platform bus. +Thus the names were based on the Linux Open Firmware layer naming convention, +which follows the base physical address of the device followed by the device +type. e.g:: + + root:~# ls /sys/bus/coresight/devices/ + 20010000.etf 20040000.funnel 20100000.stm 22040000.etm + 22140000.etm 230c0000.funnel 23240000.etm 20030000.tpiu + 20070000.etr 20120000.replicator 220c0000.funnel + 23040000.etm 23140000.etm 23340000.etm + +However, with the introduction of ACPI support, the names of the real +devices are a bit cryptic and non-obvious. Thus, a new naming scheme was +introduced to use more generic names based on the type of the device. The +following rules apply:: + + 1) Devices that are bound to CPUs, are named based on the CPU logical + number. + + e.g, ETM bound to CPU0 is named "etm0" + + 2) All other devices follow a pattern, "<device_type_prefix>N", where : + + <device_type_prefix> - A prefix specific to the type of the device + N - a sequential number assigned based on the order + of probing. + + e.g, tmc_etf0, tmc_etr0, funnel0, funnel1 + +Thus, with the new scheme the devices could appear as :: + + root:~# ls /sys/bus/coresight/devices/ + etm0 etm1 etm2 etm3 etm4 etm5 funnel0 + funnel1 funnel2 replicator0 stm0 tmc_etf0 tmc_etr0 tpiu0 + +Some of the examples below might refer to old naming scheme and some +to the newer scheme, to give a confirmation that what you see on your +system is not unexpected. One must use the "names" as they appear on +the system under specified locations. + +Topology Representation +----------------------- + +Each CoreSight component has a ``connections`` directory which will contain +links to other CoreSight components. This allows the user to explore the trace +topology and for larger systems, determine the most appropriate sink for a +given source. The connection information can also be used to establish +which CTI devices are connected to a given component. This directory contains a +``nr_links`` attribute detailing the number of links in the directory. + +For an ETM source, in this case ``etm0`` on a Juno platform, a typical +arrangement will be:: + + linaro-developer:~# ls - l /sys/bus/coresight/devices/etm0/connections + <file details> cti_cpu0 -> ../../../23020000.cti/cti_cpu0 + <file details> nr_links + <file details> out:0 -> ../../../230c0000.funnel/funnel2 + +Following the out port to ``funnel2``:: + + linaro-developer:~# ls -l /sys/bus/coresight/devices/funnel2/connections + <file details> in:0 -> ../../../23040000.etm/etm0 + <file details> in:1 -> ../../../23140000.etm/etm3 + <file details> in:2 -> ../../../23240000.etm/etm4 + <file details> in:3 -> ../../../23340000.etm/etm5 + <file details> nr_links + <file details> out:0 -> ../../../20040000.funnel/funnel0 + +And again to ``funnel0``:: + + linaro-developer:~# ls -l /sys/bus/coresight/devices/funnel0/connections + <file details> in:0 -> ../../../220c0000.funnel/funnel1 + <file details> in:1 -> ../../../230c0000.funnel/funnel2 + <file details> nr_links + <file details> out:0 -> ../../../20010000.etf/tmc_etf0 + +Finding the first sink ``tmc_etf0``. This can be used to collect data +as a sink, or as a link to propagate further along the chain:: + + linaro-developer:~# ls -l /sys/bus/coresight/devices/tmc_etf0/connections + <file details> cti_sys0 -> ../../../20020000.cti/cti_sys0 + <file details> in:0 -> ../../../20040000.funnel/funnel0 + <file details> nr_links + <file details> out:0 -> ../../../20150000.funnel/funnel4 + +via ``funnel4``:: + + linaro-developer:~# ls -l /sys/bus/coresight/devices/funnel4/connections + <file details> in:0 -> ../../../20010000.etf/tmc_etf0 + <file details> in:1 -> ../../../20140000.etf/tmc_etf1 + <file details> nr_links + <file details> out:0 -> ../../../20120000.replicator/replicator0 + +and a ``replicator0``:: + + linaro-developer:~# ls -l /sys/bus/coresight/devices/replicator0/connections + <file details> in:0 -> ../../../20150000.funnel/funnel4 + <file details> nr_links + <file details> out:0 -> ../../../20030000.tpiu/tpiu0 + <file details> out:1 -> ../../../20070000.etr/tmc_etr0 + +Arriving at the final sink in the chain, ``tmc_etr0``:: + + linaro-developer:~# ls -l /sys/bus/coresight/devices/tmc_etr0/connections + <file details> cti_sys0 -> ../../../20020000.cti/cti_sys0 + <file details> in:0 -> ../../../20120000.replicator/replicator0 + <file details> nr_links + +As described below, when using sysfs it is sufficient to enable a sink and +a source for successful trace. The framework will correctly enable all +intermediate links as required. + +Note: ``cti_sys0`` appears in two of the connections lists above. +CTIs can connect to multiple devices and are arranged in a star topology +via the CTM. See (:doc:`coresight-ect`) [#fourth]_ for further details. +Looking at this device we see 4 connections:: + + linaro-developer:~# ls -l /sys/bus/coresight/devices/cti_sys0/connections + <file details> nr_links + <file details> stm0 -> ../../../20100000.stm/stm0 + <file details> tmc_etf0 -> ../../../20010000.etf/tmc_etf0 + <file details> tmc_etr0 -> ../../../20070000.etr/tmc_etr0 + <file details> tpiu0 -> ../../../20030000.tpiu/tpiu0 + + +How to use the tracer modules +----------------------------- + +There are two ways to use the Coresight framework: + +1. using the perf cmd line tools. +2. interacting directly with the Coresight devices using the sysFS interface. + +Preference is given to the former as using the sysFS interface +requires a deep understanding of the Coresight HW. The following sections +provide details on using both methods. + +1) Using the sysFS interface: + +Before trace collection can start, a coresight sink needs to be identified. +There is no limit on the amount of sinks (nor sources) that can be enabled at +any given moment. As a generic operation, all device pertaining to the sink +class will have an "active" entry in sysfs:: + + root:/sys/bus/coresight/devices# ls + replicator 20030000.tpiu 2201c000.ptm 2203c000.etm 2203e000.etm + 20010000.etb 20040000.funnel 2201d000.ptm 2203d000.etm + root:/sys/bus/coresight/devices# ls 20010000.etb + enable_sink status trigger_cntr + root:/sys/bus/coresight/devices# echo 1 > 20010000.etb/enable_sink + root:/sys/bus/coresight/devices# cat 20010000.etb/enable_sink + 1 + root:/sys/bus/coresight/devices# + +At boot time the current etm3x driver will configure the first address +comparator with "_stext" and "_etext", essentially tracing any instruction +that falls within that range. As such "enabling" a source will immediately +trigger a trace capture:: + + root:/sys/bus/coresight/devices# echo 1 > 2201c000.ptm/enable_source + root:/sys/bus/coresight/devices# cat 2201c000.ptm/enable_source + 1 + root:/sys/bus/coresight/devices# cat 20010000.etb/status + Depth: 0x2000 + Status: 0x1 + RAM read ptr: 0x0 + RAM wrt ptr: 0x19d3 <----- The write pointer is moving + Trigger cnt: 0x0 + Control: 0x1 + Flush status: 0x0 + Flush ctrl: 0x2001 + root:/sys/bus/coresight/devices# + +Trace collection is stopped the same way:: + + root:/sys/bus/coresight/devices# echo 0 > 2201c000.ptm/enable_source + root:/sys/bus/coresight/devices# + +The content of the ETB buffer can be harvested directly from /dev:: + + root:/sys/bus/coresight/devices# dd if=/dev/20010000.etb \ + of=~/cstrace.bin + 64+0 records in + 64+0 records out + 32768 bytes (33 kB) copied, 0.00125258 s, 26.2 MB/s + root:/sys/bus/coresight/devices# + +The file cstrace.bin can be decompressed using "ptm2human", DS-5 or Trace32. + +Following is a DS-5 output of an experimental loop that increments a variable up +to a certain value. The example is simple and yet provides a glimpse of the +wealth of possibilities that coresight provides. +:: + + Info Tracing enabled + Instruction 106378866 0x8026B53C E52DE004 false PUSH {lr} + Instruction 0 0x8026B540 E24DD00C false SUB sp,sp,#0xc + Instruction 0 0x8026B544 E3A03000 false MOV r3,#0 + Instruction 0 0x8026B548 E58D3004 false STR r3,[sp,#4] + Instruction 0 0x8026B54C E59D3004 false LDR r3,[sp,#4] + Instruction 0 0x8026B550 E3530004 false CMP r3,#4 + Instruction 0 0x8026B554 E2833001 false ADD r3,r3,#1 + Instruction 0 0x8026B558 E58D3004 false STR r3,[sp,#4] + Instruction 0 0x8026B55C DAFFFFFA true BLE {pc}-0x10 ; 0x8026b54c + Timestamp Timestamp: 17106715833 + Instruction 319 0x8026B54C E59D3004 false LDR r3,[sp,#4] + Instruction 0 