Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 460 insertions, 0 deletions

diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
new file mode 100644
index 000000000..6bd2228bb
--- /dev/null
+++ b/drivers/ata/pata_artop.c
@@ -0,0 +1,460 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *    pata_artop.c - ARTOP ATA controller driver
+ *
+ *	(C) 2006 Red Hat
+ *	(C) 2007,2011 Bartlomiej Zolnierkiewicz
+ *
+ *    Based in part on drivers/ide/pci/aec62xx.c
+ *	Copyright (C) 1999-2002	Andre Hedrick <andre@linux-ide.org>
+ *	865/865R fixes for Macintosh card version from a patch to the old
+ *		driver by Thibaut VARENE <varenet@parisc-linux.org>
+ *	When setting the PCI latency we must set 0x80 or higher for burst
+ *		performance Alessandro Zummo <alessandro.zummo@towertech.it>
+ *
+ *	TODO
+ *	Investigate no_dsc on 850R
+ *	Clock detect
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME	"pata_artop"
+#define DRV_VERSION	"0.4.6"
+
+/*
+ *	The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
+ *	get PCI bus speed functionality we leave this as 0. Its a variable
+ *	for when we get the functionality and also for folks wanting to
+ *	test stuff.
+ */
+
+static int clock = 0;
+
+/**
+ *	artop62x0_pre_reset	-	probe begin
+ *	@link: link
+ *	@deadline: deadline jiffies for the operation
+ *
+ *	Nothing complicated needed here.
+ */
+
+static int artop62x0_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+	static const struct pci_bits artop_enable_bits[] = {
+		{ 0x4AU, 1U, 0x02UL, 0x02UL },	/* port 0 */
+		{ 0x4AU, 1U, 0x04UL, 0x04UL },	/* port 1 */
+	};
+
+	struct ata_port *ap = link->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+	/* Odd numbered device ids are the units with enable bits. */
+	if ((pdev->device & 1) &&
+	    !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
+		return -ENOENT;
+
+	return ata_sff_prereset(link, deadline);
+}
+
+/**
+ *	artop6260_cable_detect	-	identify cable type
+ *	@ap: Port
+ *
+ *	Identify the cable type for the ARTOP interface in question
+ */
+
+static int artop6260_cable_detect(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u8 tmp;
+	pci_read_config_byte(pdev, 0x49, &tmp);
+	if (tmp & (1 << ap->port_no))
+		return ATA_CBL_PATA40;
+	return ATA_CBL_PATA80;
+}
+
+/**
+ *	artop6210_load_piomode - Load a set of PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device
+ *	@pio: PIO mode
+ *
+ *	Set PIO mode for device, in host controller PCI config space. This
+ *	is used both to set PIO timings in PIO mode and also to set the
+ *	matching PIO clocking for UDMA, as well as the MWDMA timings.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	static const u16 timing[2][5] = {
+		{ 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
+		{ 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }
+
+	};
+	/* Load the PIO timing active/recovery bits */
+	pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
+}
+
+/**
+ *	artop6210_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *
+ *	Set PIO mode for device, in host controller PCI config space. For
+ *	ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *	the event UDMA is used the later call to set_dmamode will set the
+ *	bits as required.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	u8 ultra;
+
+	artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+	pci_read_config_byte(pdev, 0x54, &ultra);
+	ultra &= ~(3 << (2 * dn));
+	pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *	artop6260_load_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *	@pio: PIO mode
+ *
+ *	Set PIO mode for device, in host controller PCI config space. The
+ *	ARTOP6260 and relatives store the timing data differently.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	static const u8 timing[2][5] = {
+		{ 0x00, 0x0A, 0x08, 0x33, 0x31 },
+		{ 0x70, 0x7A, 0x78, 0x43, 0x41 }
+
+	};
+	/* Load the PIO timing active/recovery bits */
+	pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
+}
+
+/**
+ *	artop6260_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *
+ *	Set PIO mode for device, in host controller PCI config space. For
+ *	ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *	the event UDMA is used the later call to set_dmamode will set the
