Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 942 insertions, 0 deletions

diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
new file mode 100644
index 000000000..48602dba4
--- /dev/null
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c
@@ -0,0 +1,942 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+#include "../core.h"
+#include "../pinctrl-utils.h"
+
+#define PMIC_MPP_ADDRESS_RANGE			0x100
+
+/*
+ * Pull Up Values - it indicates whether a pull-up should be
+ * applied for bidirectional mode only. The hardware ignores the
+ * configuration when operating in other modes.
+ */
+#define PMIC_MPP_PULL_UP_0P6KOHM		0
+#define PMIC_MPP_PULL_UP_10KOHM			1
+#define PMIC_MPP_PULL_UP_30KOHM			2
+#define PMIC_MPP_PULL_UP_OPEN			3
+
+/* type registers base address bases */
+#define PMIC_MPP_REG_TYPE			0x4
+#define PMIC_MPP_REG_SUBTYPE			0x5
+
+/* mpp peripheral type and subtype values */
+#define PMIC_MPP_TYPE				0x11
+#define PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT		0x3
+#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT	0x4
+#define PMIC_MPP_SUBTYPE_4CH_NO_SINK		0x5
+#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK	0x6
+#define PMIC_MPP_SUBTYPE_4CH_FULL_FUNC		0x7
+#define PMIC_MPP_SUBTYPE_8CH_FULL_FUNC		0xf
+
+#define PMIC_MPP_REG_RT_STS			0x10
+#define PMIC_MPP_REG_RT_STS_VAL_MASK		0x1
+
+/* control register base address bases */
+#define PMIC_MPP_REG_MODE_CTL			0x40
+#define PMIC_MPP_REG_DIG_VIN_CTL		0x41
+#define PMIC_MPP_REG_DIG_PULL_CTL		0x42
+#define PMIC_MPP_REG_DIG_IN_CTL			0x43
+#define PMIC_MPP_REG_EN_CTL			0x46
+#define PMIC_MPP_REG_AOUT_CTL			0x48
+#define PMIC_MPP_REG_AIN_CTL			0x4a
+#define PMIC_MPP_REG_SINK_CTL			0x4c
+
+/* PMIC_MPP_REG_MODE_CTL */
+#define PMIC_MPP_REG_MODE_VALUE_MASK		0x1
+#define PMIC_MPP_REG_MODE_FUNCTION_SHIFT	1
+#define PMIC_MPP_REG_MODE_FUNCTION_MASK		0x7
+#define PMIC_MPP_REG_MODE_DIR_SHIFT		4
+#define PMIC_MPP_REG_MODE_DIR_MASK		0x7
+
+/* PMIC_MPP_REG_DIG_VIN_CTL */
+#define PMIC_MPP_REG_VIN_SHIFT			0
+#define PMIC_MPP_REG_VIN_MASK			0x7
+
+/* PMIC_MPP_REG_DIG_PULL_CTL */
+#define PMIC_MPP_REG_PULL_SHIFT			0
+#define PMIC_MPP_REG_PULL_MASK			0x7
+
+/* PMIC_MPP_REG_EN_CTL */
+#define PMIC_MPP_REG_MASTER_EN_SHIFT		7
+
+/* PMIC_MPP_REG_AIN_CTL */
+#define PMIC_MPP_REG_AIN_ROUTE_SHIFT		0
+#define PMIC_MPP_REG_AIN_ROUTE_MASK		0x7
+
+#define PMIC_MPP_MODE_DIGITAL_INPUT		0
+#define PMIC_MPP_MODE_DIGITAL_OUTPUT		1
+#define PMIC_MPP_MODE_DIGITAL_BIDIR		2
+#define PMIC_MPP_MODE_ANALOG_BIDIR		3
+#define PMIC_MPP_MODE_ANALOG_INPUT		4
+#define PMIC_MPP_MODE_ANALOG_OUTPUT		5
+#define PMIC_MPP_MODE_CURRENT_SINK		6
+
+#define PMIC_MPP_SELECTOR_NORMAL		0
+#define PMIC_MPP_SELECTOR_PAIRED		1
+#define PMIC_MPP_SELECTOR_DTEST_FIRST		4
+
+#define PMIC_MPP_PHYSICAL_OFFSET		1
+
+/* Qualcomm specific pin configurations */
+#define PMIC_MPP_CONF_AMUX_ROUTE		(PIN_CONFIG_END + 1)
+#define PMIC_MPP_CONF_ANALOG_LEVEL		(PIN_CONFIG_END + 2)
+#define PMIC_MPP_CONF_DTEST_SELECTOR		(PIN_CONFIG_END + 3)
+#define PMIC_MPP_CONF_PAIRED			(PIN_CONFIG_END + 4)
+
+/**
+ * struct pmic_mpp_pad - keep current MPP settings
+ * @base: Address base in SPMI device.
