Adding upstream version 5.10.209.upstream/5.10.209upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 2240 insertions, 0 deletions

diff --git a/drivers/video/fbdev/Kconfig b/drivers/video/fbdev/Kconfig
new file mode 100644
index 000000000..dd5958463
--- /dev/null
+++ b/drivers/video/fbdev/Kconfig
@@ -0,0 +1,2240 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# fbdev configuration
+#
+
+config FB_CMDLINE
+	bool
+
+config FB_NOTIFY
+	bool
+
+menuconfig FB
+	tristate "Support for frame buffer devices"
+	select FB_CMDLINE
+	select FB_NOTIFY
+	help
+	  The frame buffer device provides an abstraction for the graphics
+	  hardware. It represents the frame buffer of some video hardware and
+	  allows application software to access the graphics hardware through
+	  a well-defined interface, so the software doesn't need to know
+	  anything about the low-level (hardware register) stuff.
+
+	  Frame buffer devices work identically across the different
+	  architectures supported by Linux and make the implementation of
+	  application programs easier and more portable; at this point, an X
+	  server exists which uses the frame buffer device exclusively.
+	  On several non-X86 architectures, the frame buffer device is the
+	  only way to use the graphics hardware.
+
+	  The device is accessed through special device nodes, usually located
+	  in the /dev directory, i.e. /dev/fb*.
+
+	  You need an utility program called fbset to make full use of frame
+	  buffer devices. Please read <file:Documentation/fb/framebuffer.rst>
+	  and the Framebuffer-HOWTO at
+	  <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.3.html> for more
+	  information.
+
+	  Say Y here and to the driver for your graphics board below if you
+	  are compiling a kernel for a non-x86 architecture.
+
+	  If you are compiling for the x86 architecture, you can say Y if you
+	  want to play with it, but it is not essential. Please note that
+	  running graphical applications that directly touch the hardware
+	  (e.g. an accelerated X server) and that are not frame buffer
+	  device-aware may cause unexpected results. If unsure, say N.
+
+config FIRMWARE_EDID
+	bool "Enable firmware EDID"
+	depends on FB
+	help
+	  This enables access to the EDID transferred from the firmware.
+	  On the i386, this is from the Video BIOS. Enable this if DDC/I2C
+	  transfers do not work for your driver and if you are using
+	  nvidiafb, i810fb or savagefb.
+
+	  In general, choosing Y for this option is safe.  If you
+	  experience extremely long delays while booting before you get
+	  something on your display, try setting this to N.  Matrox cards in
+	  combination with certain motherboards and monitors are known to
+	  suffer from this problem.
+
+config FB_DDC
+	tristate
+	depends on FB
+	select I2C_ALGOBIT
+	select I2C
+
+config FB_BOOT_VESA_SUPPORT
+	bool
+	depends on FB
+	help
+	  If true, at least one selected framebuffer driver can take advantage
+	  of VESA video modes set at an early boot stage via the vga= parameter.
+
+config FB_CFB_FILLRECT
+	tristate
+	depends on FB
+	help
+	  Include the cfb_fillrect function for generic software rectangle
+	  filling. This is used by drivers that don't provide their own
+	  (accelerated) version.
+
+config FB_CFB_COPYAREA
+	tristate
+	depends on FB
+	help
+	  Include the cfb_copyarea function for generic software area copying.
+	  This is used by drivers that don't provide their own (accelerated)
+	  version.
+
+config FB_CFB_IMAGEBLIT
+	tristate
+	depends on FB
+	help
+	  Include the cfb_imageblit function for generic software image
+	  blitting. This is used by drivers that don't provide their own
+	  (accelerated) version.
+
+config FB_CFB_REV_PIXELS_IN_BYTE
+	bool
+	depends on FB
+	help
+	  Allow generic frame-buffer functions to work on displays with 1, 2
+	  and 4 bits per pixel depths which has opposite order of pixels in
+	  byte order to bytes in long order.
+
+config FB_SYS_FILLRECT
+	tristate
+	depends on FB
+	help
+	  Include the sys_fillrect function for generic software rectangle
+	  filling. This is used by drivers that don't provide their own
+	  (accelerated) version and the framebuffer is in system RAM.
+
+config FB_SYS_COPYAREA
+	tristate
+	depends on FB
+	help
+	  Include the sys_copyarea function for generic software area copying.
+	  This is used by drivers that don't provide their own (accelerated)
+	  version and the framebuffer is in system RAM.
+
+config FB_SYS_IMAGEBLIT
+	tristate
+	depends on FB
+	help
+	  Include the sys_imageblit function for generic software image
+	  blitting. This is used by drivers that don't provide their own
+	  (accelerated) version and the framebuffer is in system RAM.
+
+config FB_PROVIDE_GET_FB_UNMAPPED_AREA
+	bool
+	depends on FB
+	help
+	  Allow generic frame-buffer to provide get_fb_unmapped_area
+	  function.
+
+menuconfig FB_FOREIGN_ENDIAN
+	bool "Framebuffer foreign endianness support"
+	depends on FB
+	help
+	  This menu will let you enable support for the framebuffers with
+	  non-native endianness (e.g. Little-Endian framebuffer on a
+	  Big-Endian machine). Most probably you don't have such hardware,
+	  so it's safe to say "n" here.
+
+choice
+	prompt "Choice endianness support"
+	depends on FB_FOREIGN_ENDIAN
+
+config FB_BOTH_ENDIAN
+	bool "Support for Big- and Little-Endian framebuffers"
+
+config FB_BIG_ENDIAN
+	bool "Support for Big-Endian framebuffers only"
+
+config FB_LITTLE_ENDIAN
+	bool "Support for Little-Endian framebuffers only"
+
+endchoice
+
+config FB_SYS_FOPS
+	tristate
+	depends on FB
+
+config FB_DEFERRED_IO
+	bool
+	depends on FB
+
+config FB_HECUBA
+	tristate
+	depends on FB
+	depends on FB_DEFERRED_IO
+
+config FB_SVGALIB
+	tristate
+	depends on FB
+	help
+	  Common utility functions useful to fbdev drivers of VGA-based
+	  cards.
+
+config FB_MACMODES
+	tristate
+	depends on FB
+
+config FB_BACKLIGHT
+	tristate
+	depends on FB
+	select BACKLIGHT_CLASS_DEVICE
+
+config FB_MODE_HELPERS
+	bool "Enable Video Mode Handling Helpers"
+	depends on FB
+	help
+	  This enables functions for handling video modes using the
+	  Generalized Timing Formula and the EDID parser. A few drivers rely
+	  on this feature such as the radeonfb, rivafb, and the i810fb. If
+	  your driver does not take advantage of this feature, choosing Y will
+	  just increase the kernel size by about 5K.
+
+config FB_TILEBLITTING
+	bool "Enable Tile Blitting Support"
+	depends on FB
+	help
+	  This enables tile blitting.  Tile blitting is a drawing technique
+	  where the screen is divided into rectangular sections (tiles), whereas
+	  the standard blitting divides the screen into pixels. Because the
+	  default drawing element is a tile, drawing functions will be passed
+	  parameters in terms of number of tiles instead of number of pixels.