+ *	bits as required.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	u8 ultra;
+
+	artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+	ultra &= ~(7 << (4  * adev->devno));	/* One nibble per drive */
+	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+/**
+ *	artop6210_set_dmamode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device whose timings we are configuring
+ *
+ *	Set DMA mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio;
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	u8 ultra;
+
+	if (adev->dma_mode == XFER_MW_DMA_0)
+		pio = 1;
+	else
+		pio = 4;
+
+	/* Load the PIO timing active/recovery bits */
+	artop6210_load_piomode(ap, adev, pio);
+
+	pci_read_config_byte(pdev, 0x54, &ultra);
+	ultra &= ~(3 << (2 * dn));
+
+	/* Add ultra DMA bits if in UDMA mode */
+	if (adev->dma_mode >= XFER_UDMA_0) {
+		u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
+		if (mode == 0)
+			mode = 1;
+		ultra |= (mode << (2 * dn));
+	}
+	pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *	artop6260_set_dmamode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *
+ *	Set DMA mode for device, in host controller PCI config space. The
+ *	ARTOP6260 and relatives store the timing data differently.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio;
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	u8 ultra;
+
+	if (adev->dma_mode == XFER_MW_DMA_0)
+		pio = 1;
+	else
+		pio = 4;
+
+	/* Load the PIO timing active/recovery bits */
+	artop6260_load_piomode(ap, adev, pio);
+
+	/* Add ultra DMA bits if in UDMA mode */
+	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+	ultra &= ~(7 << (4  * adev->devno));	/* One nibble per drive */
+	if (adev->dma_mode >= XFER_UDMA_0) {
+		u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
+		if (mode == 0)
+			mode = 1;
+		ultra |= (mode << (4 * adev->devno));
+	}
+	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+/**
+ *	artop_6210_qc_defer	-	implement serialization
+ *	@qc: command
+ *
+ *	Issue commands per host on this chip.
+ */
+
+static int artop6210_qc_defer(struct ata_queued_cmd *qc)
+{
+	struct ata_host *host = qc->ap->host;
+	struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
+	int rc;
+
+	/* First apply the usual rules */
+	rc = ata_std_qc_defer(qc);
+	if (rc != 0)
+		return rc;
+
+	/* Now apply serialization rules. Only allow a command if the
+	   other channel state machine is idle */
+	if (alt && alt->qc_active)
+		return	ATA_DEFER_PORT;
+	return 0;
+}
+
+static struct scsi_host_template artop_sht = {
+	ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations artop6210_ops = {
+	.inherits		= &ata_bmdma_port_ops,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= artop6210_set_piomode,
+	.set_dmamode		= artop6210_set_dmamode,
+	.prereset		= artop62x0_pre_reset,
+	.qc_defer		= artop6210_qc_defer,
+};
+
+static struct ata_port_operations artop6260_ops = {
+	.inherits		= &ata_bmdma_port_ops,
+	.cable_detect		= artop6260_cable_detect,
+	.set_piomode		= artop6260_set_piomode,
+	.set_dmamode		= artop6260_set_dmamode,
+	.prereset		= artop62x0_pre_reset,
+};
+
+static void atp8xx_fixup(struct pci_dev *pdev)
+{
+	if (pdev->device == 0x0005)
+		/* BIOS may have left us in UDMA, clear it before libata probe */
+		pci_write_config_byte(pdev, 0x54, 0);
+	else if (pdev->device == 0x0008 || pdev->device == 0x0009) {
+		u8 reg;
+
+		/* Mac systems come up with some registers not set as we
+		   will need them */
+
+		/* Clear reset & test bits */
+		pci_read_config_byte(pdev, 0x49, &reg);
+		pci_write_config_byte(pdev, 0x49, reg & ~0x30);
+
+		/* PCI latency must be > 0x80 for burst mode, tweak it
+		 * if required.
+		 */
+		pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &reg);
+		if (reg <= 0x80)
+			pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);
+
+		/* Enable IRQ output and burst mode */
+		pci_read_config_byte(pdev, 0x4a, &reg);
+		pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
+	}
+}
+
+/**
+ *	artop_init_one - Register ARTOP ATA PCI device with kernel services
+ *	@pdev: PCI device to register
+ *	@ent: Entry in artop_pci_tbl matching with @pdev
+ *
+ *	Called from kernel PCI layer.
