Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 385 insertions, 0 deletions

diff --git a/drivers/net/can/sja1000/kvaser_pci.c b/drivers/net/can/sja1000/kvaser_pci.c
new file mode 100644
index 000000000..0ea6b711c
--- /dev/null
+++ b/drivers/net/can/sja1000/kvaser_pci.c
@@ -0,0 +1,385 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2008 Per Dalen <per.dalen@cnw.se>
+ *
+ * Parts of this software are based on (derived) the following:
+ *
+ * - Kvaser linux driver, version 4.72 BETA
+ *   Copyright (C) 2002-2007 KVASER AB
+ *
+ * - Lincan driver, version 0.3.3, OCERA project
+ *   Copyright (C) 2004 Pavel Pisa
+ *   Copyright (C) 2001 Arnaud Westenberg
+ *
+ * - Socketcan SJA1000 drivers
+ *   Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
+ *   Copyright (c) 2002-2007 Volkswagen Group Electronic Research
+ *   Copyright (c) 2003 Matthias Brukner, Trajet Gmbh, Rebenring 33,
+ *   38106 Braunschweig, GERMANY
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/can/dev.h>
+#include <linux/io.h>
+
+#include "sja1000.h"
+
+#define DRV_NAME  "kvaser_pci"
+
+MODULE_AUTHOR("Per Dalen <per.dalen@cnw.se>");
+MODULE_DESCRIPTION("Socket-CAN driver for KVASER PCAN PCI cards");
+MODULE_SUPPORTED_DEVICE("KVASER PCAN PCI CAN card");
+MODULE_LICENSE("GPL v2");
+
+#define MAX_NO_OF_CHANNELS        4 /* max no of channels on a single card */
+
+struct kvaser_pci {
+	int channel;
+	struct pci_dev *pci_dev;
+	struct net_device *slave_dev[MAX_NO_OF_CHANNELS-1];
+	void __iomem *conf_addr;
+	void __iomem *res_addr;
+	int no_channels;
+	u8 xilinx_ver;
+};
+
+#define KVASER_PCI_CAN_CLOCK      (16000000 / 2)
+
+/*
+ * The board configuration is probably following:
+ * RX1 is connected to ground.
+ * TX1 is not connected.
+ * CLKO is not connected.
+ * Setting the OCR register to 0xDA is a good idea.
+ * This means  normal output mode , push-pull and the correct polarity.
+ */
+#define KVASER_PCI_OCR            (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
+
+/*
+ * In the CDR register, you should set CBP to 1.
+ * You will probably also want to set the clock divider value to 0
+ * (meaning divide-by-2), the Pelican bit, and the clock-off bit
+ * (you will have no need for CLKOUT anyway).
+ */
+#define KVASER_PCI_CDR            (CDR_CBP | CDR_CLKOUT_MASK)
+
+/*
+ * These register values are valid for revision 14 of the Xilinx logic.
+ */
+#define XILINX_VERINT             7   /* Lower nibble simulate interrupts,
+					 high nibble version number. */
+
+#define XILINX_PRESUMED_VERSION   14
+
+/*
+ * Important S5920 registers
+ */
+#define S5920_INTCSR              0x38
+#define S5920_PTCR                0x60
+#define INTCSR_ADDON_INTENABLE_M  0x2000
+
+
+#define KVASER_PCI_PORT_BYTES     0x20
+
+#define PCI_CONFIG_PORT_SIZE      0x80      /* size of the config io-memory */
+#define PCI_PORT_SIZE             0x80      /* size of a channel io-memory */
+#define PCI_PORT_XILINX_SIZE      0x08      /* size of a xilinx io-memory */
+
+#define KVASER_PCI_VENDOR_ID1     0x10e8    /* the PCI device and vendor IDs */
+#define KVASER_PCI_DEVICE_ID1     0x8406
+
+#define KVASER_PCI_VENDOR_ID2     0x1a07    /* the PCI device and vendor IDs */
+#define KVASER_PCI_DEVICE_ID2     0x0008
+
+static const struct pci_device_id kvaser_pci_tbl[] = {
+	{KVASER_PCI_VENDOR_ID1, KVASER_PCI_DEVICE_ID1, PCI_ANY_ID, PCI_ANY_ID,},