+	  For example, to draw a single character, instead of using bitmaps,
+	  an index to an array of bitmaps will be used.  To clear or move a
+	  rectangular section of a screen, the rectangle will be described in
+	  terms of number of tiles in the x- and y-axis.
+
+	  This is particularly important to one driver, matroxfb.  If
+	  unsure, say N.
+
+comment "Frame buffer hardware drivers"
+	depends on FB
+
+config FB_GRVGA
+	tristate "Aeroflex Gaisler framebuffer support"
+	depends on FB && SPARC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This enables support for the SVGACTRL framebuffer in the GRLIB IP library from Aeroflex Gaisler.
+
+config FB_CIRRUS
+	tristate "Cirrus Logic support"
+	depends on FB && (ZORRO || PCI)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This enables support for Cirrus Logic GD542x/543x based boards on
+	  Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
+
+	  If you have a PCI-based system, this enables support for these
+	  chips: GD-543x, GD-544x, GD-5480.
+
+	  Please read the file <file:Documentation/fb/cirrusfb.rst>.
+
+	  Say N unless you have such a graphics board or plan to get one
+	  before you next recompile the kernel.
+
+config FB_PM2
+	tristate "Permedia2 support"
+	depends on FB && ((AMIGA && BROKEN) || PCI)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for cards based on
+	  the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
+	  The driver was tested on the following cards:
+		Diamond FireGL 1000 PRO AGP
+		ELSA Gloria Synergy PCI
+		Appian Jeronimo PRO (both heads) PCI
+		3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
+		Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
+		ASK Graphic Blaster Exxtreme AGP
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called pm2fb.
+
+config FB_PM2_FIFO_DISCONNECT
+	bool "enable FIFO disconnect feature"
+	depends on FB_PM2 && PCI
+	help
+	  Support the Permedia2 FIFO disconnect feature.
+
+config FB_ARMCLCD
+	tristate "ARM PrimeCell PL110 support"
+	depends on ARM || ARM64 || COMPILE_TEST
+	depends on FB && ARM_AMBA && HAS_IOMEM
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MODE_HELPERS if OF
+	select VIDEOMODE_HELPERS if OF
+	select BACKLIGHT_CLASS_DEVICE if OF
+	help
+	  This framebuffer device driver is for the ARM PrimeCell PL110
+	  Colour LCD controller.  ARM PrimeCells provide the building
+	  blocks for System on a Chip devices.
+
+	  If you want to compile this as a module (=code which can be
+	  inserted into and removed from the running kernel), say M
+	  here and read <file:Documentation/kbuild/modules.rst>.  The module
+	  will be called amba-clcd.
+
+config FB_ACORN
+	bool "Acorn VIDC support"
+	depends on (FB = y) && ARM && ARCH_ACORN
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the Acorn VIDC graphics
+	  hardware found in Acorn RISC PCs and other ARM-based machines.  If
+	  unsure, say N.
+
+config FB_CLPS711X
+	tristate "CLPS711X LCD support"
+	depends on FB && (ARCH_CLPS711X || COMPILE_TEST)
+	select FB_MODE_HELPERS
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select LCD_CLASS_DEVICE
+	select VIDEOMODE_HELPERS
+	help
+	  Say Y to enable the Framebuffer driver for the Cirrus Logic
+	  CLPS711X CPUs.
+
+config FB_SA1100
+	bool "SA-1100 LCD support"
+	depends on (FB = y) && ARM && ARCH_SA1100
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is a framebuffer device for the SA-1100 LCD Controller.
+	  See <http://www.linux-fbdev.org/> for information on framebuffer
+	  devices.
+
+	  If you plan to use the LCD display with your SA-1100 system, say
+	  Y here.
+
+config FB_IMX
+	tristate "Freescale i.MX1/21/25/27 LCD support"
+	depends on FB && HAVE_CLK && HAS_IOMEM
+	depends on ARCH_MXC || COMPILE_TEST
+	select LCD_CLASS_DEVICE
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MODE_HELPERS
+	select VIDEOMODE_HELPERS
+
+config FB_CYBER2000
+	tristate "CyberPro 2000/2010/5000 support"
+	depends on FB && PCI && (BROKEN || !SPARC64)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This enables support for the Integraphics CyberPro 20x0 and 5000
+	  VGA chips used in the Rebel.com Netwinder and other machines.
+	  Say Y if you have a NetWinder or a graphics card containing this
+	  device, otherwise say N.
+
+config FB_CYBER2000_DDC
+	bool "DDC for CyberPro support"
+	depends on FB_CYBER2000
+	select FB_DDC
+	default y
+	help
+	  Say Y here if you want DDC support for your CyberPro graphics
+	  card. This is only I2C bus support, driver does not use EDID.
+
+config FB_CYBER2000_I2C
+	bool "CyberPro 2000/2010/5000 I2C support"
+	depends on FB_CYBER2000 && I2C && ARCH_NETWINDER
+	depends on I2C=y || FB_CYBER2000=m
+	select I2C_ALGOBIT
+	help
+	  Enable support for the I2C video decoder interface on the
+	  Integraphics CyberPro 20x0 and 5000 VGA chips.  This is used
+	  on the Netwinder machines for the SAA7111 video capture.
+
+config FB_APOLLO
+	bool
+	depends on (FB = y) && APOLLO
+	default y
+	select FB_CFB_FILLRECT
+	select FB_CFB_IMAGEBLIT
+
+config FB_Q40
+	bool
+	depends on (FB = y) && Q40
+	default y
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+
+config FB_AMIGA
+	tristate "Amiga native chipset support"
+	depends on FB && AMIGA
+	help
+	  This is the frame buffer device driver for the builtin graphics
+	  chipset found in Amigas.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called amifb.
+
+config FB_AMIGA_OCS
+	bool "Amiga OCS chipset support"
+	depends on FB_AMIGA
+	help
+	  This enables support for the original Agnus and Denise video chips,
+	  found in the Amiga 1000 and most A500's and A2000's. If you intend
+	  to run Linux on any of these systems, say Y; otherwise say N.
+
+config FB_AMIGA_ECS
+	bool "Amiga ECS chipset support"
+	depends on FB_AMIGA
+	help
+	  This enables support for the Enhanced Chip Set, found in later
+	  A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
+	  you intend to run Linux on any of these systems, say Y; otherwise
+	  say N.
+
+config FB_AMIGA_AGA
+	bool "Amiga AGA chipset support"
+	depends on FB_AMIGA
+	help
+	  This enables support for the Advanced Graphics Architecture (also
+	  known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
+	  and CD32. If you intend to run Linux on any of these systems, say Y;
+	  otherwise say N.
+
+config FB_FM2
+	bool "Amiga FrameMaster II/Rainbow II support"
+	depends on (FB = y) && ZORRO
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the Amiga FrameMaster
+	  card from BSC (exhibited 1992 but not shipped as a CBM product).
+
+config FB_ARC
+	tristate "Arc Monochrome LCD board support"
+	depends on FB && (X86 || COMPILE_TEST)
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	help
+	  This enables support for the Arc Monochrome LCD board. The board
+	  is based on the KS-108 lcd controller and is typically a matrix
+	  of 2*n chips. This driver was tested with a 128x64 panel. This
+	  driver supports it for use with x86 SBCs through a 16 bit GPIO
+	  interface (8 bit data, 8 bit control). If you anticipate using
+	  this driver, say Y or M; otherwise say N. You must specify the
+	  GPIO IO address to be used for setting control and data.