+ * @irq: IRQ number which this MPP generate.
+ * @is_enabled: Set to false when MPP should be put in high Z state.
+ * @out_value: Cached pin output value.
+ * @output_enabled: Set to true if MPP output logic is enabled.
+ * @input_enabled: Set to true if MPP input buffer logic is enabled.
+ * @paired: Pin operates in paired mode
+ * @has_pullup: Pin has support to configure pullup
+ * @num_sources: Number of power-sources supported by this MPP.
+ * @power_source: Current power-source used.
+ * @amux_input: Set the source for analog input.
+ * @aout_level: Analog output level
+ * @pullup: Pullup resistor value. Valid in Bidirectional mode only.
+ * @function: See pmic_mpp_functions[].
+ * @drive_strength: Amount of current in sink mode
+ * @dtest: DTEST route selector
+ */
+struct pmic_mpp_pad {
+	u16		base;
+	int		irq;
+	bool		is_enabled;
+	bool		out_value;
+	bool		output_enabled;
+	bool		input_enabled;
+	bool		paired;
+	bool		has_pullup;
+	unsigned int	num_sources;
+	unsigned int	power_source;
+	unsigned int	amux_input;
+	unsigned int	aout_level;
+	unsigned int	pullup;
+	unsigned int	function;
+	unsigned int	drive_strength;
+	unsigned int	dtest;
+};
+
+struct pmic_mpp_state {
+	struct device	*dev;
+	struct regmap	*map;
+	struct pinctrl_dev *ctrl;
+	struct gpio_chip chip;
+};
+
+static const struct pinconf_generic_params pmic_mpp_bindings[] = {
+	{"qcom,amux-route",	PMIC_MPP_CONF_AMUX_ROUTE,	0},
+	{"qcom,analog-level",	PMIC_MPP_CONF_ANALOG_LEVEL,	0},
+	{"qcom,dtest",		PMIC_MPP_CONF_DTEST_SELECTOR,	0},
+	{"qcom,paired",		PMIC_MPP_CONF_PAIRED,		0},
+};
+
+#ifdef CONFIG_DEBUG_FS
+static const struct pin_config_item pmic_conf_items[] = {
+	PCONFDUMP(PMIC_MPP_CONF_AMUX_ROUTE, "analog mux", NULL, true),
+	PCONFDUMP(PMIC_MPP_CONF_ANALOG_LEVEL, "analog level", NULL, true),
+	PCONFDUMP(PMIC_MPP_CONF_DTEST_SELECTOR, "dtest", NULL, true),
+	PCONFDUMP(PMIC_MPP_CONF_PAIRED, "paired", NULL, false),
+};
+#endif
+
+static const char *const pmic_mpp_groups[] = {
+	"mpp1", "mpp2", "mpp3", "mpp4", "mpp5", "mpp6", "mpp7", "mpp8",
+};
+
+#define PMIC_MPP_DIGITAL	0
+#define PMIC_MPP_ANALOG		1
+#define PMIC_MPP_SINK		2
+
+static const char *const pmic_mpp_functions[] = {
+	"digital", "analog", "sink"
+};
+
+static int pmic_mpp_read(struct pmic_mpp_state *state,
+			 struct pmic_mpp_pad *pad, unsigned int addr)
+{
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(state->map, pad->base + addr, &val);
+	if (ret < 0)
+		dev_err(state->dev, "read 0x%x failed\n", addr);
+	else
+		ret = val;
+
+	return ret;
+}
+
+static int pmic_mpp_write(struct pmic_mpp_state *state,
+			  struct pmic_mpp_pad *pad, unsigned int addr,
+			  unsigned int val)
+{
+	int ret;
+
+	ret = regmap_write(state->map, pad->base + addr, val);
+	if (ret < 0)
+		dev_err(state->dev, "write 0x%x failed\n", addr);
+
+	return ret;
+}
+
+static int pmic_mpp_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	/* Every PIN is a group */
+	return pctldev->desc->npins;
+}
+
+static const char *pmic_mpp_get_group_name(struct pinctrl_dev *pctldev,
+					   unsigned pin)
+{
+	return pctldev->desc->pins[pin].name;
+}
+
