Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1352 insertions, 0 deletions

diff --git a/drivers/power/supply/sc27xx_fuel_gauge.c b/drivers/power/supply/sc27xx_fuel_gauge.c
new file mode 100644
index 000000000..3bf4b2639
--- /dev/null
+++ b/drivers/power/supply/sc27xx_fuel_gauge.c
@@ -0,0 +1,1352 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 Spreadtrum Communications Inc.
+
+#include <linux/gpio/consumer.h>
+#include <linux/iio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+/* PMIC global control registers definition */
+#define SC27XX_MODULE_EN0		0xc08
+#define SC27XX_CLK_EN0			0xc18
+#define SC27XX_FGU_EN			BIT(7)
+#define SC27XX_FGU_RTC_EN		BIT(6)
+
+/* FGU registers definition */
+#define SC27XX_FGU_START		0x0
+#define SC27XX_FGU_CONFIG		0x4
+#define SC27XX_FGU_ADC_CONFIG		0x8
+#define SC27XX_FGU_STATUS		0xc
+#define SC27XX_FGU_INT_EN		0x10
+#define SC27XX_FGU_INT_CLR		0x14
+#define SC27XX_FGU_INT_STS		0x1c
+#define SC27XX_FGU_VOLTAGE		0x20
+#define SC27XX_FGU_OCV			0x24
+#define SC27XX_FGU_POCV			0x28
+#define SC27XX_FGU_CURRENT		0x2c
+#define SC27XX_FGU_LOW_OVERLOAD		0x34
+#define SC27XX_FGU_CLBCNT_SETH		0x50
+#define SC27XX_FGU_CLBCNT_SETL		0x54
+#define SC27XX_FGU_CLBCNT_DELTH		0x58
+#define SC27XX_FGU_CLBCNT_DELTL		0x5c
+#define SC27XX_FGU_CLBCNT_VALH		0x68
+#define SC27XX_FGU_CLBCNT_VALL		0x6c
+#define SC27XX_FGU_CLBCNT_QMAXL		0x74
+#define SC27XX_FGU_USER_AREA_SET	0xa0
+#define SC27XX_FGU_USER_AREA_CLEAR	0xa4
+#define SC27XX_FGU_USER_AREA_STATUS	0xa8
+#define SC27XX_FGU_VOLTAGE_BUF		0xd0
+#define SC27XX_FGU_CURRENT_BUF		0xf0
+
+#define SC27XX_WRITE_SELCLB_EN		BIT(0)
+#define SC27XX_FGU_CLBCNT_MASK		GENMASK(15, 0)
+#define SC27XX_FGU_CLBCNT_SHIFT		16
+#define SC27XX_FGU_LOW_OVERLOAD_MASK	GENMASK(12, 0)
+
+#define SC27XX_FGU_INT_MASK		GENMASK(9, 0)
+#define SC27XX_FGU_LOW_OVERLOAD_INT	BIT(0)
+#define SC27XX_FGU_CLBCNT_DELTA_INT	BIT(2)
+
+#define SC27XX_FGU_MODE_AREA_MASK	GENMASK(15, 12)
+#define SC27XX_FGU_CAP_AREA_MASK	GENMASK(11, 0)
+#define SC27XX_FGU_MODE_AREA_SHIFT	12
+
+#define SC27XX_FGU_FIRST_POWERTON	GENMASK(3, 0)
+#define SC27XX_FGU_DEFAULT_CAP		GENMASK(11, 0)
+#define SC27XX_FGU_NORMAIL_POWERTON	0x5
+
+#define SC27XX_FGU_CUR_BASIC_ADC	8192
+#define SC27XX_FGU_SAMPLE_HZ		2
+/* micro Ohms */
+#define SC27XX_FGU_IDEAL_RESISTANCE	20000
+
+/*
+ * struct sc27xx_fgu_data: describe the FGU device
+ * @regmap: regmap for register access
+ * @dev: platform device
+ * @battery: battery power supply
+ * @base: the base offset for the controller
+ * @lock: protect the structure
+ * @gpiod: GPIO for battery detection
+ * @channel: IIO channel to get battery temperature
+ * @charge_chan: IIO channel to get charge voltage
+ * @internal_resist: the battery internal resistance in mOhm
+ * @total_cap: the total capacity of the battery in mAh
+ * @init_cap: the initial capacity of the battery in mAh
+ * @alarm_cap: the alarm capacity
+ * @init_clbcnt: the initial coulomb counter
+ * @max_volt: the maximum constant input voltage in millivolt
+ * @min_volt: the minimum drained battery voltage in microvolt
+ * @boot_volt: the voltage measured during boot in microvolt
+ * @table_len: the capacity table length
+ * @resist_table_len: the resistance table length
+ * @cur_1000ma_adc: ADC value corresponding to 1000 mA
+ * @vol_1000mv_adc: ADC value corresponding to 1000 mV
+ * @calib_resist: the real resistance of coulomb counter chip in uOhm
+ * @cap_table: capacity table with corresponding ocv
+ * @resist_table: resistance percent table with corresponding temperature
+ */
+struct sc27xx_fgu_data {
+	struct regmap *regmap;
+	struct device *dev;
+	struct power_supply *battery;
+	u32 base;
+	struct mutex lock;
+	struct gpio_desc *gpiod;
+	struct iio_channel *channel;
+	struct iio_channel *charge_chan;
+	bool bat_present;
+	int internal_resist;
+	int total_cap;
+	int init_cap;
+	int alarm_cap;
+	int init_clbcnt;
+	int max_volt;
+	int min_volt;
+	int boot_volt;
+	int table_len;
+	int resist_table_len;
+	int cur_1000ma_adc;
+	int vol_1000mv_adc;
+	int calib_resist;
+	struct power_supply_battery_ocv_table *cap_table;
+	struct power_supply_resistance_temp_table *resist_table;
+};
+
