Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 446 insertions, 0 deletions

diff --git a/drivers/ide/qd65xx.c b/drivers/ide/qd65xx.c
new file mode 100644
index 000000000..ab79b6289
--- /dev/null
+++ b/drivers/ide/qd65xx.c
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 1996-2001  Linus Torvalds & author (see below)
+ */
+
+/*
+ *  Version 0.03	Cleaned auto-tune, added probe
+ *  Version 0.04	Added second channel tuning
+ *  Version 0.05	Enhanced tuning ; added qd6500 support
+ *  Version 0.06	Added dos driver's list
+ *  Version 0.07	Second channel bug fix 
+ *
+ * QDI QD6500/QD6580 EIDE controller fast support
+ *
+ * To activate controller support, use "ide0=qd65xx"
+ */
+
+/*
+ * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by
+ * Samuel Thibault <samuel.thibault@ens-lyon.org>
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+#include <asm/io.h>
+
+#define DRV_NAME "qd65xx"
+
+#include "qd65xx.h"
+
+/*
+ * I/O ports are 0x30-0x31 (and 0x32-0x33 for qd6580)
+ *            or 0xb0-0xb1 (and 0xb2-0xb3 for qd6580)
+ *	-- qd6500 is a single IDE interface
+ *	-- qd6580 is a dual IDE interface
+ *
+ * More research on qd6580 being done by willmore@cig.mot.com (David)
+ * More Information given by Petr Soucek (petr@ryston.cz)
+ * http://www.ryston.cz/petr/vlb
+ */
+
+/*
+ * base: Timer1
+ *
+ *
+ * base+0x01: Config (R/O)
+ *
+ * bit 0: ide baseport: 1 = 0x1f0 ; 0 = 0x170 (only useful for qd6500)
+ * bit 1: qd65xx baseport: 1 = 0xb0 ; 0 = 0x30
+ * bit 2: ID3: bus speed: 1 = <=33MHz ; 0 = >33MHz
+ * bit 3: qd6500: 1 = disabled, 0 = enabled
+ *        qd6580: 1
+ * upper nibble:
+ *        qd6500: 1100
+ *        qd6580: either 1010 or 0101
+ *
+ *
+ * base+0x02: Timer2 (qd6580 only)
+ *
+ *
+ * base+0x03: Control (qd6580 only)
+ *
+ * bits 0-3 must always be set 1
+ * bit 4 must be set 1, but is set 0 by dos driver while measuring vlb clock
+ * bit 0 : 1 = Only primary port enabled : channel 0 for hda, channel 1 for hdb
+ *         0 = Primary and Secondary ports enabled : channel 0 for hda & hdb
+ *                                                   channel 1 for hdc & hdd
+ * bit 1 : 1 = only disks on primary port
+ *         0 = disks & ATAPI devices on primary port
+ * bit 2-4 : always 0
+ * bit 5 : status, but of what ?
+ * bit 6 : always set 1 by dos driver
+ * bit 7 : set 1 for non-ATAPI devices on primary port
+ *	(maybe read-ahead and post-write buffer ?)
+ */
+
+static int timings[4]={-1,-1,-1,-1}; /* stores current timing for each timer */
+
+/*
+ * qd65xx_select:
+ *
+ * This routine is invoked to prepare for access to a given drive.