+	{KVASER_PCI_VENDOR_ID2, KVASER_PCI_DEVICE_ID2, PCI_ANY_ID, PCI_ANY_ID,},
+	{ 0,}
+};
+
+MODULE_DEVICE_TABLE(pci, kvaser_pci_tbl);
+
+static u8 kvaser_pci_read_reg(const struct sja1000_priv *priv, int port)
+{
+	return ioread8(priv->reg_base + port);
+}
+
+static void kvaser_pci_write_reg(const struct sja1000_priv *priv,
+				 int port, u8 val)
+{
+	iowrite8(val, priv->reg_base + port);
+}
+
+static void kvaser_pci_disable_irq(struct net_device *dev)
+{
+	struct sja1000_priv *priv = netdev_priv(dev);
+	struct kvaser_pci *board = priv->priv;
+	u32 intcsr;
+
+	/* Disable interrupts from card */
+	intcsr = ioread32(board->conf_addr + S5920_INTCSR);
+	intcsr &= ~INTCSR_ADDON_INTENABLE_M;
+	iowrite32(intcsr, board->conf_addr + S5920_INTCSR);
+}
+
+static void kvaser_pci_enable_irq(struct net_device *dev)
+{
+	struct sja1000_priv *priv = netdev_priv(dev);
+	struct kvaser_pci *board = priv->priv;
+	u32 tmp_en_io;
+
+	/* Enable interrupts from card */
+	tmp_en_io = ioread32(board->conf_addr + S5920_INTCSR);
+	tmp_en_io |= INTCSR_ADDON_INTENABLE_M;
+	iowrite32(tmp_en_io, board->conf_addr + S5920_INTCSR);
+}
+
+static int number_of_sja1000_chip(void __iomem *base_addr)
+{
+	u8 status;
+	int i;
+
+	for (i = 0; i < MAX_NO_OF_CHANNELS; i++) {
+		/* reset chip */
+		iowrite8(MOD_RM, base_addr +
+			 (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
+		status = ioread8(base_addr +
+				 (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
+		/* check reset bit */
+		if (!(status & MOD_RM))
+			break;
+	}
+
+	return i;
+}
+
+static void kvaser_pci_del_chan(struct net_device *dev)
+{
+	struct sja1000_priv *priv;
+	struct kvaser_pci *board;
+	int i;
+
+	if (!dev)
+		return;
+	priv = netdev_priv(dev);
+	board = priv->priv;
+	if (!board)
+		return;
+
+	dev_info(&board->pci_dev->dev, "Removing device %s\n",
+		 dev->name);
+
+	/* Disable PCI interrupts */
+	kvaser_pci_disable_irq(dev);
+
+	for (i = 0; i < board->no_channels - 1; i++) {
+		if (board->slave_dev[i]) {
+			dev_info(&board->pci_dev->dev, "Removing device %s\n",
+				 board->slave_dev[i]->name);
+			unregister_sja1000dev(board->slave_dev[i]);
+			free_sja1000dev(board->slave_dev[i]);
+		}
+	}
+	unregister_sja1000dev(dev);
+
+	pci_iounmap(board->pci_dev, priv->reg_base);
+	pci_iounmap(board->pci_dev, board->conf_addr);
+	pci_iounmap(board->pci_dev, board->res_addr);
+
+	free_sja1000dev(dev);
+}
+
+static int kvaser_pci_add_chan(struct pci_dev *pdev, int channel,
+			       struct net_device **master_dev,
+			       void __iomem *conf_addr,
+			       void __iomem *res_addr,
+			       void __iomem *base_addr)
+{
+	struct net_device *dev;
+	struct sja1000_priv *priv;
+	struct kvaser_pci *board;
+	int err;
+
+	dev = alloc_sja1000dev(sizeof(struct kvaser_pci));
+	if (dev == NULL)
+		return -ENOMEM;
+
+	priv = netdev_priv(dev);
+	board = priv->priv;
+
+	board->pci_dev = pdev;
+	board->channel = channel;
+
+	/* S5920 */
+	board->conf_addr = conf_addr;
+
+	/* XILINX board wide address */
+	board->res_addr = res_addr;
+
+	if (channel == 0) {
+		board->xilinx_ver =
+			ioread8(board->res_addr + XILINX_VERINT) >> 4;
+
+		/* Assert PTADR# - we're in passive mode so the other bits are
+		   not important */
+		iowrite32(0x80808080UL, board->conf_addr + S5920_PTCR);
+
+		/* Enable interrupts from card */
+		kvaser_pci_enable_irq(dev);
+	} else {
+		struct sja1000_priv *master_priv = netdev_priv(*master_dev);
