Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 498 insertions, 0 deletions

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
new file mode 100644
index 000000000..50ef68497
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -0,0 +1,498 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Amlogic Meson8b, Meson8m2 and GXBB DWMAC glue layer
+ *
+ * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/ethtool.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_net.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+#include <linux/stmmac.h>
+
+#include "stmmac_platform.h"
+
+#define PRG_ETH0			0x0
+
+#define PRG_ETH0_RGMII_MODE		BIT(0)
+
+#define PRG_ETH0_EXT_PHY_MODE_MASK	GENMASK(2, 0)
+#define PRG_ETH0_EXT_RGMII_MODE		1
+#define PRG_ETH0_EXT_RMII_MODE		4
+
+/* mux to choose between fclk_div2 (bit unset) and mpll2 (bit set) */
+#define PRG_ETH0_CLK_M250_SEL_MASK	GENMASK(4, 4)
+
+/* TX clock delay in ns = "8ns / 4 * tx_dly_val" (where 8ns are exactly one
+ * cycle of the 125MHz RGMII TX clock):
+ * 0ns = 0x0, 2ns = 0x1, 4ns = 0x2, 6ns = 0x3
+ */
+#define PRG_ETH0_TXDLY_MASK		GENMASK(6, 5)
+
+/* divider for the result of m250_sel */
+#define PRG_ETH0_CLK_M250_DIV_SHIFT	7
+#define PRG_ETH0_CLK_M250_DIV_WIDTH	3
+
+#define PRG_ETH0_RGMII_TX_CLK_EN	10
+
+#define PRG_ETH0_INVERTED_RMII_CLK	BIT(11)
+#define PRG_ETH0_TX_AND_PHY_REF_CLK	BIT(12)
+
+/* Bypass (= 0, the signal from the GPIO input directly connects to the
+ * internal sampling) or enable (= 1) the internal logic for RXEN and RXD[3:0]
+ * timing tuning.
+ */
+#define PRG_ETH0_ADJ_ENABLE		BIT(13)
+/* Controls whether the RXEN and RXD[3:0] signals should be aligned with the
+ * input RX rising/falling edge and sent to the Ethernet internals. This sets
+ * the automatically delay and skew automatically (internally).
+ */
+#define PRG_ETH0_ADJ_SETUP		BIT(14)
+/* An internal counter based on the "timing-adjustment" clock. The counter is
+ * cleared on both, the falling and rising edge of the RX_CLK. This selects the
+ * delay (= the counter value) when to start sampling RXEN and RXD[3:0].
+ */
+#define PRG_ETH0_ADJ_DELAY		GENMASK(19, 15)
+/* Adjusts the skew between each bit of RXEN and RXD[3:0]. If a signal has a
+ * large input delay, the bit for that signal (RXEN = bit 0, RXD[3] = bit 1,
+ * ...) can be configured to be 1 to compensate for a delay of about 1ns.
+ */
+#define PRG_ETH0_ADJ_SKEW		GENMASK(24, 20)
+
+struct meson8b_dwmac;
+
+struct meson8b_dwmac_data {
+	int (*set_phy_mode)(struct meson8b_dwmac *dwmac);
+};
+
+struct meson8b_dwmac {
+	struct device			*dev;
+	void __iomem			*regs;
+
+	const struct meson8b_dwmac_data	*data;
+	phy_interface_t			phy_mode;
+	struct clk			*rgmii_tx_clk;
+	u32				tx_delay_ns;
+	u32				rx_delay_ns;
+	struct clk			*timing_adj_clk;
+};
+
+struct meson8b_dwmac_clk_configs {
+	struct clk_mux		m250_mux;
+	struct clk_divider	m250_div;
+	struct clk_fixed_factor	fixed_div2;
+	struct clk_gate		rgmii_tx_en;
+};
+
+static void meson8b_dwmac_mask_bits(struct meson8b_dwmac *dwmac, u32 reg,
+				    u32 mask, u32 value)
+{
+	u32 data;
+
+	data = readl(dwmac->regs + reg);
+	data &= ~mask;
+	data |= (value & mask);
+
+	writel(data, dwmac->regs + reg);
+}
+
+static struct clk *meson8b_dwmac_register_clk(struct meson8b_dwmac *dwmac,