+static int sc27xx_fgu_cap_to_clbcnt(struct sc27xx_fgu_data *data, int capacity);
+static void sc27xx_fgu_capacity_calibration(struct sc27xx_fgu_data *data,
+					    int cap, bool int_mode);
+static void sc27xx_fgu_adjust_cap(struct sc27xx_fgu_data *data, int cap);
+static int sc27xx_fgu_get_temp(struct sc27xx_fgu_data *data, int *temp);
+
+static const char * const sc27xx_charger_supply_name[] = {
+	"sc2731_charger",
+	"sc2720_charger",
+	"sc2721_charger",
+	"sc2723_charger",
+};
+
+static int sc27xx_fgu_adc_to_current(struct sc27xx_fgu_data *data, s64 adc)
+{
+	return DIV_S64_ROUND_CLOSEST(adc * 1000, data->cur_1000ma_adc);
+}
+
+static int sc27xx_fgu_adc_to_voltage(struct sc27xx_fgu_data *data, s64 adc)
+{
+	return DIV_S64_ROUND_CLOSEST(adc * 1000, data->vol_1000mv_adc);
+}
+
+static int sc27xx_fgu_voltage_to_adc(struct sc27xx_fgu_data *data, int vol)
+{
+	return DIV_ROUND_CLOSEST(vol * data->vol_1000mv_adc, 1000);
+}
+
+static bool sc27xx_fgu_is_first_poweron(struct sc27xx_fgu_data *data)
+{
+	int ret, status, cap, mode;
+
+	ret = regmap_read(data->regmap,
+			  data->base + SC27XX_FGU_USER_AREA_STATUS, &status);
+	if (ret)
+		return false;
+
+	/*
+	 * We use low 4 bits to save the last battery capacity and high 12 bits
+	 * to save the system boot mode.
+	 */
+	mode = (status & SC27XX_FGU_MODE_AREA_MASK) >> SC27XX_FGU_MODE_AREA_SHIFT;
+	cap = status & SC27XX_FGU_CAP_AREA_MASK;
+
+	/*
+	 * When FGU has been powered down, the user area registers became
+	 * default value (0xffff), which can be used to valid if the system is
+	 * first power on or not.
+	 */
+	if (mode == SC27XX_FGU_FIRST_POWERTON || cap == SC27XX_FGU_DEFAULT_CAP)
+		return true;
+
+	return false;
+}
+
+static int sc27xx_fgu_save_boot_mode(struct sc27xx_fgu_data *data,
+				     int boot_mode)
+{
+	int ret;
+
+	ret = regmap_update_bits(data->regmap,
+				 data->base + SC27XX_FGU_USER_AREA_CLEAR,
+				 SC27XX_FGU_MODE_AREA_MASK,
+				 SC27XX_FGU_MODE_AREA_MASK);
+	if (ret)
+		return ret;
+
+	/*
+	 * Since the user area registers are put on power always-on region,
+	 * then these registers changing time will be a little long. Thus
+	 * here we should delay 200us to wait until values are updated
+	 * successfully according to the datasheet.
+	 */
+	udelay(200);
+
+	ret = regmap_update_bits(data->regmap,
+				 data->base + SC27XX_FGU_USER_AREA_SET,
+				 SC27XX_FGU_MODE_AREA_MASK,
+				 boot_mode << SC27XX_FGU_MODE_AREA_SHIFT);
+	if (ret)
+		return ret;
+
+	/*
+	 * Since the user area registers are put on power always-on region,
+	 * then these registers changing time will be a little long. Thus
+	 * here we should delay 200us to wait until values are updated
+	 * successfully according to the datasheet.
+	 */
+	udelay(200);
+
+	/*
+	 * According to the datasheet, we should set the USER_AREA_CLEAR to 0 to
+	 * make the user area data available, otherwise we can not save the user
+	 * area data.
+	 */
+	return regmap_update_bits(data->regmap,
+				  data->base + SC27XX_FGU_USER_AREA_CLEAR,
+				  SC27XX_FGU_MODE_AREA_MASK, 0);
+}
+
+static int sc27xx_fgu_save_last_cap(struct sc27xx_fgu_data *data, int cap)
+{
+	int ret;
+
+	ret = regmap_update_bits(data->regmap,
+				 data->base + SC27XX_FGU_USER_AREA_CLEAR,
+				 SC27XX_FGU_CAP_AREA_MASK,
+				 SC27XX_FGU_CAP_AREA_MASK);
+	if (ret)
+		return ret;
+
+	/*
+	 * Since the user area registers are put on power always-on region,
+	 * then these registers changing time will be a little long. Thus
+	 * here we should delay 200us to wait until values are updated
+	 * successfully according to the datasheet.
+	 */
+	udelay(200);
+
+	ret = regmap_update_bits(data->regmap,
+				 data->base + SC27XX_FGU_USER_AREA_SET,
+				 SC27XX_FGU_CAP_AREA_MASK, cap);
+	if (ret)
+		return ret;
+
+	/*
+	 * Since the user area registers are put on power always-on region,
+	 * then these registers changing time will be a little long. Thus
+	 * here we should delay 200us to wait until values are updated
+	 * successfully according to the datasheet.
+	 */
+	udelay(200);
+
+	/*
+	 * According to the datasheet, we should set the USER_AREA_CLEAR to 0 to
+	 * make the user area data available, otherwise we can not save the user
+	 * area data.