+
+config FB_ATARI
+	bool "Atari native chipset support"
+	depends on (FB = y) && ATARI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the builtin graphics
+	  chipset found in Ataris.
+
+config FB_OF
+	bool "Open Firmware frame buffer device support"
+	depends on (FB = y) && PPC && (!PPC_PSERIES || PCI)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MACMODES
+	help
+	  Say Y if you want support with Open Firmware for your graphics
+	  board.
+
+config FB_CONTROL
+	bool "Apple \"control\" display support"
+	depends on (FB = y) && ((PPC_PMAC && PPC32) || COMPILE_TEST)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MACMODES
+	help
+	  This driver supports a frame buffer for the graphics adapter in the
+	  Power Macintosh 7300 and others.
+
+config FB_PLATINUM
+	bool "Apple \"platinum\" display support"
+	depends on (FB = y) && PPC_PMAC && PPC32
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MACMODES
+	help
+	  This driver supports a frame buffer for the "platinum" graphics
+	  adapter in some Power Macintoshes.
+
+config FB_VALKYRIE
+	bool "Apple \"valkyrie\" display support"
+	depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MACMODES
+	help
+	  This driver supports a frame buffer for the "valkyrie" graphics
+	  adapter in some Power Macintoshes.
+
+config FB_CT65550
+	bool "Chips 65550 display support"
+	depends on (FB = y) && PPC32 && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the Chips & Technologies
+	  65550 graphics chip in PowerBooks.
+
+config FB_ASILIANT
+	bool "Asiliant (Chips) 69000 display support"
+	depends on (FB = y) && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the Asiliant 69030 chipset
+
+config FB_IMSTT
+	bool "IMS Twin Turbo display support"
+	depends on (FB = y) && PCI
+	select FB_CFB_IMAGEBLIT
+	select FB_MACMODES if PPC_PMAC
+	help
+	  The IMS Twin Turbo is a PCI-based frame buffer card bundled with
+	  many Macintosh and compatible computers.
+
+config FB_VGA16
+	tristate "VGA 16-color graphics support"
+	depends on FB && (X86 || PPC)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select VGASTATE
+	select FONT_8x16 if FRAMEBUFFER_CONSOLE
+	help
+	  This is the frame buffer device driver for VGA 16 color graphic
+	  cards. Say Y if you have such a card.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called vga16fb.
+
+config FB_STI
+	tristate "HP STI frame buffer device support"
+	depends on FB && PARISC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	default y
+	help
+	  STI refers to the HP "Standard Text Interface" which is a set of
+	  BIOS routines contained in a ROM chip in HP PA-RISC based machines.
+	  Enabling this option will implement the linux framebuffer device
+	  using calls to the STI BIOS routines for initialisation.
+	
+	  If you enable this option, you will get a planar framebuffer device
+	  /dev/fb which will work on the most common HP graphic cards of the
+	  NGLE family, including the artist chips (in the 7xx and Bxxx series),
+	  HCRX, HCRX24, CRX, CRX24 and VisEG series.
+
+	  It is safe to enable this option, so you should probably say "Y".
+
+config FB_MAC
+	bool "Generic Macintosh display support"
+	depends on (FB = y) && MAC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MACMODES
+
+config FB_HP300
+	bool
+	depends on (FB = y) && DIO
+	select FB_CFB_IMAGEBLIT
+	default y
+
+config FB_TGA
+	tristate "TGA/SFB+ framebuffer support"
+	depends on FB && (ALPHA || TC)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select BITREVERSE
+	help
+	  This is the frame buffer device driver for generic TGA and SFB+
+	  graphic cards.  These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
+	  also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
+	  TURBOchannel cards, also known as PMAGD-A, -B and -C.
+
+	  Due to hardware limitations ZLX-E2 and E3 cards are not supported
+	  for DECstation 5000/200 systems.  Additionally due to firmware
+	  limitations these cards may cause troubles with booting DECstation
+	  5000/240 and /260 systems, but are fully supported under Linux if
+	  you manage to get it going. ;-)
+
+	  Say Y if you have one of those.
+
+config FB_UVESA
+	tristate "Userspace VESA VGA graphics support"
+	depends on FB && CONNECTOR
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MODE_HELPERS
+	help
+	  This is the frame buffer driver for generic VBE 2.0 compliant
+	  graphic cards. It can also take advantage of VBE 3.0 features,
+	  such as refresh rate adjustment.
+
+	  This driver generally provides more features than vesafb but
+	  requires a userspace helper application called 'v86d'. See
+	  <file:Documentation/fb/uvesafb.rst> for more information.
+
+	  If unsure, say N.
+
+config FB_VESA
+	bool "VESA VGA graphics support"
+	depends on (FB = y) && X86
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_BOOT_VESA_SUPPORT
+	help
+	  This is the frame buffer device driver for generic VESA 2.0
+	  compliant graphic cards. The older VESA 1.2 cards are not supported.
+	  You will get a boot time penguin logo at no additional cost. Please
+	  read <file:Documentation/fb/vesafb.rst>. If unsure, say Y.
+
+config FB_EFI
+	bool "EFI-based Framebuffer Support"
+	depends on (FB = y) && !IA64 && EFI
+	select DRM_PANEL_ORIENTATION_QUIRKS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the EFI frame buffer device driver. If the firmware on
+	  your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
+	  using the EFI framebuffer as your console.
+
+config FB_N411
+	tristate "N411 Apollo/Hecuba devkit support"
+	depends on FB && X86 && MMU
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	select FB_DEFERRED_IO
+	select FB_HECUBA
+	help
+	  This enables support for the Apollo display controller in its
+	  Hecuba form using the n411 devkit.
+
+config FB_HGA
+	tristate "Hercules mono graphics support"
+	depends on FB && X86
+	help
+	  Say Y here if you have a Hercules mono graphics card.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called hgafb.
+
+	  As this card technology is at least 25 years old,
+	  most people will answer N here.
+
+config FB_GBE
+	bool "SGI Graphics Backend frame buffer support"
+	depends on (FB = y) && HAS_IOMEM
+	depends on SGI_IP32 || COMPILE_TEST
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for SGI Graphics Backend.
+	  This chip is used in SGI O2 and Visual Workstation 320/540.
+
+config FB_GBE_MEM
+	int "Video memory size in MB"
+	depends on FB_GBE
+	default 4
+	help
+	  This is the amount of memory reserved for the framebuffer,
+	  which can be any value between 1MB and 8MB.
+
+config FB_SBUS
+	bool "SBUS and UPA framebuffers"
+	depends on (FB = y) && SPARC
+	help
+	  Say Y if you want support for SBUS or UPA based frame buffer device.
+
+config FB_BW2
+	bool "BWtwo support"
+	depends on (FB = y) && (SPARC && FB_SBUS)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the BWtwo frame buffer.
+
+config FB_CG3
+	bool "CGthree support"
+	depends on (FB = y) && (SPARC && FB_SBUS)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the CGthree frame buffer.
+
+config FB_CG6
+	bool "CGsix (GX,TurboGX) support"
+	depends on (FB = y) && (SPARC && FB_SBUS)
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the CGsix (GX, TurboGX)
+	  frame buffer.