+					      const char *name_suffix,
+					      const struct clk_parent_data *parents,
+					      int num_parents,
+					      const struct clk_ops *ops,
+					      struct clk_hw *hw)
+{
+	struct clk_init_data init = { };
+	char clk_name[32];
+
+	snprintf(clk_name, sizeof(clk_name), "%s#%s", dev_name(dwmac->dev),
+		 name_suffix);
+
+	init.name = clk_name;
+	init.ops = ops;
+	init.flags = CLK_SET_RATE_PARENT;
+	init.parent_data = parents;
+	init.num_parents = num_parents;
+
+	hw->init = &init;
+
+	return devm_clk_register(dwmac->dev, hw);
+}
+
+static int meson8b_init_rgmii_tx_clk(struct meson8b_dwmac *dwmac)
+{
+	struct clk *clk;
+	struct device *dev = dwmac->dev;
+	static const struct clk_parent_data mux_parents[] = {
+		{ .fw_name = "clkin0", },
+		{ .index = -1, },
+	};
+	static const struct clk_div_table div_table[] = {
+		{ .div = 2, .val = 2, },
+		{ .div = 3, .val = 3, },
+		{ .div = 4, .val = 4, },
+		{ .div = 5, .val = 5, },
+		{ .div = 6, .val = 6, },
+		{ .div = 7, .val = 7, },
+		{ /* end of array */ }
+	};
+	struct meson8b_dwmac_clk_configs *clk_configs;
+	struct clk_parent_data parent_data = { };
+
+	clk_configs = devm_kzalloc(dev, sizeof(*clk_configs), GFP_KERNEL);
+	if (!clk_configs)
+		return -ENOMEM;
+
+	clk_configs->m250_mux.reg = dwmac->regs + PRG_ETH0;
+	clk_configs->m250_mux.shift = __ffs(PRG_ETH0_CLK_M250_SEL_MASK);
+	clk_configs->m250_mux.mask = PRG_ETH0_CLK_M250_SEL_MASK >>
+				     clk_configs->m250_mux.shift;
+	clk = meson8b_dwmac_register_clk(dwmac, "m250_sel", mux_parents,
+					 ARRAY_SIZE(mux_parents), &clk_mux_ops,
+					 &clk_configs->m250_mux.hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	parent_data.hw = &clk_configs->m250_mux.hw;
+	clk_configs->m250_div.reg = dwmac->regs + PRG_ETH0;
+	clk_configs->m250_div.shift = PRG_ETH0_CLK_M250_DIV_SHIFT;
+	clk_configs->m250_div.width = PRG_ETH0_CLK_M250_DIV_WIDTH;
+	clk_configs->m250_div.table = div_table;
+	clk_configs->m250_div.flags = CLK_DIVIDER_ALLOW_ZERO |
+				      CLK_DIVIDER_ROUND_CLOSEST;
+	clk = meson8b_dwmac_register_clk(dwmac, "m250_div", &parent_data, 1,
+					 &clk_divider_ops,
+					 &clk_configs->m250_div.hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	parent_data.hw = &clk_configs->m250_div.hw;
+	clk_configs->fixed_div2.mult = 1;
+	clk_configs->fixed_div2.div = 2;
+	clk = meson8b_dwmac_register_clk(dwmac, "fixed_div2", &parent_data, 1,
+					 &clk_fixed_factor_ops,
+					 &clk_configs->fixed_div2.hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	parent_data.hw = &clk_configs->fixed_div2.hw;
+	clk_configs->rgmii_tx_en.reg = dwmac->regs + PRG_ETH0;
+	clk_configs->rgmii_tx_en.bit_idx = PRG_ETH0_RGMII_TX_CLK_EN;
+	clk = meson8b_dwmac_register_clk(dwmac, "rgmii_tx_en", &parent_data, 1,
+					 &clk_gate_ops,
+					 &clk_configs->rgmii_tx_en.hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	dwmac->rgmii_tx_clk = clk;
+
+	return 0;
+}
+
+static int meson8b_set_phy_mode(struct meson8b_dwmac *dwmac)
+{
+	switch (dwmac->phy_mode) {
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		/* enable RGMII mode */
+		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+					PRG_ETH0_RGMII_MODE,