+	 */
+	return regmap_update_bits(data->regmap,
+				  data->base + SC27XX_FGU_USER_AREA_CLEAR,
+				  SC27XX_FGU_CAP_AREA_MASK, 0);
+}
+
+static int sc27xx_fgu_read_last_cap(struct sc27xx_fgu_data *data, int *cap)
+{
+	int ret, value;
+
+	ret = regmap_read(data->regmap,
+			  data->base + SC27XX_FGU_USER_AREA_STATUS, &value);
+	if (ret)
+		return ret;
+
+	*cap = value & SC27XX_FGU_CAP_AREA_MASK;
+	return 0;
+}
+
+/*
+ * When system boots on, we can not read battery capacity from coulomb
+ * registers, since now the coulomb registers are invalid. So we should
+ * calculate the battery open circuit voltage, and get current battery
+ * capacity according to the capacity table.
+ */
+static int sc27xx_fgu_get_boot_capacity(struct sc27xx_fgu_data *data, int *cap)
+{
+	int volt, cur, oci, ocv, ret;
+	bool is_first_poweron = sc27xx_fgu_is_first_poweron(data);
+
+	/*
+	 * If system is not the first power on, we should use the last saved
+	 * battery capacity as the initial battery capacity. Otherwise we should
+	 * re-calculate the initial battery capacity.
+	 */
+	if (!is_first_poweron) {
+		ret = sc27xx_fgu_read_last_cap(data, cap);
+		if (ret)
+			return ret;
+
+		return sc27xx_fgu_save_boot_mode(data, SC27XX_FGU_NORMAIL_POWERTON);
+	}
+
+	/*
+	 * After system booting on, the SC27XX_FGU_CLBCNT_QMAXL register saved
+	 * the first sampled open circuit current.
+	 */
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_QMAXL,
+			  &cur);
+	if (ret)
+		return ret;
+
+	cur <<= 1;
+	oci = sc27xx_fgu_adc_to_current(data, cur - SC27XX_FGU_CUR_BASIC_ADC);
+
+	/*
+	 * Should get the OCV from SC27XX_FGU_POCV register at the system
+	 * beginning. It is ADC values reading from registers which need to
+	 * convert the corresponding voltage.
+	 */
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_POCV, &volt);
+	if (ret)
+		return ret;
+
+	volt = sc27xx_fgu_adc_to_voltage(data, volt);
+	ocv = volt * 1000 - oci * data->internal_resist;
+	data->boot_volt = ocv;
+
+	/*
+	 * Parse the capacity table to look up the correct capacity percent
+	 * according to current battery's corresponding OCV values.
+	 */
+	*cap = power_supply_ocv2cap_simple(data->cap_table, data->table_len,
+					   ocv);
+
+	ret = sc27xx_fgu_save_last_cap(data, *cap);
+	if (ret)
+		return ret;
+
+	return sc27xx_fgu_save_boot_mode(data, SC27XX_FGU_NORMAIL_POWERTON);
+}
+
+static int sc27xx_fgu_set_clbcnt(struct sc27xx_fgu_data *data, int clbcnt)
+{
+	int ret;
+
+	ret = regmap_update_bits(data->regmap,
+				 data->base + SC27XX_FGU_CLBCNT_SETL,
+				 SC27XX_FGU_CLBCNT_MASK, clbcnt);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(data->regmap,
+				 data->base + SC27XX_FGU_CLBCNT_SETH,
+				 SC27XX_FGU_CLBCNT_MASK,
+				 clbcnt >> SC27XX_FGU_CLBCNT_SHIFT);
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(data->regmap, data->base + SC27XX_FGU_START,
+				 SC27XX_WRITE_SELCLB_EN,
+				 SC27XX_WRITE_SELCLB_EN);
+}
+
+static int sc27xx_fgu_get_clbcnt(struct sc27xx_fgu_data *data, int *clb_cnt)
+{
+	int ccl, cch, ret;
+
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_VALL,
+			  &ccl);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CLBCNT_VALH,
+			  &cch);
+	if (ret)
+		return ret;
+
+	*clb_cnt = ccl & SC27XX_FGU_CLBCNT_MASK;
+	*clb_cnt |= (cch & SC27XX_FGU_CLBCNT_MASK) << SC27XX_FGU_CLBCNT_SHIFT;
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_vol_now(struct sc27xx_fgu_data *data, int *val)
+{
+	int ret;
+	u32 vol;
+
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_VOLTAGE_BUF,
+			  &vol);
+	if (ret)
+		return ret;
+
+	/*
+	 * It is ADC values reading from registers which need to convert to
+	 * corresponding voltage values.
+	 */
+	*val = sc27xx_fgu_adc_to_voltage(data, vol);
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_cur_now(struct sc27xx_fgu_data *data, int *val)
+{
+	int ret;
+	u32 cur;
+
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CURRENT_BUF,
+			  &cur);
+	if (ret)
+		return ret;
+
+	/*
+	 * It is ADC values reading from registers which need to convert to
+	 * corresponding current values.
+	 */
+	*val = sc27xx_fgu_adc_to_current(data, cur - SC27XX_FGU_CUR_BASIC_ADC);
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_capacity(struct sc27xx_fgu_data *data, int *cap)
+{
+	int ret, cur_clbcnt, delta_clbcnt, delta_cap, temp;
+
+	/* Get current coulomb counters firstly */
+	ret = sc27xx_fgu_get_clbcnt(data, &cur_clbcnt);
+	if (ret)
+		return ret;
+
+	delta_clbcnt = cur_clbcnt - data->init_clbcnt;
+
+	/*
+	 * Convert coulomb counter to delta capacity (mAh), and set multiplier
+	 * as 10 to improve the precision.