+
+config FB_FFB
+	bool "Creator/Creator3D/Elite3D support"
+	depends on FB_SBUS && SPARC64
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the Creator, Creator3D,
+	  and Elite3D graphics boards.
+
+config FB_TCX
+	bool "TCX (SS4/SS5 only) support"
+	depends on FB_SBUS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the TCX 24/8bit frame
+	  buffer.
+
+config FB_CG14
+	bool "CGfourteen (SX) support"
+	depends on FB_SBUS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the CGfourteen frame
+	  buffer on Desktop SPARCsystems with the SX graphics option.
+
+config FB_P9100
+	bool "P9100 (Sparcbook 3 only) support"
+	depends on FB_SBUS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the P9100 card
+	  supported on Sparcbook 3 machines.
+
+config FB_LEO
+	bool "Leo (ZX) support"
+	depends on FB_SBUS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the SBUS-based Sun ZX
+	  (leo) frame buffer cards.
+
+config FB_XVR500
+	bool "Sun XVR-500 3DLABS Wildcat support"
+	depends on (FB = y) && PCI && SPARC64
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the framebuffer device for the Sun XVR-500 and similar
+	  graphics cards based upon the 3DLABS Wildcat chipset.  The driver
+	  only works on sparc64 systems where the system firmware has
+	  mostly initialized the card already.  It is treated as a
+	  completely dumb framebuffer device.
+
+config FB_XVR2500
+	bool "Sun XVR-2500 3DLABS Wildcat support"
+	depends on (FB = y) && PCI && SPARC64
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the framebuffer device for the Sun XVR-2500 and similar
+	  graphics cards based upon the 3DLABS Wildcat chipset.  The driver
+	  only works on sparc64 systems where the system firmware has
+	  mostly initialized the card already.  It is treated as a
+	  completely dumb framebuffer device.
+
+config FB_XVR1000
+	bool "Sun XVR-1000 support"
+	depends on (FB = y) && SPARC64
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the framebuffer device for the Sun XVR-1000 and similar
+	  graphics cards.  The driver only works on sparc64 systems where
+	  the system firmware has mostly initialized the card already.  It
+	  is treated as a completely dumb framebuffer device.
+
+config FB_PVR2
+	tristate "NEC PowerVR 2 display support"
+	depends on FB && HAS_IOMEM
+	depends on SH_DREAMCAST || COMPILE_TEST
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Say Y here if you have a PowerVR 2 card in your box.  If you plan to
+	  run linux on your Dreamcast, you will have to say Y here.
+	  This driver may or may not work on other PowerVR 2 cards, but is
+	  totally untested.  Use at your own risk.  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called pvr2fb.
+
+	  You can pass several parameters to the driver at boot time or at
+	  module load time.  The parameters look like "video=pvr2:XXX", where
+	  the meaning of XXX can be found at the end of the main source file
+	  (<file:drivers/video/pvr2fb.c>). Please see the file
+	  <file:Documentation/fb/pvr2fb.rst>.
+
+config FB_OPENCORES
+	tristate "OpenCores VGA/LCD core 2.0 framebuffer support"
+	depends on FB && HAS_DMA
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This enables support for the OpenCores VGA/LCD core.
+
+	  The OpenCores VGA/LCD core is typically used together with
+	  softcore CPUs (e.g. OpenRISC or Microblaze) or hard processor
+	  systems (e.g. Altera socfpga or Xilinx Zynq) on FPGAs.
+
+	  The source code and specification for the core is available at
+	  <https://opencores.org/project,vga_lcd>
+
+config FB_S1D13XXX
+	tristate "Epson S1D13XXX framebuffer support"
+	depends on FB
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Support for S1D13XXX framebuffer device family (currently only
+	  working with S1D13806). Product specs at
+	  <https://vdc.epson.com/>
+
+config FB_ATMEL
+	tristate "AT91 LCD Controller support"
+	depends on FB && OF && HAVE_CLK && HAS_IOMEM
+	depends on HAVE_FB_ATMEL || COMPILE_TEST
+	select FB_BACKLIGHT
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MODE_HELPERS
+	select VIDEOMODE_HELPERS
+	help
+	  This enables support for the AT91 LCD Controller.
+
+config FB_NVIDIA
+	tristate "nVidia Framebuffer Support"
+	depends on FB && PCI
+	select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select BITREVERSE
+	select VGASTATE
+	help
+	  This driver supports graphics boards with the nVidia chips, TNT
+	  and newer. For very old chipsets, such as the RIVA128, then use
+	  the rivafb.
+	  Say Y if you have such a graphics board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called nvidiafb.
+
+config FB_NVIDIA_I2C
+	bool "Enable DDC Support"
+	depends on FB_NVIDIA
+	select FB_DDC
+	help
+	  This enables I2C support for nVidia Chipsets.  This is used
+	  only for getting EDID information from the attached display
+	  allowing for robust video mode handling and switching.
+
+	  Because fbdev-2.6 requires that drivers must be able to
+	  independently validate video mode parameters, you should say Y
+	  here.
+
+config FB_NVIDIA_DEBUG
+	bool "Lots of debug output"
+	depends on FB_NVIDIA
+	help
+	  Say Y here if you want the nVidia driver to output all sorts
+	  of debugging information to provide to the maintainer when
+	  something goes wrong.
+
+config FB_NVIDIA_BACKLIGHT
+	bool "Support for backlight control"
+	depends on FB_NVIDIA
+	default y
+	help
+	  Say Y here if you want to control the backlight of your display.
+
+config FB_RIVA
+	tristate "nVidia Riva support"
+	depends on FB && PCI
+	select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select BITREVERSE
+	select VGASTATE
+	help
+	  This driver supports graphics boards with the nVidia Riva/Geforce
+	  chips.
+	  Say Y if you have such a graphics board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called rivafb.
+
+config FB_RIVA_I2C
+	bool "Enable DDC Support"
+	depends on FB_RIVA
+	select FB_DDC
+	help
+	  This enables I2C support for nVidia Chipsets.  This is used
+	  only for getting EDID information from the attached display
+	  allowing for robust video mode handling and switching.
+
+	  Because fbdev-2.6 requires that drivers must be able to
+	  independently validate video mode parameters, you should say Y
+	  here.
+
+config FB_RIVA_DEBUG
+	bool "Lots of debug output"
+	depends on FB_RIVA
+	help
+	  Say Y here if you want the Riva driver to output all sorts
+	  of debugging information to provide to the maintainer when
+	  something goes wrong.
+
+config FB_RIVA_BACKLIGHT
+	bool "Support for backlight control"
+	depends on FB_RIVA
+	default y
+	help
+	  Say Y here if you want to control the backlight of your display.
+
+config FB_I740
+	tristate "Intel740 support"
+	depends on FB && PCI
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select VGASTATE
+	select FB_DDC
+	help
+	  This driver supports graphics cards based on Intel740 chip.
+
+config FB_I810
+	tristate "Intel 810/815 support"
+	depends on FB && PCI && X86_32 && AGP_INTEL
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select VGASTATE
+	help
+	  This driver supports the on-board graphics built in to the Intel 810
+	  and 815 chipsets.  Say Y if you have and plan to use such a board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called i810fb.