+static int pmic_mpp_get_group_pins(struct pinctrl_dev *pctldev,
+				   unsigned pin,
+				   const unsigned **pins, unsigned *num_pins)
+{
+	*pins = &pctldev->desc->pins[pin].number;
+	*num_pins = 1;
+	return 0;
+}
+
+static const struct pinctrl_ops pmic_mpp_pinctrl_ops = {
+	.get_groups_count	= pmic_mpp_get_groups_count,
+	.get_group_name		= pmic_mpp_get_group_name,
+	.get_group_pins		= pmic_mpp_get_group_pins,
+	.dt_node_to_map		= pinconf_generic_dt_node_to_map_group,
+	.dt_free_map		= pinctrl_utils_free_map,
+};
+
+static int pmic_mpp_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(pmic_mpp_functions);
+}
+
+static const char *pmic_mpp_get_function_name(struct pinctrl_dev *pctldev,
+					      unsigned function)
+{
+	return pmic_mpp_functions[function];
+}
+
+static int pmic_mpp_get_function_groups(struct pinctrl_dev *pctldev,
+					unsigned function,
+					const char *const **groups,
+					unsigned *const num_qgroups)
+{
+	*groups = pmic_mpp_groups;
+	*num_qgroups = pctldev->desc->npins;
+	return 0;
+}
+
+static int pmic_mpp_write_mode_ctl(struct pmic_mpp_state *state,
+				   struct pmic_mpp_pad *pad)
+{
+	unsigned int mode;
+	unsigned int sel;
+	unsigned int val;
+	unsigned int en;
+
+	switch (pad->function) {
+	case PMIC_MPP_ANALOG:
+		if (pad->input_enabled && pad->output_enabled)
+			mode = PMIC_MPP_MODE_ANALOG_BIDIR;
+		else if (pad->input_enabled)
+			mode = PMIC_MPP_MODE_ANALOG_INPUT;
+		else
+			mode = PMIC_MPP_MODE_ANALOG_OUTPUT;
+		break;
+	case PMIC_MPP_DIGITAL:
+		if (pad->input_enabled && pad->output_enabled)
+			mode = PMIC_MPP_MODE_DIGITAL_BIDIR;
+		else if (pad->input_enabled)
+			mode = PMIC_MPP_MODE_DIGITAL_INPUT;
+		else
+			mode = PMIC_MPP_MODE_DIGITAL_OUTPUT;
+		break;
+	case PMIC_MPP_SINK:
+	default:
+		mode = PMIC_MPP_MODE_CURRENT_SINK;
+		break;
+	}
+
+	if (pad->dtest)
+		sel = PMIC_MPP_SELECTOR_DTEST_FIRST + pad->dtest - 1;
+	else if (pad->paired)
+		sel = PMIC_MPP_SELECTOR_PAIRED;
+	else
+		sel = PMIC_MPP_SELECTOR_NORMAL;
+
+	en = !!pad->out_value;
+
+	val = mode << PMIC_MPP_REG_MODE_DIR_SHIFT |
+	      sel << PMIC_MPP_REG_MODE_FUNCTION_SHIFT |
+	      en;
+
+	return pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val);
+}
+
+static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function,
+				unsigned pin)
+{
+	struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
+	struct pmic_mpp_pad *pad;
+	unsigned int val;
+	int ret;
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	pad->function = function;
+
+	ret = pmic_mpp_write_mode_ctl(state, pad);
+	if (ret < 0)
+		return ret;
+
+	val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
+
+	return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val);
+}
+
+static const struct pinmux_ops pmic_mpp_pinmux_ops = {
+	.get_functions_count	= pmic_mpp_get_functions_count,
+	.get_function_name	= pmic_mpp_get_function_name,
+	.get_function_groups	= pmic_mpp_get_function_groups,
+	.set_mux		= pmic_mpp_set_mux,
+};
+
+static int pmic_mpp_config_get(struct pinctrl_dev *pctldev,
+			       unsigned int pin, unsigned long *config)
+{
+	unsigned param = pinconf_to_config_param(*config);