+ */
+
+static void qd65xx_dev_select(ide_drive_t *drive)
+{
+	u8 index = ((	(QD_TIMREG(drive)) & 0x80 ) >> 7) |
+			(QD_TIMREG(drive) & 0x02);
+
+	if (timings[index] != QD_TIMING(drive))
+		outb(timings[index] = QD_TIMING(drive), QD_TIMREG(drive));
+
+	outb(drive->select | ATA_DEVICE_OBS, drive->hwif->io_ports.device_addr);
+}
+
+/*
+ * qd6500_compute_timing
+ *
+ * computes the timing value where
+ *	lower nibble represents active time,   in count of VLB clocks
+ *	upper nibble represents recovery time, in count of VLB clocks
+ */
+
+static u8 qd6500_compute_timing (ide_hwif_t *hwif, int active_time, int recovery_time)
+{
+	int clk = ide_vlb_clk ? ide_vlb_clk : 50;
+	u8 act_cyc, rec_cyc;
+
+	if (clk <= 33) {
+		act_cyc =  9 - IDE_IN(active_time   * clk / 1000 + 1, 2,  9);
+		rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 0, 15);
+	} else {
+		act_cyc =  8 - IDE_IN(active_time   * clk / 1000 + 1, 1,  8);
+		rec_cyc = 18 - IDE_IN(recovery_time * clk / 1000 + 1, 3, 18);
+	}
+
+	return (rec_cyc << 4) | 0x08 | act_cyc;
+}
+
+/*
+ * qd6580_compute_timing
+ *
+ * idem for qd6580
+ */
+
+static u8 qd6580_compute_timing (int active_time, int recovery_time)
+{
+	int clk = ide_vlb_clk ? ide_vlb_clk : 50;
+	u8 act_cyc, rec_cyc;
+
+	act_cyc = 17 - IDE_IN(active_time   * clk / 1000 + 1, 2, 17);
+	rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 2, 15);
+
+	return (rec_cyc << 4) | act_cyc;
+}
+
+/*
+ * qd_find_disk_type
+ *
+ * tries to find timing from dos driver's table
+ */
+
+static int qd_find_disk_type (ide_drive_t *drive,
+		int *active_time, int *recovery_time)
+{
+	struct qd65xx_timing_s *p;
+	char *m = (char *)&drive->id[ATA_ID_PROD];
+	char model[ATA_ID_PROD_LEN];
+
+	if (*m == 0)
+		return 0;
+
+	strncpy(model, m, ATA_ID_PROD_LEN);
+	ide_fixstring(model, ATA_ID_PROD_LEN, 1); /* byte-swap */
+
+	for (p = qd65xx_timing ; p->offset != -1 ; p++) {
+		if (!strncmp(p->model, model+p->offset, 4)) {
+			printk(KERN_DEBUG "%s: listed !\n", drive->name);
+			*active_time = p->active;
+			*recovery_time = p->recovery;
+			return 1;
+		}
+	}
+	return 0;
+}
+
+/*
+ * qd_set_timing:
+ *
+ * records the timing
+ */
+
+static void qd_set_timing (ide_drive_t *drive, u8 timing)
+{
+	unsigned long data = (unsigned long)ide_get_drivedata(drive);
+
+	data &= 0xff00;
+	data |= timing;
+	ide_set_drivedata(drive, (void *)data);
+
+	printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
+}
+
+static void qd6500_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+	u16 *id = drive->id;
+	int active_time   = 175;
+	int recovery_time = 415; /* worst case values from the dos driver */
+
+	/* FIXME: use drive->pio_mode value */
+	if (!qd_find_disk_type(drive, &active_time, &recovery_time) &&
+	    (id[ATA_ID_OLD_PIO_MODES] & 0xff) && (id[ATA_ID_FIELD_VALID] & 2) &&
+	    id[ATA_ID_EIDE_PIO] >= 240) {
+		printk(KERN_INFO "%s: PIO mode%d\n", drive->name,
+			id[ATA_ID_OLD_PIO_MODES] & 0xff);
+		active_time = 110;
+		recovery_time = drive->id[ATA_ID_EIDE_PIO] - 120;