+	 */
+	temp = DIV_ROUND_CLOSEST(delta_clbcnt * 10, 36 * SC27XX_FGU_SAMPLE_HZ);
+	temp = sc27xx_fgu_adc_to_current(data, temp / 1000);
+
+	/*
+	 * Convert to capacity percent of the battery total capacity,
+	 * and multiplier is 100 too.
+	 */
+	delta_cap = DIV_ROUND_CLOSEST(temp * 100, data->total_cap);
+	*cap = delta_cap + data->init_cap;
+
+	/* Calibrate the battery capacity in a normal range. */
+	sc27xx_fgu_capacity_calibration(data, *cap, false);
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_vbat_vol(struct sc27xx_fgu_data *data, int *val)
+{
+	int ret, vol;
+
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_VOLTAGE, &vol);
+	if (ret)
+		return ret;
+
+	/*
+	 * It is ADC values reading from registers which need to convert to
+	 * corresponding voltage values.
+	 */
+	*val = sc27xx_fgu_adc_to_voltage(data, vol);
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_current(struct sc27xx_fgu_data *data, int *val)
+{
+	int ret, cur;
+
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_CURRENT, &cur);
+	if (ret)
+		return ret;
+
+	/*
+	 * It is ADC values reading from registers which need to convert to
+	 * corresponding current values.
+	 */
+	*val = sc27xx_fgu_adc_to_current(data, cur - SC27XX_FGU_CUR_BASIC_ADC);
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_vbat_ocv(struct sc27xx_fgu_data *data, int *val)
+{
+	int vol, cur, ret, temp, resistance;
+
+	ret = sc27xx_fgu_get_vbat_vol(data, &vol);
+	if (ret)
+		return ret;
+
+	ret = sc27xx_fgu_get_current(data, &cur);
+	if (ret)
+		return ret;
+
+	resistance = data->internal_resist;
+	if (data->resist_table_len > 0) {
+		ret = sc27xx_fgu_get_temp(data, &temp);
+		if (ret)
+			return ret;
+
+		resistance = power_supply_temp2resist_simple(data->resist_table,
+						data->resist_table_len, temp);
+		resistance = data->internal_resist * resistance / 100;
+	}
+
+	/* Return the battery OCV in micro volts. */
+	*val = vol * 1000 - cur * resistance;
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_charge_vol(struct sc27xx_fgu_data *data, int *val)
+{
+	int ret, vol;
+
+	ret = iio_read_channel_processed(data->charge_chan, &vol);
+	if (ret < 0)
+		return ret;
+
+	*val = vol * 1000;
+	return 0;
+}
+
+static int sc27xx_fgu_get_temp(struct sc27xx_fgu_data *data, int *temp)
+{
+	return iio_read_channel_processed(data->channel, temp);
+}
+
+static int sc27xx_fgu_get_health(struct sc27xx_fgu_data *data, int *health)
+{
+	int ret, vol;
+
+	ret = sc27xx_fgu_get_vbat_vol(data, &vol);
+	if (ret)
+		return ret;
+
+	if (vol > data->max_volt)
+		*health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+	else
+		*health = POWER_SUPPLY_HEALTH_GOOD;
+
+	return 0;
+}
+
+static int sc27xx_fgu_get_status(struct sc27xx_fgu_data *data, int *status)
+{
+	union power_supply_propval val;
+	struct power_supply *psy;
+	int i, ret = -EINVAL;
+
+	for (i = 0; i < ARRAY_SIZE(sc27xx_charger_supply_name); i++) {
+		psy = power_supply_get_by_name(sc27xx_charger_supply_name[i]);
+		if (!psy)
+			continue;
+
+		ret = power_supply_get_property(psy, POWER_SUPPLY_PROP_STATUS,
+						&val);
+		power_supply_put(psy);
+		if (ret)
+			return ret;
+
+		*status = val.intval;
+	}
+
+	return ret;
+}
+
+static int sc27xx_fgu_get_property(struct power_supply *psy,
+				   enum power_supply_property psp,
+				   union power_supply_propval *val)
+{
+	struct sc27xx_fgu_data *data = power_supply_get_drvdata(psy);
+	int ret = 0;
+	int value;
+
+	mutex_lock(&data->lock);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = sc27xx_fgu_get_status(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value;
+		break;
+
+	case POWER_SUPPLY_PROP_HEALTH:
+		ret = sc27xx_fgu_get_health(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value;
+		break;
+
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = data->bat_present;
+		break;
+
+	case POWER_SUPPLY_PROP_TEMP:
+		ret = sc27xx_fgu_get_temp(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value;
+		break;
+
+	case POWER_SUPPLY_PROP_TECHNOLOGY:
+		val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
+		break;
+
+	case POWER_SUPPLY_PROP_CAPACITY:
+		ret = sc27xx_fgu_get_capacity(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value;
+		break;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_AVG:
+		ret = sc27xx_fgu_get_vbat_vol(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_OCV:
+		ret = sc27xx_fgu_get_vbat_ocv(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value;
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
+		ret = sc27xx_fgu_get_charge_vol(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value;
+		break;
+
+	case POWER_SUPPLY_PROP_CURRENT_AVG:
+		ret = sc27xx_fgu_get_current(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN:
+		val->intval = data->total_cap * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_CHARGE_NOW:
+		ret = sc27xx_fgu_get_clbcnt(data, &value);
+		if (ret)
+			goto error;
+
+		value = DIV_ROUND_CLOSEST(value * 10,
+					  36 * SC27XX_FGU_SAMPLE_HZ);