+		struct kvaser_pci *master_board = master_priv->priv;
+		master_board->slave_dev[channel - 1] = dev;
+		master_board->no_channels = channel + 1;
+		board->xilinx_ver = master_board->xilinx_ver;
+	}
+
+	priv->reg_base = base_addr + channel * KVASER_PCI_PORT_BYTES;
+
+	priv->read_reg = kvaser_pci_read_reg;
+	priv->write_reg = kvaser_pci_write_reg;
+
+	priv->can.clock.freq = KVASER_PCI_CAN_CLOCK;
+
+	priv->ocr = KVASER_PCI_OCR;
+	priv->cdr = KVASER_PCI_CDR;
+
+	priv->irq_flags = IRQF_SHARED;
+	dev->irq = pdev->irq;
+
+	dev_info(&pdev->dev, "reg_base=%p conf_addr=%p irq=%d\n",
+		 priv->reg_base, board->conf_addr, dev->irq);
+
+	SET_NETDEV_DEV(dev, &pdev->dev);
+	dev->dev_id = channel;
+
+	/* Register SJA1000 device */
+	err = register_sja1000dev(dev);
+	if (err) {
+		dev_err(&pdev->dev, "Registering device failed (err=%d)\n",
+			err);
+		goto failure;
+	}
+
+	if (channel == 0)
+		*master_dev = dev;
+
+	return 0;
+
+failure:
+	kvaser_pci_del_chan(dev);
+	return err;
+}
+
+static int kvaser_pci_init_one(struct pci_dev *pdev,
+			       const struct pci_device_id *ent)
+{
+	int err;
+	struct net_device *master_dev = NULL;
+	struct sja1000_priv *priv;
+	struct kvaser_pci *board;
+	int no_channels;
+	void __iomem *base_addr = NULL;
+	void __iomem *conf_addr = NULL;
+	void __iomem *res_addr = NULL;
+	int i;
+
+	dev_info(&pdev->dev, "initializing device %04x:%04x\n",
+		 pdev->vendor, pdev->device);
+
+	err = pci_enable_device(pdev);
+	if (err)
+		goto failure;
+
+	err = pci_request_regions(pdev, DRV_NAME);
+	if (err)
+		goto failure_release_pci;
+
+	/* S5920 */
+	conf_addr = pci_iomap(pdev, 0, PCI_CONFIG_PORT_SIZE);
+	if (conf_addr == NULL) {
+		err = -ENODEV;
+		goto failure_release_regions;
+	}
+
+	/* XILINX board wide address */
+	res_addr = pci_iomap(pdev, 2, PCI_PORT_XILINX_SIZE);
+	if (res_addr == NULL) {
+		err = -ENOMEM;
+		goto failure_iounmap;
+	}
+
+	base_addr = pci_iomap(pdev, 1, PCI_PORT_SIZE);
+	if (base_addr == NULL) {
+		err = -ENOMEM;
+		goto failure_iounmap;
+	}
+
+	no_channels = number_of_sja1000_chip(base_addr);
+	if (no_channels == 0) {
+		err = -ENOMEM;
+		goto failure_iounmap;
+	}
+
+	for (i = 0; i < no_channels; i++) {
+		err = kvaser_pci_add_chan(pdev, i, &master_dev,
+					  conf_addr, res_addr,
+					  base_addr);
+		if (err)
+			goto failure_cleanup;
+	}
+
+	priv = netdev_priv(master_dev);
+	board = priv->priv;
+
+	dev_info(&pdev->dev, "xilinx version=%d number of channels=%d\n",
+		 board->xilinx_ver, board->no_channels);
+
+	pci_set_drvdata(pdev, master_dev);
+	return 0;
+
+failure_cleanup:
+	kvaser_pci_del_chan(master_dev);
+
+failure_iounmap:
+	if (conf_addr != NULL)
+		pci_iounmap(pdev, conf_addr);
+	if (res_addr != NULL)
+		pci_iounmap(pdev, res_addr);
+	if (base_addr != NULL)
+		pci_iounmap(pdev, base_addr);
+
+failure_release_regions:
+	pci_release_regions(pdev);
+
+failure_release_pci:
+	pci_disable_device(pdev);
+
+failure:
+	return err;
+
+}
+
+static void kvaser_pci_remove_one(struct pci_dev *pdev)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+
+	kvaser_pci_del_chan(dev);
+
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
+}
+
+static struct pci_driver kvaser_pci_driver = {
+	.name = DRV_NAME,
+	.id_table = kvaser_pci_tbl,
+	.probe = kvaser_pci_init_one,
+	.remove = kvaser_pci_remove_one,
+};
+
+module_pci_driver(kvaser_pci_driver);