+	}
+
+	qd_set_timing(drive, qd6500_compute_timing(drive->hwif,
+				active_time, recovery_time));
+}
+
+static void qd6580_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
+	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
+	unsigned int cycle_time;
+	int active_time   = 175;
+	int recovery_time = 415; /* worst case values from the dos driver */
+	u8 base = (hwif->config_data & 0xff00) >> 8;
+
+	if (drive->id && !qd_find_disk_type(drive, &active_time, &recovery_time)) {
+		cycle_time = ide_pio_cycle_time(drive, pio);
+
+		switch (pio) {
+			case 0: break;
+			case 3:
+				if (cycle_time >= 110) {
+					active_time = 86;
+					recovery_time = cycle_time - 102;
+				} else
+					printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
+				break;
+			case 4:
+				if (cycle_time >= 69) {
+					active_time = 70;
+					recovery_time = cycle_time - 61;
+				} else
+					printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
+				break;
+			default:
+				if (cycle_time >= 180) {
+					active_time = 110;
+					recovery_time = cycle_time - 120;
+				} else {
+					active_time = t->active;
+					recovery_time = cycle_time - active_time;
+				}
+		}
+		printk(KERN_INFO "%s: PIO mode%d\n", drive->name,pio);
+	}
+
+	if (!hwif->channel && drive->media != ide_disk) {
+		outb(0x5f, QD_CONTROL_PORT);
+		printk(KERN_WARNING "%s: ATAPI: disabled read-ahead FIFO "
+			"and post-write buffer on %s.\n",
+			drive->name, hwif->name);
+	}
+
+	qd_set_timing(drive, qd6580_compute_timing(active_time, recovery_time));
+}
+
+/*
+ * qd_testreg
+ *
+ * tests if the given port is a register
+ */
+
+static int __init qd_testreg(int port)
+{
+	unsigned long flags;
+	u8 savereg, readreg;
+
+	local_irq_save(flags);
+	savereg = inb_p(port);
+	outb_p(QD_TESTVAL, port);	/* safe value */
+	readreg = inb_p(port);
+	outb(savereg, port);
+	local_irq_restore(flags);
+
+	if (savereg == QD_TESTVAL) {
+		printk(KERN_ERR "Outch ! the probe for qd65xx isn't reliable !\n");
+		printk(KERN_ERR "Please contact maintainers to tell about your hardware\n");
+		printk(KERN_ERR "Assuming qd65xx is not present.\n");
+		return 1;
+	}
+
+	return (readreg != QD_TESTVAL);
+}
+
+static void __init qd6500_init_dev(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	u8 base = (hwif->config_data & 0xff00) >> 8;
+	u8 config = QD_CONFIG(hwif);
+
+	ide_set_drivedata(drive, (void *)QD6500_DEF_DATA);
+}
+
+static void __init qd6580_init_dev(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	unsigned long t1, t2;
+	u8 base = (hwif->config_data & 0xff00) >> 8;
+	u8 config = QD_CONFIG(hwif);
+
+	if (hwif->host_flags & IDE_HFLAG_SINGLE) {
+		t1 = QD6580_DEF_DATA;
+		t2 = QD6580_DEF_DATA2;
+	} else
+		t2 = t1 = hwif->channel ? QD6580_DEF_DATA2 : QD6580_DEF_DATA;
+
+	ide_set_drivedata(drive, (void *)((drive->dn & 1) ? t2 : t1));
+}
+
+static const struct ide_tp_ops qd65xx_tp_ops = {
+	.exec_command		= ide_exec_command,
+	.read_status		= ide_read_status,