+
+	  For more information, please read
+	  <file:Documentation/fb/intel810.rst>
+
+config FB_I810_GTF
+	bool "use VESA Generalized Timing Formula"
+	depends on FB_I810
+	help
+	  If you say Y, then the VESA standard, Generalized Timing Formula
+	  or GTF, will be used to calculate the required video timing values
+	  per video mode.  Since the GTF allows nondiscrete timings
+	  (nondiscrete being a range of values as opposed to discrete being a
+	  set of values), you'll be able to use any combination of horizontal
+	  and vertical resolutions, and vertical refresh rates without having
+	  to specify your own timing parameters.  This is especially useful
+	  to maximize the performance of an aging display, or if you just
+	  have a display with nonstandard dimensions. A VESA compliant
+	  monitor is recommended, but can still work with non-compliant ones.
+	  If you need or want this, then select this option. The timings may
+	  not be compliant with Intel's recommended values. Use at your own
+	  risk.
+
+	  If you say N, the driver will revert to discrete video timings
+	  using a set recommended by Intel in their documentation.
+
+	  If unsure, say N.
+
+config FB_I810_I2C
+	bool "Enable DDC Support"
+	depends on FB_I810 && FB_I810_GTF
+	select FB_DDC
+	help
+	  Add DDC/I2C support for i810fb.  This will allow the driver to get
+	  display information, especially for monitors with fickle timings.
+
+	  If unsure, say Y.
+
+config FB_LE80578
+	tristate "Intel LE80578 (Vermilion) support"
+	depends on FB && PCI && X86
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This driver supports the LE80578 (Vermilion Range) chipset
+
+config FB_CARILLO_RANCH
+	tristate "Intel Carillo Ranch support"
+	depends on FB_LE80578 && FB && PCI && X86
+	help
+	  This driver supports the LE80578 (Carillo Ranch) board
+
+config FB_INTEL
+	tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support"
+	depends on FB && PCI && X86 && AGP_INTEL && EXPERT
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_BOOT_VESA_SUPPORT if FB_INTEL = y
+	depends on !DRM_I915
+	help
+	  This driver supports the on-board graphics built in to the Intel
+	  830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
+	  Say Y if you have and plan to use such a board.
+
+	  To make FB_INTEL=Y work you need to say AGP_INTEL=y too.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called intelfb.
+
+	  For more information, please read <file:Documentation/fb/intelfb.rst>
+
+config FB_INTEL_DEBUG
+	bool "Intel driver Debug Messages"
+	depends on FB_INTEL
+	help
+	  Say Y here if you want the Intel driver to output all sorts
+	  of debugging information to provide to the maintainer when
+	  something goes wrong.
+
+config FB_INTEL_I2C
+	bool "DDC/I2C for Intel framebuffer support"
+	depends on FB_INTEL
+	select FB_DDC
+	default y
+	help
+	  Say Y here if you want DDC/I2C support for your on-board Intel graphics.
+
+config FB_MATROX
+	tristate "Matrox acceleration"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_TILEBLITTING
+	select FB_MACMODES if PPC_PMAC
+	help
+	  Say Y here if you have a Matrox Millennium, Matrox Millennium II,
+	  Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
+	  Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
+	  Matrox G400, G450 or G550 card in your box.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called matroxfb.
+
+	  You can pass several parameters to the driver at boot time or at
+	  module load time. The parameters look like "video=matroxfb:XXX", and
+	  are described in <file:Documentation/fb/matroxfb.rst>.
+
+config FB_MATROX_MILLENIUM
+	bool "Millennium I/II support"
+	depends on FB_MATROX
+	help
+	  Say Y here if you have a Matrox Millennium or Matrox Millennium II
+	  video card. If you select "Advanced lowlevel driver options" below,
+	  you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
+	  packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
+	  also use font widths different from 8.
+
+config FB_MATROX_MYSTIQUE
+	bool "Mystique support"
+	depends on FB_MATROX
+	help
+	  Say Y here if you have a Matrox Mystique or Matrox Mystique 220
+	  video card. If you select "Advanced lowlevel driver options" below,
+	  you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
+	  packed pixel and 32 bpp packed pixel. You can also use font widths
+	  different from 8.
+
+config FB_MATROX_G
+	bool "G100/G200/G400/G450/G550 support"
+	depends on FB_MATROX
+	help
+	  Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
+	  video card. If you select "Advanced lowlevel driver options", you
+	  should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
+	  pixel and 32 bpp packed pixel. You can also use font widths
+	  different from 8.
+
+	  If you need support for G400 secondary head, you must say Y to
+	  "Matrox I2C support" and "G400 second head support" right below.
+	  G450/G550 secondary head and digital output are supported without
+	  additional modules.
+
+	  The driver starts in monitor mode. You must use the matroxset tool
+	  (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
+	  swap primary and secondary head outputs, or to change output mode.
+	  Secondary head driver always start in 640x480 resolution and you
+	  must use fbset to change it.
+
+	  Do not forget that second head supports only 16 and 32 bpp
+	  packed pixels, so it is a good idea to compile them into the kernel
+	  too. You can use only some font widths, as the driver uses generic
+	  painting procedures (the secondary head does not use acceleration
+	  engine).
+
+	  G450/G550 hardware can display TV picture only from secondary CRTC,
+	  and it performs no scaling, so picture must have 525 or 625 lines.
+
+config FB_MATROX_I2C
+	tristate "Matrox I2C support"
+	depends on FB_MATROX
+	select FB_DDC
+	help
+	  This drivers creates I2C buses which are needed for accessing the
+	  DDC (I2C) bus present on all Matroxes, an I2C bus which
+	  interconnects Matrox optional devices, like MGA-TVO on G200 and
+	  G400, and the secondary head DDC bus, present on G400 only.
+
+	  You can say Y or M here if you want to experiment with monitor
+	  detection code. You must say Y or M here if you want to use either
+	  second head of G400 or MGA-TVO on G200 or G400.
+
+	  If you compile it as module, it will create a module named
+	  i2c-matroxfb.
+
+config FB_MATROX_MAVEN
+	tristate "G400 second head support"
+	depends on FB_MATROX_G && FB_MATROX_I2C
+	help
+	  WARNING !!! This support does not work with G450 !!!
+
+	  Say Y or M here if you want to use a secondary head (meaning two
+	  monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
+	  head is not compatible with accelerated XFree 3.3.x SVGA servers -
+	  secondary head output is blanked while you are in X. With XFree
+	  3.9.17 preview you can use both heads if you use SVGA over fbdev or
+	  the fbdev driver on first head and the fbdev driver on second head.
+
+	  If you compile it as module, two modules are created,
+	  matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
+	  both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
+	  also load i2c-matroxfb to get it to run.
+
+	  The driver starts in monitor mode and you must use the matroxset
+	  tool (available at
+	  <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
+	  PAL or NTSC or to swap primary and secondary head outputs.
+	  Secondary head driver also always start in 640x480 resolution, you
+	  must use fbset to change it.
+
+	  Also do not forget that second head supports only 16 and 32 bpp
+	  packed pixels, so it is a good idea to compile them into the kernel
+	  too.  You can use only some font widths, as the driver uses generic
+	  painting procedures (the secondary head does not use acceleration
+	  engine).