+		val->intval = sc27xx_fgu_adc_to_current(data, value);
+
+		break;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		ret = sc27xx_fgu_get_vol_now(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		ret = sc27xx_fgu_get_cur_now(data, &value);
+		if (ret)
+			goto error;
+
+		val->intval = value * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_BOOT:
+		val->intval = data->boot_volt;
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+error:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static int sc27xx_fgu_set_property(struct power_supply *psy,
+				   enum power_supply_property psp,
+				   const union power_supply_propval *val)
+{
+	struct sc27xx_fgu_data *data = power_supply_get_drvdata(psy);
+	int ret;
+
+	mutex_lock(&data->lock);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CAPACITY:
+		ret = sc27xx_fgu_save_last_cap(data, val->intval);
+		if (ret < 0)
+			dev_err(data->dev, "failed to save battery capacity\n");
+		break;
+
+	case POWER_SUPPLY_PROP_CALIBRATE:
+		sc27xx_fgu_adjust_cap(data, val->intval);
+		ret = 0;
+		break;
+
+	case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN:
+		data->total_cap = val->intval / 1000;
+		ret = 0;
+		break;
+
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&data->lock);
+
+	return ret;
+}
+
+static int sc27xx_fgu_property_is_writeable(struct power_supply *psy,
+					    enum power_supply_property psp)
+{
+	return psp == POWER_SUPPLY_PROP_CAPACITY ||
+		psp == POWER_SUPPLY_PROP_CALIBRATE ||
+		psp == POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN;
+}
+
+static enum power_supply_property sc27xx_fgu_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_VOLTAGE_OCV,
+	POWER_SUPPLY_PROP_VOLTAGE_AVG,
+	POWER_SUPPLY_PROP_VOLTAGE_BOOT,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CURRENT_AVG,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
+	POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CALIBRATE,
+	POWER_SUPPLY_PROP_CHARGE_NOW
+};
+
+static const struct power_supply_desc sc27xx_fgu_desc = {
+	.name			= "sc27xx-fgu",
+	.type			= POWER_SUPPLY_TYPE_BATTERY,
+	.properties		= sc27xx_fgu_props,
+	.num_properties		= ARRAY_SIZE(sc27xx_fgu_props),
+	.get_property		= sc27xx_fgu_get_property,
+	.set_property		= sc27xx_fgu_set_property,
+	.external_power_changed	= power_supply_changed,
+	.property_is_writeable	= sc27xx_fgu_property_is_writeable,
+	.no_thermal		= true,
+};
+
+static void sc27xx_fgu_adjust_cap(struct sc27xx_fgu_data *data, int cap)
+{
+	int ret;
+
+	data->init_cap = cap;
+	ret = sc27xx_fgu_get_clbcnt(data, &data->init_clbcnt);
+	if (ret)
+		dev_err(data->dev, "failed to get init coulomb counter\n");
+}
+
+static void sc27xx_fgu_capacity_calibration(struct sc27xx_fgu_data *data,
+					    int cap, bool int_mode)
+{
+	int ret, ocv, chg_sts, adc;
+
+	ret = sc27xx_fgu_get_vbat_ocv(data, &ocv);
+	if (ret) {
+		dev_err(data->dev, "get battery ocv error.\n");
+		return;
+	}
+
+	ret = sc27xx_fgu_get_status(data, &chg_sts);
+	if (ret) {
+		dev_err(data->dev, "get charger status error.\n");
+		return;
+	}
+
+	/*
+	 * If we are in charging mode, then we do not need to calibrate the
+	 * lower capacity.
+	 */
+	if (chg_sts == POWER_SUPPLY_STATUS_CHARGING)
+		return;
+
+	if ((ocv > data->cap_table[0].ocv && cap < 100) || cap > 100) {
+		/*
+		 * If current OCV value is larger than the max OCV value in
+		 * OCV table, or the current capacity is larger than 100,
+		 * we should force the inititial capacity to 100.
+		 */
+		sc27xx_fgu_adjust_cap(data, 100);
+	} else if (ocv <= data->cap_table[data->table_len - 1].ocv) {
+		/*
+		 * If current OCV value is leass than the minimum OCV value in
+		 * OCV table, we should force the inititial capacity to 0.
+		 */
+		sc27xx_fgu_adjust_cap(data, 0);
+	} else if ((ocv > data->cap_table[data->table_len - 1].ocv && cap <= 0) ||
+		   (ocv > data->min_volt && cap <= data->alarm_cap)) {
+		/*
+		 * If current OCV value is not matchable with current capacity,
+		 * we should re-calculate current capacity by looking up the
+		 * OCV table.
+		 */
+		int cur_cap = power_supply_ocv2cap_simple(data->cap_table,
+							  data->table_len, ocv);
+
+		sc27xx_fgu_adjust_cap(data, cur_cap);
+	} else if (ocv <= data->min_volt) {
+		/*
+		 * If current OCV value is less than the low alarm voltage, but
+		 * current capacity is larger than the alarm capacity, we should
+		 * adjust the inititial capacity to alarm capacity.
+		 */
+		if (cap > data->alarm_cap) {
+			sc27xx_fgu_adjust_cap(data, data->alarm_cap);
+		} else {
+			int cur_cap;
+
+			/*
+			 * If current capacity is equal with 0 or less than 0
+			 * (some error occurs), we should adjust inititial
+			 * capacity to the capacity corresponding to current OCV
+			 * value.
+			 */
+			cur_cap = power_supply_ocv2cap_simple(data->cap_table,
+							      data->table_len,
+							      ocv);
+			sc27xx_fgu_adjust_cap(data, cur_cap);
+		}
+
+		if (!int_mode)
+			return;
+
+		/*
+		 * After adjusting the battery capacity, we should set the
+		 * lowest alarm voltage instead.