+ *
+ *	LOCKING:
+ *	Inherited from PCI layer (may sleep).
+ *
+ *	RETURNS:
+ *	Zero on success, or -ERRNO value.
+ */
+
+static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	static const struct ata_port_info info_6210 = {
+		.flags		= ATA_FLAG_SLAVE_POSS,
+		.pio_mask	= ATA_PIO4,
+		.mwdma_mask	= ATA_MWDMA2,
+		.udma_mask 	= ATA_UDMA2,
+		.port_ops	= &artop6210_ops,
+	};
+	static const struct ata_port_info info_626x = {
+		.flags		= ATA_FLAG_SLAVE_POSS,
+		.pio_mask	= ATA_PIO4,
+		.mwdma_mask	= ATA_MWDMA2,
+		.udma_mask 	= ATA_UDMA4,
+		.port_ops	= &artop6260_ops,
+	};
+	static const struct ata_port_info info_628x = {
+		.flags		= ATA_FLAG_SLAVE_POSS,
+		.pio_mask	= ATA_PIO4,
+		.mwdma_mask	= ATA_MWDMA2,
+		.udma_mask 	= ATA_UDMA5,
+		.port_ops	= &artop6260_ops,
+	};
+	static const struct ata_port_info info_628x_fast = {
+		.flags		= ATA_FLAG_SLAVE_POSS,
+		.pio_mask	= ATA_PIO4,
+		.mwdma_mask	= ATA_MWDMA2,
+		.udma_mask 	= ATA_UDMA6,
+		.port_ops	= &artop6260_ops,
+	};
+	const struct ata_port_info *ppi[] = { NULL, NULL };
+	int rc;
+
+	ata_print_version_once(&pdev->dev, DRV_VERSION);
+
+	rc = pcim_enable_device(pdev);
+	if (rc)
+		return rc;
+
+	if (id->driver_data == 0)	/* 6210 variant */
+		ppi[0] = &info_6210;
+	else if (id->driver_data == 1)	/* 6260 */
+		ppi[0] = &info_626x;
+	else if (id->driver_data == 2)	{ /* 6280 or 6280 + fast */
+		unsigned long io = pci_resource_start(pdev, 4);
+
+		ppi[0] = &info_628x;
+		if (inb(io) & 0x10)
+			ppi[0] = &info_628x_fast;
+	}
+
+	BUG_ON(ppi[0] == NULL);
+
+	atp8xx_fixup(pdev);
+
+	return ata_pci_bmdma_init_one(pdev, ppi, &artop_sht, NULL, 0);
+}
+
+static const struct pci_device_id artop_pci_tbl[] = {
+	{ PCI_VDEVICE(ARTOP, 0x0005), 0 },
+	{ PCI_VDEVICE(ARTOP, 0x0006), 1 },
+	{ PCI_VDEVICE(ARTOP, 0x0007), 1 },
+	{ PCI_VDEVICE(ARTOP, 0x0008), 2 },
+	{ PCI_VDEVICE(ARTOP, 0x0009), 2 },
+
+	{ }	/* terminate list */
+};
+
+#ifdef CONFIG_PM_SLEEP
+static int atp8xx_reinit_one(struct pci_dev *pdev)
+{
+	struct ata_host *host = pci_get_drvdata(pdev);
+	int rc;
+
+	rc = ata_pci_device_do_resume(pdev);
+	if (rc)
+		return rc;
+
+	atp8xx_fixup(pdev);
+
+	ata_host_resume(host);
+	return 0;
+}
+#endif
+
+static struct pci_driver artop_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= artop_pci_tbl,
+	.probe			= artop_init_one,
+	.remove			= ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+	.suspend		= ata_pci_device_suspend,
+	.resume			= atp8xx_reinit_one,
+#endif
+};
+
+module_pci_driver(artop_pci_driver);
+
+MODULE_AUTHOR("Alan Cox, Bartlomiej Zolnierkiewicz");
+MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
+MODULE_VERSION(DRV_VERSION);