0x8026B550 E3530004 false CMP r3,#4 + Instruction 0 0x8026B554 E2833001 false ADD r3,r3,#1 + Instruction 0 0x8026B558 E58D3004 false STR r3,[sp,#4] + Instruction 0 0x8026B55C DAFFFFFA true BLE {pc}-0x10 ; 0x8026b54c + Instruction 9 0x8026B54C E59D3004 false LDR r3,[sp,#4] + Instruction 0 0x8026B550 E3530004 false CMP r3,#4 + Instruction 0 0x8026B554 E2833001 false ADD r3,r3,#1 + Instruction 0 0x8026B558 E58D3004 false STR r3,[sp,#4] + Instruction 0 0x8026B55C DAFFFFFA true BLE {pc}-0x10 ; 0x8026b54c + Instruction 7 0x8026B54C E59D3004 false LDR r3,[sp,#4] + Instruction 0 0x8026B550 E3530004 false CMP r3,#4 + Instruction 0 0x8026B554 E2833001 false ADD r3,r3,#1 + Instruction 0 0x8026B558 E58D3004 false STR r3,[sp,#4] + Instruction 0 0x8026B55C DAFFFFFA true BLE {pc}-0x10 ; 0x8026b54c + Instruction 7 0x8026B54C E59D3004 false LDR r3,[sp,#4] + Instruction 0 0x8026B550 E3530004 false CMP r3,#4 + Instruction 0 0x8026B554 E2833001 false ADD r3,r3,#1 + Instruction 0 0x8026B558 E58D3004 false STR r3,[sp,#4] + Instruction 0 0x8026B55C DAFFFFFA true BLE {pc}-0x10 ; 0x8026b54c + Instruction 10 0x8026B54C E59D3004 false LDR r3,[sp,#4] + Instruction 0 0x8026B550 E3530004 false CMP r3,#4 + Instruction 0 0x8026B554 E2833001 false ADD r3,r3,#1 + Instruction 0 0x8026B558 E58D3004 false STR r3,[sp,#4] + Instruction 0 0x8026B55C DAFFFFFA true BLE {pc}-0x10 ; 0x8026b54c + Instruction 6 0x8026B560 EE1D3F30 false MRC p15,#0x0,r3,c13,c0,#1 + Instruction 0 0x8026B564 E1A0100D false MOV r1,sp + Instruction 0 0x8026B568 E3C12D7F false BIC r2,r1,#0x1fc0 + Instruction 0 0x8026B56C E3C2203F false BIC r2,r2,#0x3f + Instruction 0 0x8026B570 E59D1004 false LDR r1,[sp,#4] + Instruction 0 0x8026B574 E59F0010 false LDR r0,[pc,#16] ; [0x8026B58C] = 0x80550368 + Instruction 0 0x8026B578 E592200C false LDR r2,[r2,#0xc] + Instruction 0 0x8026B57C E59221D0 false LDR r2,[r2,#0x1d0] + Instruction 0 0x8026B580 EB07A4CF true BL {pc}+0x1e9344 ; 0x804548c4 + Info Tracing enabled + Instruction 13570831 0x8026B584 E28DD00C false ADD sp,sp,#0xc + Instruction 0 0x8026B588 E8BD8000 true LDM sp!,{pc} + Timestamp Timestamp: 17107041535 + +2) Using perf framework: + +Coresight tracers are represented using the Perf framework's Performance +Monitoring Unit (PMU) abstraction. As such the perf framework takes charge of +controlling when tracing gets enabled based on when the process of interest is +scheduled. When configured in a system, Coresight PMUs will be listed when +queried by the perf command line tool: + + linaro@linaro-nano:~$ ./perf list pmu + + List of pre-defined events (to be used in -e): + + cs_etm// [Kernel PMU event] + + linaro@linaro-nano:~$ + +Regardless of the number of tracers available in a system (usually equal to the +amount of processor cores), the "cs_etm" PMU will be listed only once. + +A Coresight PMU works the same way as any other PMU, i.e the name of the PMU is +listed along with configuration options within forward slashes '/'. Since a +Coresight system will typically have more than one sink, the name of the sink to +work with needs to be specified as an event option. +On newer kernels the available sinks are listed in sysFS under +($SYSFS)/bus/event_source/devices/cs_etm/sinks/:: + + root@localhost:/sys/bus/event_source/devices/cs_etm/sinks# ls + tmc_etf0 tmc_etr0 tpiu0 + +On older kernels, this may need to be found from the list of coresight devices, +available under ($SYSFS)/bus/coresight/devices/:: + + root:~# ls /sys/bus/coresight/devices/ + etm0 etm1 etm2 etm3 etm4 etm5 funnel0 + funnel1 funnel2 replicator0 stm0 tmc_etf0 tmc_etr0 tpiu0 + root@linaro-nano:~# perf record -e cs_etm/@tmc_etr0/u --per-thread program + +As mentioned above in section "Device Naming scheme", the names of the devices could +look different from what is used in the example above. One must use the device names +as it appears under the sysFS. + +The syntax within the forward slashes '/' is important. The '@' character +tells the parser that a sink is about to be specified and that this is the sink +to use for the trace session. + +More information on the above and other example on how to use Coresight with +the perf tools can be found in the "HOWTO.md" file