+		 */
+		data->min_volt = data->cap_table[data->table_len - 1].ocv;
+		data->alarm_cap = power_supply_ocv2cap_simple(data->cap_table,
+							      data->table_len,
+							      data->min_volt);
+
+		adc = sc27xx_fgu_voltage_to_adc(data, data->min_volt / 1000);
+		regmap_update_bits(data->regmap,
+				   data->base + SC27XX_FGU_LOW_OVERLOAD,
+				   SC27XX_FGU_LOW_OVERLOAD_MASK, adc);
+	}
+}
+
+static irqreturn_t sc27xx_fgu_interrupt(int irq, void *dev_id)
+{
+	struct sc27xx_fgu_data *data = dev_id;
+	int ret, cap;
+	u32 status;
+
+	mutex_lock(&data->lock);
+
+	ret = regmap_read(data->regmap, data->base + SC27XX_FGU_INT_STS,
+			  &status);
+	if (ret)
+		goto out;
+
+	ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_CLR,
+				 status, status);
+	if (ret)
+		goto out;
+
+	/*
+	 * When low overload voltage interrupt happens, we should calibrate the
+	 * battery capacity in lower voltage stage.
+	 */
+	if (!(status & SC27XX_FGU_LOW_OVERLOAD_INT))
+		goto out;
+
+	ret = sc27xx_fgu_get_capacity(data, &cap);
+	if (ret)
+		goto out;
+
+	sc27xx_fgu_capacity_calibration(data, cap, true);
+
+out:
+	mutex_unlock(&data->lock);
+
+	power_supply_changed(data->battery);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t sc27xx_fgu_bat_detection(int irq, void *dev_id)
+{
+	struct sc27xx_fgu_data *data = dev_id;
+	int state;
+
+	mutex_lock(&data->lock);
+
+	state = gpiod_get_value_cansleep(data->gpiod);
+	if (state < 0) {
+		dev_err(data->dev, "failed to get gpio state\n");
+		mutex_unlock(&data->lock);
+		return IRQ_RETVAL(state);
+	}
+
+	data->bat_present = !!state;
+
+	mutex_unlock(&data->lock);
+
+	power_supply_changed(data->battery);
+	return IRQ_HANDLED;
+}
+
+static void sc27xx_fgu_disable(void *_data)
+{
+	struct sc27xx_fgu_data *data = _data;
+
+	regmap_update_bits(data->regmap, SC27XX_CLK_EN0, SC27XX_FGU_RTC_EN, 0);
+	regmap_update_bits(data->regmap, SC27XX_MODULE_EN0, SC27XX_FGU_EN, 0);
+}
+
+static int sc27xx_fgu_cap_to_clbcnt(struct sc27xx_fgu_data *data, int capacity)
+{
+	/*
+	 * Get current capacity (mAh) = battery total capacity (mAh) *
+	 * current capacity percent (capacity / 100).
+	 */
+	int cur_cap = DIV_ROUND_CLOSEST(data->total_cap * capacity, 100);
+
+	/*
+	 * Convert current capacity (mAh) to coulomb counter according to the
+	 * formula: 1 mAh =3.6 coulomb.
+	 */
+	return DIV_ROUND_CLOSEST(cur_cap * 36 * data->cur_1000ma_adc * SC27XX_FGU_SAMPLE_HZ, 10);
+}
+
+static int sc27xx_fgu_calibration(struct sc27xx_fgu_data *data)
+{
+	struct nvmem_cell *cell;
+	int calib_data, cal_4200mv;
+	void *buf;
+	size_t len;
+
+	cell = nvmem_cell_get(data->dev, "fgu_calib");
+	if (IS_ERR(cell))
+		return PTR_ERR(cell);
+
+	buf = nvmem_cell_read(cell, &len);
+	nvmem_cell_put(cell);
+
+	if (IS_ERR(buf))
+		return PTR_ERR(buf);
+
+	memcpy(&calib_data, buf, min(len, sizeof(u32)));
+
+	/*
+	 * Get the ADC value corresponding to 4200 mV from eFuse controller
+	 * according to below formula. Then convert to ADC values corresponding
+	 * to 1000 mV and 1000 mA.
+	 */
+	cal_4200mv = (calib_data & 0x1ff) + 6963 - 4096 - 256;
+	data->vol_1000mv_adc = DIV_ROUND_CLOSEST(cal_4200mv * 10, 42);
+	data->cur_1000ma_adc =
+		DIV_ROUND_CLOSEST(data->vol_1000mv_adc * 4 * data->calib_resist,
+				  SC27XX_FGU_IDEAL_RESISTANCE);
+
+	kfree(buf);
+	return 0;
+}
+
+static int sc27xx_fgu_hw_init(struct sc27xx_fgu_data *data)
+{
+	struct power_supply_battery_info info = { };
+	struct power_supply_battery_ocv_table *table;
+	int ret, delta_clbcnt, alarm_adc;
+
+	ret = power_supply_get_battery_info(data->battery, &info);
+	if (ret) {
+		dev_err(data->dev, "failed to get battery information\n");
+		return ret;
+	}
+
+	data->total_cap = info.charge_full_design_uah / 1000;
+	data->max_volt = info.constant_charge_voltage_max_uv / 1000;
+	data->internal_resist = info.factory_internal_resistance_uohm / 1000;
+	data->min_volt = info.voltage_min_design_uv;
+
+	/*
+	 * For SC27XX fuel gauge device, we only use one ocv-capacity
+	 * table in normal temperature 20 Celsius.