+					PRG_ETH0_RGMII_MODE);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		/* disable RGMII mode -> enables RMII mode */
+		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+					PRG_ETH0_RGMII_MODE, 0);
+		break;
+	default:
+		dev_err(dwmac->dev, "fail to set phy-mode %s\n",
+			phy_modes(dwmac->phy_mode));
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int meson_axg_set_phy_mode(struct meson8b_dwmac *dwmac)
+{
+	switch (dwmac->phy_mode) {
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		/* enable RGMII mode */
+		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+					PRG_ETH0_EXT_PHY_MODE_MASK,
+					PRG_ETH0_EXT_RGMII_MODE);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		/* disable RGMII mode -> enables RMII mode */
+		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+					PRG_ETH0_EXT_PHY_MODE_MASK,
+					PRG_ETH0_EXT_RMII_MODE);
+		break;
+	default:
+		dev_err(dwmac->dev, "fail to set phy-mode %s\n",
+			phy_modes(dwmac->phy_mode));
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int meson8b_devm_clk_prepare_enable(struct meson8b_dwmac *dwmac,
+					   struct clk *clk)
+{
+	int ret;
+
+	ret = clk_prepare_enable(clk);
+	if (ret)
+		return ret;
+
+	return devm_add_action_or_reset(dwmac->dev,
+					(void(*)(void *))clk_disable_unprepare,
+					clk);
+}
+
+static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
+{
+	u32 tx_dly_config, rx_dly_config, delay_config;
+	int ret;
+
+	tx_dly_config = FIELD_PREP(PRG_ETH0_TXDLY_MASK,
+				   dwmac->tx_delay_ns >> 1);
+
+	if (dwmac->rx_delay_ns == 2)
+		rx_dly_config = PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;
+	else
+		rx_dly_config = 0;
+
+	switch (dwmac->phy_mode) {
+	case PHY_INTERFACE_MODE_RGMII:
+		delay_config = tx_dly_config | rx_dly_config;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		delay_config = tx_dly_config;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		delay_config = rx_dly_config;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RMII:
+		delay_config = 0;
+		break;
+	default:
+		dev_err(dwmac->dev, "unsupported phy-mode %s\n",
+			phy_modes(dwmac->phy_mode));
+		return -EINVAL;
+	};
+
+	if (delay_config & PRG_ETH0_ADJ_ENABLE) {
+		if (!dwmac->timing_adj_clk) {
+			dev_err(dwmac->dev,
+				"The timing-adjustment clock is mandatory for the RX delay re-timing\n");
+			return -EINVAL;
+		}
+
+		/* The timing adjustment logic is driven by a separate clock */
+		ret = meson8b_devm_clk_prepare_enable(dwmac,
+						      dwmac->timing_adj_clk);
+		if (ret) {
+			dev_err(dwmac->dev,
+				"Failed to enable the timing-adjustment clock\n");
+			return ret;
+		}
+	}
+
+	meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK |
+				PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP |
+				PRG_ETH0_ADJ_DELAY | PRG_ETH0_ADJ_SKEW,
+				delay_config);
+
+	if (phy_interface_mode_is_rgmii(dwmac->phy_mode)) {
+		/* only relevant for RMII mode -> disable in RGMII mode */
+		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+					PRG_ETH0_INVERTED_RMII_CLK, 0);
+
+		/* Configure the 125MHz RGMII TX clock, the IP block changes
+		 * the output automatically (= without us having to configure
+		 * a register) based on the line-speed (125MHz for Gbit speeds,
+		 * 25MHz for 100Mbit/s and 2.5MHz for 10Mbit/s).