+
+config FB_RADEON
+	tristate "ATI Radeon display support"
+	depends on FB && PCI
+	select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_MACMODES if PPC
+	help
+	  Choose this option if you want to use an ATI Radeon graphics card as
+	  a framebuffer device.  There are both PCI and AGP versions.  You
+	  don't need to choose this to run the Radeon in plain VGA mode.
+
+	  There is a product page at
+	  https://products.amd.com/en-us/GraphicCardResult.aspx
+
+config FB_RADEON_I2C
+	bool "DDC/I2C for ATI Radeon support"
+	depends on FB_RADEON
+	select FB_DDC
+	default y
+	help
+	  Say Y here if you want DDC/I2C support for your Radeon board.
+
+config FB_RADEON_BACKLIGHT
+	bool "Support for backlight control"
+	depends on FB_RADEON
+	default y
+	help
+	  Say Y here if you want to control the backlight of your display.
+
+config FB_RADEON_DEBUG
+	bool "Lots of debug output from Radeon driver"
+	depends on FB_RADEON
+	help
+	  Say Y here if you want the Radeon driver to output all sorts
+	  of debugging information to provide to the maintainer when
+	  something goes wrong.
+
+config FB_ATY128
+	tristate "ATI Rage128 display support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
+	select FB_MACMODES if PPC_PMAC
+	help
+	  This driver supports graphics boards with the ATI Rage128 chips.
+	  Say Y if you have such a graphics board and read
+	  <file:Documentation/fb/aty128fb.rst>.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called aty128fb.
+
+config FB_ATY128_BACKLIGHT
+	bool "Support for backlight control"
+	depends on FB_ATY128
+	default y
+	help
+	  Say Y here if you want to control the backlight of your display.
+
+config FB_ATY
+	tristate "ATI Mach64 display support" if PCI || ATARI
+	depends on FB && !SPARC32
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_BACKLIGHT if FB_ATY_BACKLIGHT
+	select FB_MACMODES if PPC
+	select FB_ATY_CT if SPARC64 && PCI
+	help
+	  This driver supports graphics boards with the ATI Mach64 chips.
+	  Say Y if you have such a graphics board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called atyfb.
+
+config FB_ATY_CT
+	bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
+	depends on PCI && FB_ATY
+	help
+	  Say Y here to support use of ATI's 64-bit Rage boards (or other
+	  boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
+	  framebuffer device.  The ATI product support page for these boards
+	  is at <http://support.ati.com/products/pc/mach64/mach64.html>.
+
+config FB_ATY_GENERIC_LCD
+	bool "Mach64 generic LCD support"
+	depends on FB_ATY_CT
+	help
+	  Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
+	  Rage XC, or Rage XL chipset.
+
+config FB_ATY_GX
+	bool "Mach64 GX support" if PCI
+	depends on FB_ATY
+	default y if ATARI
+	help
+	  Say Y here to support use of the ATI Mach64 Graphics Expression
+	  board (or other boards based on the Mach64 GX chipset) as a
+	  framebuffer device.  The ATI product support page for these boards
+	  is at
+	  <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
+
+config FB_ATY_BACKLIGHT
+	bool "Support for backlight control"
+	depends on FB_ATY
+	default y
+	help
+	  Say Y here if you want to control the backlight of your display.
+
+config FB_S3
+	tristate "S3 Trio/Virge support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_TILEBLITTING
+	select FB_SVGALIB
+	select VGASTATE
+	select FONT_8x16 if FRAMEBUFFER_CONSOLE
+	help
+	  Driver for graphics boards with S3 Trio / S3 Virge chip.
+
+config FB_S3_DDC
+	bool "DDC for S3 support"
+	depends on FB_S3
+	select FB_DDC
+	default y
+	help
+	  Say Y here if you want DDC support for your S3 graphics card.
+
+config FB_SAVAGE
+	tristate "S3 Savage support"
+	depends on FB && PCI
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select VGASTATE
+	help
+	  This driver supports notebooks and computers with S3 Savage PCI/AGP
+	  chips.
+
+	  Say Y if you have such a graphics card.
+
+	  To compile this driver as a module, choose M here; the module
+	  will be called savagefb.
+
+config FB_SAVAGE_I2C
+	bool "Enable DDC2 Support"
+	depends on FB_SAVAGE
+	select FB_DDC
+	help
+	  This enables I2C support for S3 Savage Chipsets.  This is used
+	  only for getting EDID information from the attached display
+	  allowing for robust video mode handling and switching.
+
+	  Because fbdev-2.6 requires that drivers must be able to
+	  independently validate video mode parameters, you should say Y
+	  here.
+
+config FB_SAVAGE_ACCEL
+	bool "Enable Console Acceleration"
+	depends on FB_SAVAGE
+	help
+	  This option will compile in console acceleration support. If
+	  the resulting framebuffer console has bothersome glitches, then
+	  choose N here.
+
+config FB_SIS
+	tristate "SiS/XGI display support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_BOOT_VESA_SUPPORT if FB_SIS = y
+	select FB_SIS_300 if !FB_SIS_315
+	help
+	  This is the frame buffer device driver for the SiS 300, 315, 330
+	  and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
+	  Specs available at <https://www.sis.com> and <http://www.xgitech.com>.
+
+	  To compile this driver as a module, choose M here; the module
+	  will be called sisfb.
+
+config FB_SIS_300
+	bool "SiS 300 series support"
+	depends on FB_SIS
+	help
+	  Say Y here to support use of the SiS 300/305, 540, 630 and 730.
+
+config FB_SIS_315
+	bool "SiS 315/330/340 series and XGI support"
+	depends on FB_SIS
+	help
+	  Say Y here to support use of the SiS 315, 330 and 340 series
+	  (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
+	  as XGI V3XT, V5, V8 and Z7.
+
+config FB_VIA
+	tristate "VIA UniChrome (Pro) and Chrome9 display support"
+	depends on FB && PCI && GPIOLIB && I2C && (X86 || COMPILE_TEST)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select I2C_ALGOBIT
+	help
+	  This is the frame buffer device driver for Graphics chips of VIA
+	  UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
+	  CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
+	  /P4M900,VX800)
+	  Say Y if you have a VIA UniChrome graphics board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called viafb.
+
+if FB_VIA
+
+config FB_VIA_DIRECT_PROCFS
+	bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)"
+	help
+	  Allow direct hardware access to some output registers via procfs.
+	  This is dangerous but may provide the only chance to get the
+	  correct output device configuration.
+	  Its use is strongly discouraged.
+
+config FB_VIA_X_COMPATIBILITY
+	bool "X server compatibility"
+	help
+	  This option reduces the functionality (power saving, ...) of the
+	  framebuffer to avoid negative impact on the OpenChrome X server.
+	  If you use any X server other than fbdev you should enable this
+	  otherwise it should be safe to disable it and allow using all
+	  features.
+
+endif
+
+config FB_NEOMAGIC
+	tristate "NeoMagic display support"
+	depends on FB && PCI
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select VGASTATE
+	help
+	  This driver supports notebooks with NeoMagic PCI chips.
+	  Say Y if you have such a graphics card.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called neofb.
+
+config FB_KYRO
+	tristate "IMG Kyro support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
+	  graphics board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called kyrofb.