+	struct pmic_mpp_pad *pad;
+	unsigned arg = 0;
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	switch (param) {
+	case PIN_CONFIG_BIAS_DISABLE:
+		if (pad->pullup != PMIC_MPP_PULL_UP_OPEN)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		switch (pad->pullup) {
+		case PMIC_MPP_PULL_UP_0P6KOHM:
+			arg = 600;
+			break;
+		case PMIC_MPP_PULL_UP_10KOHM:
+			arg = 10000;
+			break;
+		case PMIC_MPP_PULL_UP_30KOHM:
+			arg = 30000;
+			break;
+		default:
+			return -EINVAL;
+		}
+		break;
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		if (pad->is_enabled)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_POWER_SOURCE:
+		arg = pad->power_source;
+		break;
+	case PIN_CONFIG_INPUT_ENABLE:
+		if (!pad->input_enabled)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_OUTPUT:
+		arg = pad->out_value;
+		break;
+	case PMIC_MPP_CONF_DTEST_SELECTOR:
+		arg = pad->dtest;
+		break;
+	case PMIC_MPP_CONF_AMUX_ROUTE:
+		arg = pad->amux_input;
+		break;
+	case PMIC_MPP_CONF_PAIRED:
+		if (!pad->paired)
+			return -EINVAL;
+		arg = 1;
+		break;
+	case PIN_CONFIG_DRIVE_STRENGTH:
+		arg = pad->drive_strength;
+		break;
+	case PMIC_MPP_CONF_ANALOG_LEVEL:
+		arg = pad->aout_level;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* Convert register value to pinconf value */
+	*config = pinconf_to_config_packed(param, arg);
+	return 0;
+}
+
+static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
+			       unsigned long *configs, unsigned nconfs)
+{
+	struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
+	struct pmic_mpp_pad *pad;
+	unsigned param, arg;
+	unsigned int val;
+	int i, ret;
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	/* Make it possible to enable the pin, by not setting high impedance */
+	pad->is_enabled = true;
+
+	for (i = 0; i < nconfs; i++) {
+		param = pinconf_to_config_param(configs[i]);
+		arg = pinconf_to_config_argument(configs[i]);
+
+		switch (param) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			pad->pullup = PMIC_MPP_PULL_UP_OPEN;
+			break;
+		case PIN_CONFIG_BIAS_PULL_UP:
+			switch (arg) {
+			case 600:
+				pad->pullup = PMIC_MPP_PULL_UP_0P6KOHM;
+				break;
+			case 10000:
+				pad->pullup = PMIC_MPP_PULL_UP_10KOHM;
+				break;
+			case 30000:
+				pad->pullup = PMIC_MPP_PULL_UP_30KOHM;
+				break;
+			default:
+				return -EINVAL;
+			}
+			break;
+		case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+			pad->is_enabled = false;
+			break;
+		case PIN_CONFIG_POWER_SOURCE:
+			if (arg >= pad->num_sources)
+				return -EINVAL;
+			pad->power_source = arg;
+			break;
+		case PIN_CONFIG_INPUT_ENABLE:
+			pad->input_enabled = arg ? true : false;
+			break;
+		case PIN_CONFIG_OUTPUT:
+			pad->output_enabled = true;
+			pad->out_value = arg;
+			break;
+		case PMIC_MPP_CONF_DTEST_SELECTOR:
+			pad->dtest = arg;
+			break;
+		case PIN_CONFIG_DRIVE_STRENGTH:
+			pad->drive_strength = arg;
+			break;
+		case PMIC_MPP_CONF_AMUX_ROUTE:
+			if (arg >= PMIC_MPP_AMUX_ROUTE_ABUS4)
+				return -EINVAL;
+			pad->amux_input = arg;
+			break;
+		case PMIC_MPP_CONF_ANALOG_LEVEL:
+			pad->aout_level = arg;