of the openCSD gitHub +repository [#third]_. + +2.1) AutoFDO analysis using the perf tools: + +perf can be used to record and analyze trace of programs. + +Execution can be recorded using 'perf record' with the cs_etm event, +specifying the name of the sink to record to, e.g:: + + perf record -e cs_etm/@tmc_etr0/u --per-thread + +The 'perf report' and 'perf script' commands can be used to analyze execution, +synthesizing instruction and branch events from the instruction trace. +'perf inject' can be used to replace the trace data with the synthesized events. +The --itrace option controls the type and frequency of synthesized events +(see perf documentation). + +Note that only 64-bit programs are currently supported - further work is +required to support instruction decode of 32-bit Arm programs. + + +Generating coverage files for Feedback Directed Optimization: AutoFDO +--------------------------------------------------------------------- + +'perf inject' accepts the --itrace option in which case tracing data is +removed and replaced with the synthesized events. e.g. +:: + + perf inject --itrace --strip -i perf.data -o perf.data.new + +Below is an example of using ARM ETM for autoFDO. It requires autofdo +(https://github.com/google/autofdo) and gcc version 5. The bubble +sort example is from the AutoFDO tutorial (https://gcc.gnu.org/wiki/AutoFDO/Tutorial). +:: + + $ gcc-5 -O3 sort.c -o sort + $ taskset -c 2 ./sort + Bubble sorting array of 30000 elements + 5910 ms + + $ perf record -e cs_etm/@tmc_etr0/u --per-thread taskset -c 2 ./sort + Bubble sorting array of 30000 elements + 12543 ms + [ perf record: Woken up 35 times to write data ] + [ perf record: Captured and wrote 69.640 MB perf.data ] + + $ perf inject -i perf.data -o inj.data --itrace=il64 --strip + $ create_gcov --binary=./sort --profile=inj.data --gcov=sort.gcov -gcov_version=1 + $ gcc-5 -O3 -fauto-profile=sort.gcov sort.c -o sort_autofdo + $ taskset -c 2 ./sort_autofdo + Bubble sorting array of 30000 elements + 5806 ms + + +How to use the STM module +------------------------- + +Using the System Trace Macrocell module is the same as the tracers - the only +difference is that clients are driving the trace capture rather +than the program flow through the code. + +As with any other CoreSight component, specifics about the STM tracer can be +found in sysfs with more information on each entry being found in [#first]_:: + + root@genericarmv8:~# ls /sys/bus/coresight/devices/stm0 + enable_source hwevent_select port_enable subsystem uevent + hwevent_enable mgmt port_select traceid + root@genericarmv8:~# + +Like any other source a sink needs to be identified and the STM enabled before +being used:: + + root@genericarmv8:~# echo 1 > /sys/bus/coresight/devices/tmc_etf0/enable_sink + root@genericarmv8:~# echo 1 > /sys/bus/coresight/devices/stm0/enable_source + +From there user space applications can request and use channels using the devfs +interface provided for that purpose by the generic STM API:: + + root@genericarmv8:~# ls -l /dev/stm0 + crw------- 1 root root 10, 61 Jan 3 18:11 /dev/stm0 + root@genericarmv8:~# + +Details on how to use the generic STM API can be found here:- :doc:`../stm` [#second]_. + +The CTI & CTM Modules +--------------------- + +The CTI (Cross Trigger Interface) provides a set of trigger signals between +individual CTIs and components, and can propagate these between all CTIs via +channels on the CTM (Cross Trigger Matrix). + +A separate documentation file is provided to explain the use of these devices. +(:doc:`coresight-ect`) [#fourth]_. + + +.. [#first] Documentation/ABI/testing/sysfs-bus-coresight-devices-stm + +.. [#second] Documentation/trace/stm.rst + +.. [#third] https://github.com/Linaro/perf-opencsd + +.. [#fourth] Documentation/trace/coresight/coresight-ect.rst diff --git a/Documentation/trace/coresight/index.rst b/Documentation/trace/coresight/index.rst new file mode 100644 index 000000000..8d31b155a --- /dev/null +++ b/Documentation/trace/coresight/index.rst @@ -0,0 +1,9 @@ +============================== +CoreSight - ARM Hardware Trace +============================== + +.. toctree:: + :maxdepth: 2 + :glob: + + * |