+		 */
+		ret = clk_set_rate(dwmac->rgmii_tx_clk, 125 * 1000 * 1000);
+		if (ret) {
+			dev_err(dwmac->dev,
+				"failed to set RGMII TX clock\n");
+			return ret;
+		}
+
+		ret = meson8b_devm_clk_prepare_enable(dwmac,
+						      dwmac->rgmii_tx_clk);
+		if (ret) {
+			dev_err(dwmac->dev,
+				"failed to enable the RGMII TX clock\n");
+			return ret;
+		}
+	} else {
+		/* invert internal clk_rmii_i to generate 25/2.5 tx_rx_clk */
+		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
+					PRG_ETH0_INVERTED_RMII_CLK,
+					PRG_ETH0_INVERTED_RMII_CLK);
+	}
+
+	/* enable TX_CLK and PHY_REF_CLK generator */
+	meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TX_AND_PHY_REF_CLK,
+				PRG_ETH0_TX_AND_PHY_REF_CLK);
+
+	return 0;
+}
+
+static int meson8b_dwmac_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacenet_data *plat_dat;
+	struct stmmac_resources stmmac_res;
+	struct meson8b_dwmac *dwmac;
+	int ret;
+
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return ret;
+
+	plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
+	if (IS_ERR(plat_dat))
+		return PTR_ERR(plat_dat);
+
+	dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+	if (!dwmac) {
+		ret = -ENOMEM;
+		goto err_remove_config_dt;
+	}
+
+	dwmac->data = (const struct meson8b_dwmac_data *)
+		of_device_get_match_data(&pdev->dev);
+	if (!dwmac->data) {
+		ret = -EINVAL;
+		goto err_remove_config_dt;
+	}
+	dwmac->regs = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(dwmac->regs)) {
+		ret = PTR_ERR(dwmac->regs);
+		goto err_remove_config_dt;
+	}
+
+	dwmac->dev = &pdev->dev;
+	ret = of_get_phy_mode(pdev->dev.of_node, &dwmac->phy_mode);
+	if (ret) {
+		dev_err(&pdev->dev, "missing phy-mode property\n");
+		goto err_remove_config_dt;
+	}
+
+	/* use 2ns as fallback since this value was previously hardcoded */
+	if (of_property_read_u32(pdev->dev.of_node, "amlogic,tx-delay-ns",
+				 &dwmac->tx_delay_ns))
+		dwmac->tx_delay_ns = 2;
+
+	/* use 0ns as fallback since this is what most boards actually use */
+	if (of_property_read_u32(pdev->dev.of_node, "amlogic,rx-delay-ns",
+				 &dwmac->rx_delay_ns))
+		dwmac->rx_delay_ns = 0;
+
+	if (dwmac->rx_delay_ns != 0 && dwmac->rx_delay_ns != 2) {
+		dev_err(&pdev->dev,
+			"The only allowed RX delays values are: 0ns, 2ns");
+		ret = -EINVAL;
+		goto err_remove_config_dt;
+	}
+
+	dwmac->timing_adj_clk = devm_clk_get_optional(dwmac->dev,
+						      "timing-adjustment");
+	if (IS_ERR(dwmac->timing_adj_clk)) {
+		ret = PTR_ERR(dwmac->timing_adj_clk);
+		goto err_remove_config_dt;
+	}
+
+	ret = meson8b_init_rgmii_tx_clk(dwmac);
+	if (ret)
+		goto err_remove_config_dt;
+
+	ret = dwmac->data->set_phy_mode(dwmac);
+	if (ret)
+		goto err_remove_config_dt;
+
+	ret = meson8b_init_prg_eth(dwmac);
+	if (ret)
+		goto err_remove_config_dt;
+
+	plat_dat->bsp_priv = dwmac;
+
+	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
+	if (ret)
+		goto err_remove_config_dt;
+
+	return 0;
+
+err_remove_config_dt:
+	stmmac_remove_config_dt(pdev, plat_dat);
+
+	return ret;
+}
+
+static const struct meson8b_dwmac_data meson8b_dwmac_data = {
+	.set_phy_mode = meson8b_set_phy_mode,
+};
+
+static const struct meson8b_dwmac_data meson_axg_dwmac_data = {
+	.set_phy_mode = meson_axg_set_phy_mode,
+};
+
+static const struct of_device_id meson8b_dwmac_match[] = {
+	{
+		.compatible = "amlogic,meson8b-dwmac",
+		.data = &meson8b_dwmac_data,
+	},
+	{
+		.compatible = "amlogic,meson8m2-dwmac",
+		.data = &meson8b_dwmac_data,
+	},
+	{
+		.compatible = "amlogic,meson-gxbb-dwmac",
+		.data = &meson8b_dwmac_data,
+	},
+	{
+		.compatible = "amlogic,meson-axg-dwmac",
+		.data = &meson_axg_dwmac_data,
+	},
+	{
+		.compatible = "amlogic,meson-g12a-dwmac",
+		.data = &meson_axg_dwmac_data,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, meson8b_dwmac_match);
+
+static struct platform_driver meson8b_dwmac_driver = {
+	.probe  = meson8b_dwmac_probe,
+	.remove = stmmac_pltfr_remove,
+	.driver = {
+		.name           = "meson8b-dwmac",
+		.pm		= &stmmac_pltfr_pm_ops,
+		.of_match_table = meson8b_dwmac_match,
+	},
+};
+module_platform_driver(meson8b_dwmac_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
+MODULE_DESCRIPTION("Amlogic Meson8b, Meson8m2 and GXBB DWMAC glue layer");
+MODULE_LICENSE("GPL v2");