+			break;
+		case PMIC_MPP_CONF_PAIRED:
+			pad->paired = !!arg;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	val = pad->power_source << PMIC_MPP_REG_VIN_SHIFT;
+
+	ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_VIN_CTL, val);
+	if (ret < 0)
+		return ret;
+
+	if (pad->has_pullup) {
+		val = pad->pullup << PMIC_MPP_REG_PULL_SHIFT;
+
+		ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_PULL_CTL,
+				     val);
+		if (ret < 0)
+			return ret;
+	}
+
+	val = pad->amux_input & PMIC_MPP_REG_AIN_ROUTE_MASK;
+
+	ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AIN_CTL, val);
+	if (ret < 0)
+		return ret;
+
+	ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AOUT_CTL, pad->aout_level);
+	if (ret < 0)
+		return ret;
+
+	ret = pmic_mpp_write_mode_ctl(state, pad);
+	if (ret < 0)
+		return ret;
+
+	ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_SINK_CTL, pad->drive_strength);
+	if (ret < 0)
+		return ret;
+
+	val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT;
+
+	return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val);
+}
+
+static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
+				     struct seq_file *s, unsigned pin)
+{
+	struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev);
+	struct pmic_mpp_pad *pad;
+	int ret;
+
+	static const char *const biases[] = {
+		"0.6kOhm", "10kOhm", "30kOhm", "Disabled"
+	};
+
+	pad = pctldev->desc->pins[pin].drv_data;
+
+	seq_printf(s, " mpp%-2d:", pin + PMIC_MPP_PHYSICAL_OFFSET);
+
+	if (!pad->is_enabled) {
+		seq_puts(s, " ---");
+	} else {
+
+		if (pad->input_enabled) {
+			ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS);
+			if (ret < 0)
+				return;
+
+			ret &= PMIC_MPP_REG_RT_STS_VAL_MASK;
+			pad->out_value = ret;
+		}
+
+		seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
+		seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]);
+		seq_printf(s, " vin-%d", pad->power_source);
+		seq_printf(s, " %d", pad->aout_level);
+		if (pad->has_pullup)
+			seq_printf(s, " %-8s", biases[pad->pullup]);
+		seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
+		if (pad->dtest)
+			seq_printf(s, " dtest%d", pad->dtest);
+		if (pad->paired)
+			seq_puts(s, " paired");
+	}
+}
+
+static const struct pinconf_ops pmic_mpp_pinconf_ops = {
+	.is_generic = true,
+	.pin_config_group_get		= pmic_mpp_config_get,
+	.pin_config_group_set		= pmic_mpp_config_set,
+	.pin_config_group_dbg_show	= pmic_mpp_config_dbg_show,
+};
+
+static int pmic_mpp_direction_input(struct gpio_chip *chip, unsigned pin)
+{
+	struct pmic_mpp_state *state = gpiochip_get_data(chip);
+	unsigned long config;
+
+	config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1);
+
+	return pmic_mpp_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_mpp_direction_output(struct gpio_chip *chip,
+				     unsigned pin, int val)
+{
+	struct pmic_mpp_state *state = gpiochip_get_data(chip);
+	unsigned long config;
+
+	config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val);
+
+	return pmic_mpp_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_mpp_get(struct gpio_chip *chip, unsigned pin)