+	 */
+	table = power_supply_find_ocv2cap_table(&info, 20, &data->table_len);
+	if (!table)
+		return -EINVAL;
+
+	data->cap_table = devm_kmemdup(data->dev, table,
+				       data->table_len * sizeof(*table),
+				       GFP_KERNEL);
+	if (!data->cap_table) {
+		power_supply_put_battery_info(data->battery, &info);
+		return -ENOMEM;
+	}
+
+	data->alarm_cap = power_supply_ocv2cap_simple(data->cap_table,
+						      data->table_len,
+						      data->min_volt);
+	if (!data->alarm_cap)
+		data->alarm_cap += 1;
+
+	data->resist_table_len = info.resist_table_size;
+	if (data->resist_table_len > 0) {
+		data->resist_table = devm_kmemdup(data->dev, info.resist_table,
+						  data->resist_table_len *
+						  sizeof(struct power_supply_resistance_temp_table),
+						  GFP_KERNEL);
+		if (!data->resist_table) {
+			power_supply_put_battery_info(data->battery, &info);
+			return -ENOMEM;
+		}
+	}
+
+	power_supply_put_battery_info(data->battery, &info);
+
+	ret = sc27xx_fgu_calibration(data);
+	if (ret)
+		return ret;
+
+	/* Enable the FGU module */
+	ret = regmap_update_bits(data->regmap, SC27XX_MODULE_EN0,
+				 SC27XX_FGU_EN, SC27XX_FGU_EN);
+	if (ret) {
+		dev_err(data->dev, "failed to enable fgu\n");
+		return ret;
+	}
+
+	/* Enable the FGU RTC clock to make it work */
+	ret = regmap_update_bits(data->regmap, SC27XX_CLK_EN0,
+				 SC27XX_FGU_RTC_EN, SC27XX_FGU_RTC_EN);
+	if (ret) {
+		dev_err(data->dev, "failed to enable fgu RTC clock\n");
+		goto disable_fgu;
+	}
+
+	ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_CLR,
+				 SC27XX_FGU_INT_MASK, SC27XX_FGU_INT_MASK);
+	if (ret) {
+		dev_err(data->dev, "failed to clear interrupt status\n");
+		goto disable_clk;
+	}
+
+	/*
+	 * Set the voltage low overload threshold, which means when the battery
+	 * voltage is lower than this threshold, the controller will generate
+	 * one interrupt to notify.
+	 */
+	alarm_adc = sc27xx_fgu_voltage_to_adc(data, data->min_volt / 1000);
+	ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_LOW_OVERLOAD,
+				 SC27XX_FGU_LOW_OVERLOAD_MASK, alarm_adc);
+	if (ret) {
+		dev_err(data->dev, "failed to set fgu low overload\n");
+		goto disable_clk;
+	}
+
+	/*
+	 * Set the coulomb counter delta threshold, that means when the coulomb
+	 * counter change is multiples of the delta threshold, the controller
+	 * will generate one interrupt to notify the users to update the battery
+	 * capacity. Now we set the delta threshold as a counter value of 1%
+	 * capacity.
+	 */
+	delta_clbcnt = sc27xx_fgu_cap_to_clbcnt(data, 1);
+
+	ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_CLBCNT_DELTL,
+				 SC27XX_FGU_CLBCNT_MASK, delta_clbcnt);
+	if (ret) {
+		dev_err(data->dev, "failed to set low delta coulomb counter\n");
+		goto disable_clk;
+	}
+
+	ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_CLBCNT_DELTH,
+				 SC27XX_FGU_CLBCNT_MASK,
+				 delta_clbcnt >> SC27XX_FGU_CLBCNT_SHIFT);
+	if (ret) {
+		dev_err(data->dev, "failed to set high delta coulomb counter\n");
+		goto disable_clk;
+	}
+
+	/*
+	 * Get the boot battery capacity when system powers on, which is used to
+	 * initialize the coulomb counter. After that, we can read the coulomb
+	 * counter to measure the battery capacity.
+	 */
+	ret = sc27xx_fgu_get_boot_capacity(data, &data->init_cap);
+	if (ret) {
+		dev_err(data->dev, "failed to get boot capacity\n");
+		goto disable_clk;
+	}
+
+	/*
+	 * Convert battery capacity to the corresponding initial coulomb counter
+	 * and set into coulomb counter registers.