+
+config FB_3DFX
+	tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
+	depends on FB && PCI
+	select FB_CFB_IMAGEBLIT
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_MODE_HELPERS
+	help
+	  This driver supports graphics boards with the 3Dfx Banshee,
+	  Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
+	  such a graphics board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called tdfxfb.
+
+config FB_3DFX_ACCEL
+	bool "3Dfx Acceleration functions"
+	depends on FB_3DFX
+	help
+	This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
+	device driver with acceleration functions.
+
+config FB_3DFX_I2C
+	bool "Enable DDC/I2C support"
+	depends on FB_3DFX
+	select FB_DDC
+	default y
+	help
+	  Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
+
+config FB_VOODOO1
+	tristate "3Dfx Voodoo Graphics (sst1) support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
+	  Voodoo2 (cvg) based graphics card.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sstfb.
+
+	  WARNING: Do not use any application that uses the 3D engine
+	  (namely glide) while using this driver.
+	  Please read the <file:Documentation/fb/sstfb.rst> for supported
+	  options and other important info  support.
+
+config FB_VT8623
+	tristate "VIA VT8623 support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_TILEBLITTING
+	select FB_SVGALIB
+	select VGASTATE
+	select FONT_8x16 if FRAMEBUFFER_CONSOLE
+	help
+	  Driver for CastleRock integrated graphics core in the
+	  VIA VT8623 [Apollo CLE266] chipset.
+
+config FB_TRIDENT
+	tristate "Trident/CyberXXX/CyberBlade support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_DDC
+	select FB_MODE_HELPERS
+	help
+	  This is the frame buffer device driver for Trident PCI/AGP chipsets.
+	  Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
+	  and Blade XP.
+	  There are also integrated versions of these chips called CyberXXXX,
+	  CyberImage or CyberBlade. These chips are mostly found in laptops
+	  but also on some motherboards including early VIA EPIA motherboards.
+	  For more information, read <file:Documentation/fb/tridentfb.rst>
+
+	  Say Y if you have such a graphics board.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called tridentfb.
+
+config FB_ARK
+	tristate "ARK 2000PV support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_TILEBLITTING
+	select FB_SVGALIB
+	select VGASTATE
+	select FONT_8x16 if FRAMEBUFFER_CONSOLE
+	help
+	  Driver for PCI graphics boards with ARK 2000PV chip
+	  and ICS 5342 RAMDAC.
+
+config FB_PM3
+	tristate "Permedia3 support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the 3DLabs Permedia3
+	  chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
+	  similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
+	  and maybe other boards.
+
+config FB_CARMINE
+	tristate "Fujitsu carmine frame buffer support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the Fujitsu Carmine chip.
+	  The driver provides two independent frame buffer devices.
+
+choice
+	depends on FB_CARMINE
+	prompt "DRAM timing"
+	default FB_CARMINE_DRAM_EVAL
+
+config FB_CARMINE_DRAM_EVAL
+	bool "Eval board timings"
+	help
+	  Use timings which work on the eval card.
+
+config CARMINE_DRAM_CUSTOM
+	bool "Custom board timings"
+	help
+	  Use custom board timings.
+endchoice
+
+config FB_AU1100
+	bool "Au1100 LCD Driver"
+	depends on (FB = y) && MIPS_ALCHEMY
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the framebuffer driver for the AMD Au1100 SOC.  It can drive
+	  various panels and CRTs by passing in kernel cmd line option
+	  au1100fb:panel=<name>.
+
+config FB_AU1200
+	bool "Au1200/Au1300 LCD Driver"
+	depends on (FB = y) && MIPS_ALCHEMY
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	help
+	  This is the framebuffer driver for the Au1200/Au1300 SOCs.
+	  It can drive various panels and CRTs by passing in kernel cmd line
+	  option au1200fb:panel=<name>.
+
+config FB_VT8500
+	bool "VIA VT8500 framebuffer support"
+	depends on (FB = y) && ARM && ARCH_VT8500
+	select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
+	select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
+	select FB_SYS_IMAGEBLIT
+	select FB_MODE_HELPERS
+	select VIDEOMODE_HELPERS
+	help
+	  This is the framebuffer driver for VIA VT8500 integrated LCD
+	  controller.
+
+config FB_WM8505
+	bool "Wondermedia WM8xxx-series frame buffer support"
+	depends on (FB = y) && HAS_IOMEM && (ARCH_VT8500 || COMPILE_TEST)
+	select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
+	select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
+	select FB_SYS_IMAGEBLIT
+	select FB_MODE_HELPERS
+	select VIDEOMODE_HELPERS
+	help
+	  This is the framebuffer driver for WonderMedia WM8xxx-series
+	  integrated LCD controller. This driver covers the WM8505, WM8650
+	  and WM8850 SoCs.
+
+config FB_WMT_GE_ROPS
+	bool "VT8500/WM8xxx accelerated raster ops support"
+	depends on (FB = y) && (FB_VT8500 || FB_WM8505)
+	help
+	  This adds support for accelerated raster operations on the
+	  VIA VT8500 and Wondermedia 85xx series SoCs.
+
+source "drivers/video/fbdev/geode/Kconfig"
+
+config FB_HIT
+	tristate "HD64461 Frame Buffer support"
+	depends on FB && HD64461
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  This is the frame buffer device driver for the Hitachi HD64461 LCD
+	  frame buffer card.
+
+config FB_PMAG_AA
+	tristate "PMAG-AA TURBOchannel framebuffer support"
+	depends on FB && TC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
+	  used mainly in the MIPS-based DECstation series.
+
+config FB_PMAG_BA
+	tristate "PMAG-BA TURBOchannel framebuffer support"
+	depends on FB && TC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
+	  used mainly in the MIPS-based DECstation series.
+
+config FB_PMAGB_B
+	tristate "PMAGB-B TURBOchannel framebuffer support"
+	depends on FB && TC
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Support for the PMAGB-B TURBOchannel framebuffer card used mainly
+	  in the MIPS-based DECstation series. The card is currently only
+	  supported in 1280x1024x8 mode.
+
+config FB_MAXINE
+	bool "Maxine (Personal DECstation) onboard framebuffer support"
+	depends on (FB = y) && MACH_DECSTATION
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Support for the onboard framebuffer (1024x768x8) in the Personal
+	  DECstation series (Personal DECstation 5000/20, /25, /33, /50,
+	  Codename "Maxine").
+
+config FB_G364
+	bool "G364 frame buffer support"
+	depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  The G364 driver is the framebuffer used in MIPS Magnum 4000 and
+	  Olivetti M700-10 systems.
+
+config FB_68328
+	bool "Motorola 68328 native frame buffer support"
+	depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Say Y here if you want to support the built-in frame buffer of
+	  the Motorola 68328 CPU family.
+
+config FB_PXA168
+	tristate "PXA168/910 LCD framebuffer support"
+	depends on FB && HAVE_CLK && HAS_IOMEM
+	depends on CPU_PXA168 || CPU_PXA910 || COMPILE_TEST
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for the built-in LCD controller in the Marvell
+	  MMP processor.
+
+config FB_PXA
+	tristate "PXA LCD framebuffer support"
+	depends on FB && ARCH_PXA
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select VIDEOMODE_HELPERS if OF
+	select FB_MODE_HELPERS if OF
+	help
+	  Frame buffer driver for the built-in LCD controller in the Intel
+	  PXA2x0 processor.