+{
+	struct pmic_mpp_state *state = gpiochip_get_data(chip);
+	struct pmic_mpp_pad *pad;
+	int ret;
+
+	pad = state->ctrl->desc->pins[pin].drv_data;
+
+	if (pad->input_enabled) {
+		ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS);
+		if (ret < 0)
+			return ret;
+
+		pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK;
+	}
+
+	return !!pad->out_value;
+}
+
+static void pmic_mpp_set(struct gpio_chip *chip, unsigned pin, int value)
+{
+	struct pmic_mpp_state *state = gpiochip_get_data(chip);
+	unsigned long config;
+
+	config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value);
+
+	pmic_mpp_config_set(state->ctrl, pin, &config, 1);
+}
+
+static int pmic_mpp_of_xlate(struct gpio_chip *chip,
+			     const struct of_phandle_args *gpio_desc,
+			     u32 *flags)
+{
+	if (chip->of_gpio_n_cells < 2)
+		return -EINVAL;
+
+	if (flags)
+		*flags = gpio_desc->args[1];
+
+	return gpio_desc->args[0] - PMIC_MPP_PHYSICAL_OFFSET;
+}
+
+static int pmic_mpp_to_irq(struct gpio_chip *chip, unsigned pin)
+{
+	struct pmic_mpp_state *state = gpiochip_get_data(chip);
+	struct pmic_mpp_pad *pad;
+
+	pad = state->ctrl->desc->pins[pin].drv_data;
+
+	return pad->irq;
+}
+
+static void pmic_mpp_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+	struct pmic_mpp_state *state = gpiochip_get_data(chip);
+	unsigned i;
+
+	for (i = 0; i < chip->ngpio; i++) {
+		pmic_mpp_config_dbg_show(state->ctrl, s, i);
+		seq_puts(s, "\n");
+	}
+}
+
+static const struct gpio_chip pmic_mpp_gpio_template = {
+	.direction_input	= pmic_mpp_direction_input,
+	.direction_output	= pmic_mpp_direction_output,
+	.get			= pmic_mpp_get,
+	.set			= pmic_mpp_set,
+	.request		= gpiochip_generic_request,
+	.free			= gpiochip_generic_free,
+	.of_xlate		= pmic_mpp_of_xlate,
+	.to_irq			= pmic_mpp_to_irq,
+	.dbg_show		= pmic_mpp_dbg_show,
+};
+
+static int pmic_mpp_populate(struct pmic_mpp_state *state,
+			     struct pmic_mpp_pad *pad)
+{
+	int type, subtype, val, dir;
+	unsigned int sel;
+
+	type = pmic_mpp_read(state, pad, PMIC_MPP_REG_TYPE);
+	if (type < 0)
+		return type;
+
+	if (type != PMIC_MPP_TYPE) {
+		dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n",
+			type, pad->base);
+		return -ENODEV;
+	}
+
+	subtype = pmic_mpp_read(state, pad, PMIC_MPP_REG_SUBTYPE);
+	if (subtype < 0)
+		return subtype;
+
+	switch (subtype) {
+	case PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT:
+	case PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT:
+	case PMIC_MPP_SUBTYPE_4CH_NO_SINK:
+	case PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK:
+	case PMIC_MPP_SUBTYPE_4CH_FULL_FUNC:
+		pad->num_sources = 4;
+		break;
+	case PMIC_MPP_SUBTYPE_8CH_FULL_FUNC:
+		pad->num_sources = 8;
+		break;
+	default:
+		dev_err(state->dev, "unknown MPP type 0x%x at 0x%x\n",
+			subtype, pad->base);
+		return -ENODEV;
+	}
+
+	val = pmic_mpp_read(state, pad, PMIC_MPP_REG_MODE_CTL);
+	if (val < 0)
+		return val;
+
+	pad->out_value = val & PMIC_MPP_REG_MODE_VALUE_MASK;
+
+	dir = val >> PMIC_MPP_REG_MODE_DIR_SHIFT;
+	dir &= PMIC_MPP_REG_MODE_DIR_MASK;
+
+	switch (dir) {
+	case PMIC_MPP_MODE_DIGITAL_INPUT:
+		pad->input_enabled = true;
+		pad->output_enabled = false;
+		pad->function = PMIC_MPP_DIGITAL;
+		break;
+	case PMIC_MPP_MODE_DIGITAL_OUTPUT:
+		pad->input_enabled = false;
+		pad->output_enabled = true;
+		pad->function = PMIC_MPP_DIGITAL;
+		break;
+	case PMIC_MPP_MODE_DIGITAL_BIDIR:
+		pad->input_enabled = true;
+		pad->output_enabled = true;
+		pad->function = PMIC_MPP_DIGITAL;
+		break;
+	case PMIC_MPP_MODE_ANALOG_BIDIR:
+		pad->input_enabled = true;
+		pad->output_enabled = true;
+		pad->function = PMIC_MPP_ANALOG;
+		break;
+	case PMIC_MPP_MODE_ANALOG_INPUT:
+		pad->input_enabled = true;
+		pad->output_enabled = false;
+		pad->function = PMIC_MPP_ANALOG;
+		break;
+	case PMIC_MPP_MODE_ANALOG_OUTPUT:
+		pad->input_enabled = false;
+		pad->output_enabled = true;
+		pad->function = PMIC_MPP_ANALOG;
+		break;
+	case PMIC_MPP_MODE_CURRENT_SINK:
+		pad->input_enabled = false;
+		pad->output_enabled = true;
+		pad->function = PMIC_MPP_SINK;
+		break;
+	default:
+		dev_err(state->dev, "unknown MPP direction\n");
+		return -ENODEV;
+	}
+
+	sel = val >> PMIC_MPP_REG_MODE_FUNCTION_SHIFT;
+	sel &= PMIC_MPP_REG_MODE_FUNCTION_MASK;
+
+	if (sel >= PMIC_MPP_SELECTOR_DTEST_FIRST)
+		pad->dtest = sel + 1;
+	else if (sel == PMIC_MPP_SELECTOR_PAIRED)
+		pad->paired = true;
+
+	val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_VIN_CTL);
+	if (val < 0)
+		return val;
+
+	pad->power_source = val >> PMIC_MPP_REG_VIN_SHIFT;
+	pad->power_source &= PMIC_MPP_REG_VIN_MASK;
+
+	if (subtype != PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT &&
+	    subtype != PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK) {
+		val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_PULL_CTL);
+		if (val < 0)
+			return val;
+
+		pad->pullup = val >> PMIC_MPP_REG_PULL_SHIFT;
+		pad->pullup &= PMIC_MPP_REG_PULL_MASK;
+		pad->has_pullup = true;
+	}
+
+	val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AIN_CTL);
+	if (val < 0)
+		return val;
+
+	pad->amux_input = val >> PMIC_MPP_REG_AIN_ROUTE_SHIFT;
+	pad->amux_input &= PMIC_MPP_REG_AIN_ROUTE_MASK;
+
+	val = pmic_mpp_read(state, pad, PMIC_MPP_REG_SINK_CTL);
+	if (val < 0)
+		return val;
+
+	pad->drive_strength = val;
+
+	val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AOUT_CTL);
+	if (val < 0)
+		return val;
+
+	pad->aout_level = val;
+
+	val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL);
+	if (val < 0)
+		return val;
+
+	pad->is_enabled = !!val;
+
+	return 0;
+}
+
+static int pmic_mpp_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct pinctrl_pin_desc *pindesc;
+	struct pinctrl_desc *pctrldesc;
+	struct pmic_mpp_pad *pad, *pads;
+	struct pmic_mpp_state *state;
+	int ret, npins, i;
+	u32 reg;
+
+	ret = of_property_read_u32(dev->of_node, "reg", &reg);
+	if (ret < 0) {
+		dev_err(dev, "missing base address");
+		return ret;
+	}
+
+	npins = platform_irq_count(pdev);
+	if (!npins)
+		return -EINVAL;
+	if (npins < 0)
+		return npins;
+
+	BUG_ON(npins > ARRAY_SIZE(pmic_mpp_groups));
+
+	state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
+	if (!state)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, state);