+	.read_altstatus		= ide_read_altstatus,
+	.write_devctl		= ide_write_devctl,
+
+	.dev_select		= qd65xx_dev_select,
+	.tf_load		= ide_tf_load,
+	.tf_read		= ide_tf_read,
+
+	.input_data		= ide_input_data,
+	.output_data		= ide_output_data,
+};
+
+static const struct ide_port_ops qd6500_port_ops = {
+	.init_dev		= qd6500_init_dev,
+	.set_pio_mode		= qd6500_set_pio_mode,
+};
+
+static const struct ide_port_ops qd6580_port_ops = {
+	.init_dev		= qd6580_init_dev,
+	.set_pio_mode		= qd6580_set_pio_mode,
+};
+
+static const struct ide_port_info qd65xx_port_info __initconst = {
+	.name			= DRV_NAME,
+	.tp_ops 		= &qd65xx_tp_ops,
+	.chipset		= ide_qd65xx,
+	.host_flags		= IDE_HFLAG_IO_32BIT |
+				  IDE_HFLAG_NO_DMA,
+	.pio_mask		= ATA_PIO4,
+};
+
+/*
+ * qd_probe:
+ *
+ * looks at the specified baseport, and if qd found, registers & initialises it
+ * return 1 if another qd may be probed
+ */
+
+static int __init qd_probe(int base)
+{
+	int rc;
+	u8 config, unit, control;
+	struct ide_port_info d = qd65xx_port_info;
+
+	config = inb(QD_CONFIG_PORT);
+
+	if (! ((config & QD_CONFIG_BASEPORT) >> 1 == (base == 0xb0)) )
+		return -ENODEV;
+
+	unit = ! (config & QD_CONFIG_IDE_BASEPORT);
+
+	if (unit)
+		d.host_flags |= IDE_HFLAG_QD_2ND_PORT;
+
+	switch (config & 0xf0) {
+	case QD_CONFIG_QD6500:
+		if (qd_testreg(base))
+			 return -ENODEV;	/* bad register */
+
+		if (config & QD_CONFIG_DISABLED) {
+			printk(KERN_WARNING "qd6500 is disabled !\n");
+			return -ENODEV;
+		}
+
+		printk(KERN_NOTICE "qd6500 at %#x\n", base);
+		printk(KERN_DEBUG "qd6500: config=%#x, ID3=%u\n",
+			config, QD_ID3);
+
+		d.port_ops = &qd6500_port_ops;
+		d.host_flags |= IDE_HFLAG_SINGLE;
+		break;
+	case QD_CONFIG_QD6580_A:
+	case QD_CONFIG_QD6580_B:
+		if (qd_testreg(base) || qd_testreg(base + 0x02))
+			return -ENODEV;	/* bad registers */
+
+		control = inb(QD_CONTROL_PORT);
+
+		printk(KERN_NOTICE "qd6580 at %#x\n", base);
+		printk(KERN_DEBUG "qd6580: config=%#x, control=%#x, ID3=%u\n",
+			config, control, QD_ID3);
+
+		outb(QD_DEF_CONTR, QD_CONTROL_PORT);
+
+		d.port_ops = &qd6580_port_ops;
+		if (control & QD_CONTR_SEC_DISABLED)
+			d.host_flags |= IDE_HFLAG_SINGLE;
+
+		printk(KERN_INFO "qd6580: %s IDE board\n",
+			(control & QD_CONTR_SEC_DISABLED) ? "single" : "dual");
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	rc = ide_legacy_device_add(&d, (base << 8) | config);
+
+	if (d.host_flags & IDE_HFLAG_SINGLE)
+		return (rc == 0) ? 1 : rc;
+
+	return rc;
+}
+
+static bool probe_qd65xx;
+
+module_param_named(probe, probe_qd65xx, bool, 0);
+MODULE_PARM_DESC(probe, "probe for QD65xx chipsets");
+
+static int __init qd65xx_init(void)
+{
+	int rc1, rc2 = -ENODEV;
+
+	if (probe_qd65xx == 0)
+		return -ENODEV;
+
+	rc1 = qd_probe(0x30);
+	if (rc1)
+		rc2 = qd_probe(0xb0);
+
+	if (rc1 < 0 && rc2 < 0)
+		return -ENODEV;
+
+	return 0;
+}
+
+module_init(qd65xx_init);
+
+MODULE_AUTHOR("Samuel Thibault");
+MODULE_DESCRIPTION("support of qd65xx vlb ide chipset");
+MODULE_LICENSE("GPL");