+	 */
+	data->init_clbcnt = sc27xx_fgu_cap_to_clbcnt(data, data->init_cap);
+	ret = sc27xx_fgu_set_clbcnt(data, data->init_clbcnt);
+	if (ret) {
+		dev_err(data->dev, "failed to initialize coulomb counter\n");
+		goto disable_clk;
+	}
+
+	return 0;
+
+disable_clk:
+	regmap_update_bits(data->regmap, SC27XX_CLK_EN0, SC27XX_FGU_RTC_EN, 0);
+disable_fgu:
+	regmap_update_bits(data->regmap, SC27XX_MODULE_EN0, SC27XX_FGU_EN, 0);
+
+	return ret;
+}
+
+static int sc27xx_fgu_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct power_supply_config fgu_cfg = { };
+	struct sc27xx_fgu_data *data;
+	int ret, irq;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!data->regmap) {
+		dev_err(dev, "failed to get regmap\n");
+		return -ENODEV;
+	}
+
+	ret = device_property_read_u32(dev, "reg", &data->base);
+	if (ret) {
+		dev_err(dev, "failed to get fgu address\n");
+		return ret;
+	}
+
+	ret = device_property_read_u32(&pdev->dev,
+				       "sprd,calib-resistance-micro-ohms",
+				       &data->calib_resist);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to get fgu calibration resistance\n");
+		return ret;
+	}
+
+	data->channel = devm_iio_channel_get(dev, "bat-temp");
+	if (IS_ERR(data->channel)) {
+		dev_err(dev, "failed to get IIO channel\n");
+		return PTR_ERR(data->channel);
+	}
+
+	data->charge_chan = devm_iio_channel_get(dev, "charge-vol");
+	if (IS_ERR(data->charge_chan)) {
+		dev_err(dev, "failed to get charge IIO channel\n");
+		return PTR_ERR(data->charge_chan);
+	}
+
+	data->gpiod = devm_gpiod_get(dev, "bat-detect", GPIOD_IN);
+	if (IS_ERR(data->gpiod)) {
+		dev_err(dev, "failed to get battery detection GPIO\n");
+		return PTR_ERR(data->gpiod);
+	}
+
+	ret = gpiod_get_value_cansleep(data->gpiod);
+	if (ret < 0) {
+		dev_err(dev, "failed to get gpio state\n");
+		return ret;
+	}
+
+	data->bat_present = !!ret;
+	mutex_init(&data->lock);
+	data->dev = dev;
+	platform_set_drvdata(pdev, data);
+
+	fgu_cfg.drv_data = data;
+	fgu_cfg.of_node = np;
+	data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
+						   &fgu_cfg);
+	if (IS_ERR(data->battery)) {
+		dev_err(dev, "failed to register power supply\n");
+		return PTR_ERR(data->battery);
+	}
+
+	ret = sc27xx_fgu_hw_init(data);
+	if (ret) {
+		dev_err(dev, "failed to initialize fgu hardware\n");
+		return ret;
+	}
+
+	ret = devm_add_action_or_reset(dev, sc27xx_fgu_disable, data);
+	if (ret) {
+		dev_err(dev, "failed to add fgu disable action\n");
+		return ret;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "no irq resource specified\n");
+		return irq;
+	}
+
+	ret = devm_request_threaded_irq(data->dev, irq, NULL,
+					sc27xx_fgu_interrupt,
+					IRQF_NO_SUSPEND | IRQF_ONESHOT,
+					pdev->name, data);
+	if (ret) {
+		dev_err(data->dev, "failed to request fgu IRQ\n");
+		return ret;
+	}
+
+	irq = gpiod_to_irq(data->gpiod);
+	if (irq < 0) {
+		dev_err(dev, "failed to translate GPIO to IRQ\n");
+		return irq;
+	}
+
+	ret = devm_request_threaded_irq(dev, irq, NULL,
+					sc27xx_fgu_bat_detection,
+					IRQF_ONESHOT | IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_FALLING,
+					pdev->name, data);
+	if (ret) {
+		dev_err(dev, "failed to request IRQ\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int sc27xx_fgu_resume(struct device *dev)
+{
+	struct sc27xx_fgu_data *data = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_EN,
+				 SC27XX_FGU_LOW_OVERLOAD_INT |
+				 SC27XX_FGU_CLBCNT_DELTA_INT, 0);
+	if (ret) {
+		dev_err(data->dev, "failed to disable fgu interrupts\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int sc27xx_fgu_suspend(struct device *dev)
+{
+	struct sc27xx_fgu_data *data = dev_get_drvdata(dev);
+	int ret, status, ocv;
+
+	ret = sc27xx_fgu_get_status(data, &status);
+	if (ret)
+		return ret;
+
+	/*
+	 * If we are charging, then no need to enable the FGU interrupts to
+	 * adjust the battery capacity.
+	 */
+	if (status != POWER_SUPPLY_STATUS_NOT_CHARGING &&
+	    status != POWER_SUPPLY_STATUS_DISCHARGING)
+		return 0;
+
+	ret = regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_EN,
+				 SC27XX_FGU_LOW_OVERLOAD_INT,
+				 SC27XX_FGU_LOW_OVERLOAD_INT);
+	if (ret) {
+		dev_err(data->dev, "failed to enable low voltage interrupt\n");
+		return ret;
+	}
+
+	ret = sc27xx_fgu_get_vbat_ocv(data, &ocv);
+	if (ret)
+		goto disable_int;
+
+	/*
+	 * If current OCV is less than the minimum voltage, we should enable the
+	 * coulomb counter threshold interrupt to notify events to adjust the
+	 * battery capacity.
+	 */
+	if (ocv < data->min_volt) {
+		ret = regmap_update_bits(data->regmap,
+					 data->base + SC27XX_FGU_INT_EN,
+					 SC27XX_FGU_CLBCNT_DELTA_INT,
+					 SC27XX_FGU_CLBCNT_DELTA_INT);
+		if (ret) {
+			dev_err(data->dev,
+				"failed to enable coulomb threshold int\n");
+			goto disable_int;
+		}
+	}
+
+	return 0;
+
+disable_int:
+	regmap_update_bits(data->regmap, data->base + SC27XX_FGU_INT_EN,
+			   SC27XX_FGU_LOW_OVERLOAD_INT, 0);
+	return ret;
+}
+#endif
+
+static const struct dev_pm_ops sc27xx_fgu_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(sc27xx_fgu_suspend, sc27xx_fgu_resume)
+};
+
+static const struct of_device_id sc27xx_fgu_of_match[] = {
+	{ .compatible = "sprd,sc2731-fgu", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sc27xx_fgu_of_match);
+
+static struct platform_driver sc27xx_fgu_driver = {
+	.probe = sc27xx_fgu_probe,
+	.driver = {
+		.name = "sc27xx-fgu",
+		.of_match_table = sc27xx_fgu_of_match,
+		.pm = &sc27xx_fgu_pm_ops,
+	}
+};
+
+module_platform_driver(sc27xx_fgu_driver);
+
+MODULE_DESCRIPTION("Spreadtrum SC27XX PMICs Fual Gauge Unit Driver");
+MODULE_LICENSE("GPL v2");