+
+	state->dev = &pdev->dev;
+	state->map = dev_get_regmap(dev->parent, NULL);
+
+	pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL);
+	if (!pindesc)
+		return -ENOMEM;
+
+	pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL);
+	if (!pads)
+		return -ENOMEM;
+
+	pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL);
+	if (!pctrldesc)
+		return -ENOMEM;
+
+	pctrldesc->pctlops = &pmic_mpp_pinctrl_ops;
+	pctrldesc->pmxops = &pmic_mpp_pinmux_ops;
+	pctrldesc->confops = &pmic_mpp_pinconf_ops;
+	pctrldesc->owner = THIS_MODULE;
+	pctrldesc->name = dev_name(dev);
+	pctrldesc->pins = pindesc;
+	pctrldesc->npins = npins;
+
+	pctrldesc->num_custom_params = ARRAY_SIZE(pmic_mpp_bindings);
+	pctrldesc->custom_params = pmic_mpp_bindings;
+#ifdef CONFIG_DEBUG_FS
+	pctrldesc->custom_conf_items = pmic_conf_items;
+#endif
+
+	for (i = 0; i < npins; i++, pindesc++) {
+		pad = &pads[i];
+		pindesc->drv_data = pad;
+		pindesc->number = i;
+		pindesc->name = pmic_mpp_groups[i];
+
+		pad->irq = platform_get_irq(pdev, i);
+		if (pad->irq < 0)
+			return pad->irq;
+
+		pad->base = reg + i * PMIC_MPP_ADDRESS_RANGE;
+
+		ret = pmic_mpp_populate(state, pad);
+		if (ret < 0)
+			return ret;
+	}
+
+	state->chip = pmic_mpp_gpio_template;
+	state->chip.parent = dev;
+	state->chip.base = -1;
+	state->chip.ngpio = npins;
+	state->chip.label = dev_name(dev);
+	state->chip.of_gpio_n_cells = 2;
+	state->chip.can_sleep = false;
+
+	state->ctrl = devm_pinctrl_register(dev, pctrldesc, state);
+	if (IS_ERR(state->ctrl))
+		return PTR_ERR(state->ctrl);
+
+	ret = gpiochip_add_data(&state->chip, state);
+	if (ret) {
+		dev_err(state->dev, "can't add gpio chip\n");
+		return ret;
+	}
+
+	ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, npins);
+	if (ret) {
+		dev_err(dev, "failed to add pin range\n");
+		goto err_range;
+	}
+
+	return 0;
+
+err_range:
+	gpiochip_remove(&state->chip);
+	return ret;
+}
+
+static int pmic_mpp_remove(struct platform_device *pdev)
+{
+	struct pmic_mpp_state *state = platform_get_drvdata(pdev);
+
+	gpiochip_remove(&state->chip);
+	return 0;
+}
+
+static const struct of_device_id pmic_mpp_of_match[] = {
+	{ .compatible = "qcom,pm8841-mpp" },	/* 4 MPP's */
+	{ .compatible = "qcom,pm8916-mpp" },	/* 4 MPP's */
+	{ .compatible = "qcom,pm8941-mpp" },	/* 8 MPP's */
+	{ .compatible = "qcom,pm8950-mpp" },	/* 4 MPP's */
+	{ .compatible = "qcom,pmi8950-mpp" },	/* 4 MPP's */
+	{ .compatible = "qcom,pm8994-mpp" },	/* 8 MPP's */
+	{ .compatible = "qcom,pma8084-mpp" },	/* 8 MPP's */
+	{ .compatible = "qcom,spmi-mpp" },	/* Generic */
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, pmic_mpp_of_match);
+
+static struct platform_driver pmic_mpp_driver = {
+	.driver = {
+		   .name = "qcom-spmi-mpp",
+		   .of_match_table = pmic_mpp_of_match,
+	},
+	.probe	= pmic_mpp_probe,
+	.remove = pmic_mpp_remove,
+};
+
+module_platform_driver(pmic_mpp_driver);
+
+MODULE_AUTHOR("Ivan T. Ivanov <iivanov@mm-sol.com>");
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC MPP pin control driver");
+MODULE_ALIAS("platform:qcom-spmi-mpp");
+MODULE_LICENSE("GPL v2");