+
+	  This driver is also available as a module ( = code which can be
+	  inserted and removed from the running kernel whenever you want). The
+	  module will be called pxafb. If you want to compile it as a module,
+	  say M here and read <file:Documentation/kbuild/modules.rst>.
+
+	  If unsure, say N.
+
+config FB_PXA_OVERLAY
+	bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
+	depends on FB_PXA && (PXA27x || PXA3xx)
+
+config FB_PXA_SMARTPANEL
+	bool "PXA Smartpanel LCD support"
+	depends on FB_PXA
+
+config FB_PXA_PARAMETERS
+	bool "PXA LCD command line parameters"
+	depends on FB_PXA
+	help
+	  Enable the use of kernel command line or module parameters
+	  to configure the physical properties of the LCD panel when
+	  using the PXA LCD driver.
+
+	  This option allows you to override the panel parameters
+	  supplied by the platform in order to support multiple
+	  different models of flatpanel. If you will only be using a
+	  single model of flatpanel then you can safely leave this
+	  option disabled.
+
+	  <file:Documentation/fb/pxafb.rst> describes the available parameters.
+
+config PXA3XX_GCU
+	tristate "PXA3xx 2D graphics accelerator driver"
+	depends on FB_PXA
+	help
+	  Kernelspace driver for the 2D graphics controller unit (GCU)
+	  found on PXA3xx processors. There is a counterpart driver in the
+	  DirectFB suite, see http://www.directfb.org/
+
+	  If you compile this as a module, it will be called pxa3xx_gcu.
+
+config FB_FSL_DIU
+	tristate "Freescale DIU framebuffer support"
+	depends on FB && FSL_SOC
+	select FB_MODE_HELPERS
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select PPC_LIB_RHEAP
+	help
+	  Framebuffer driver for the Freescale SoC DIU
+
+config FB_W100
+	tristate "W100 frame buffer support"
+	depends on FB && HAS_IOMEM && (ARCH_PXA || COMPILE_TEST)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
+	  It can also drive the w3220 chip found on iPAQ hx4700.
+
+	  This driver is also available as a module ( = code which can be
+	  inserted and removed from the running kernel whenever you want). The
+	  module will be called w100fb. If you want to compile it as a module,
+	  say M here and read <file:Documentation/kbuild/modules.rst>.
+
+	  If unsure, say N.
+
+config FB_SH_MOBILE_LCDC
+	tristate "SuperH Mobile LCDC framebuffer support"
+	depends on FB && HAVE_CLK && HAS_IOMEM
+	depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	select FB_DEFERRED_IO
+	select FB_BACKLIGHT
+	help
+	  Frame buffer driver for the on-chip SH-Mobile LCD controller.
+
+config FB_TMIO
+	tristate "Toshiba Mobile IO FrameBuffer support"
+	depends on FB && (MFD_TMIO || COMPILE_TEST)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for the Toshiba Mobile IO integrated as found
+	  on the Sharp SL-6000 series
+
+	  This driver is also available as a module ( = code which can be
+	  inserted and removed from the running kernel whenever you want). The
+	  module will be called tmiofb. If you want to compile it as a module,
+	  say M here and read <file:Documentation/kbuild/modules.rst>.
+
+	  If unsure, say N.
+
+config FB_TMIO_ACCELL
+	bool "tmiofb acceleration"
+	depends on FB_TMIO
+	default y
+
+config FB_S3C
+	tristate "Samsung S3C framebuffer support"
+	depends on FB && HAVE_CLK && HAS_IOMEM
+	depends on (CPU_S3C2416 || ARCH_S3C64XX) || COMPILE_TEST
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for the built-in FB controller in the Samsung
+	  SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
+	  and the S3C64XX series such as the S3C6400 and S3C6410.
+
+	  These chips all have the same basic framebuffer design with the
+	  actual capabilities depending on the chip. For instance the S3C6400
+	  and S3C6410 support 4 hardware windows whereas the S3C24XX series
+	  currently only have two.
+
+	  Currently the support is only for the S3C6400 and S3C6410 SoCs.
+
+config FB_S3C_DEBUG_REGWRITE
+	bool "Debug register writes"
+	depends on FB_S3C
+	help
+	  Show all register writes via pr_debug()
+
+config FB_S3C2410
+	tristate "S3C2410 LCD framebuffer support"
+	depends on FB && ARCH_S3C24XX
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for the built-in LCD controller in the Samsung
+	  S3C2410 processor.
+
+	  This driver is also available as a module ( = code which can be
+	  inserted and removed from the running kernel whenever you want). The
+	  module will be called s3c2410fb. If you want to compile it as a module,
+	  say M here and read <file:Documentation/kbuild/modules.rst>.
+
+	  If unsure, say N.
+config FB_S3C2410_DEBUG
+	bool "S3C2410 lcd debug messages"
+	depends on FB_S3C2410
+	help
+	  Turn on debugging messages. Note that you can set/unset at run time
+	  through sysfs
+
+config FB_SM501
+	tristate "Silicon Motion SM501 framebuffer support"
+	depends on FB && MFD_SM501
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for the CRT and LCD controllers in the Silicon
+	  Motion SM501.
+
+	  This driver is also available as a module ( = code which can be
+	  inserted and removed from the running kernel whenever you want). The
+	  module will be called sm501fb. If you want to compile it as a module,
+	  say M here and read <file:Documentation/kbuild/modules.rst>.
+
+	  If unsure, say N.
+
+config FB_SMSCUFX
+	tristate "SMSC UFX6000/7000 USB Framebuffer support"
+	depends on FB && USB
+	select FB_MODE_HELPERS
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	select FB_DEFERRED_IO
+	help
+	  This is a kernel framebuffer driver for SMSC UFX USB devices.
+	  Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
+	  mplayer -vo fbdev. Supports both UFX6000 (USB 2.0) and UFX7000
+	  (USB 3.0) devices.
+	  To compile as a module, choose M here: the module name is smscufx.
+
+config FB_UDL
+	tristate "Displaylink USB Framebuffer support"
+	depends on FB && USB
+	select FB_MODE_HELPERS
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	select FB_DEFERRED_IO
+	help
+	  This is a kernel framebuffer driver for DisplayLink USB devices.
+	  Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
+	  mplayer -vo fbdev. Supports all USB 2.0 era DisplayLink devices.
+	  To compile as a module, choose M here: the module name is udlfb.
+
+config FB_IBM_GXT4500
+	tristate "Framebuffer support for IBM GXT4000P/4500P/6000P/6500P adaptors"
+	depends on FB
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Say Y here to enable support for the IBM GXT4000P/6000P and
+	  GXT4500P/6500P display adaptor based on Raster Engine RC1000,
+	  found on some IBM System P (pSeries) machines. This driver
+	  doesn't use Geometry Engine GT1000. This driver also supports
+	  AGP Fire GL2/3/4 cards on x86.
+
+config FB_PS3
+	tristate "PS3 GPU framebuffer driver"
+	depends on FB && PS3_PS3AV
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	help
+	  Include support for the virtual frame buffer in the PS3 platform.
+
+config FB_PS3_DEFAULT_SIZE_M
+	int "PS3 default frame buffer size (in MiB)"
+	depends on FB_PS3
+	default 9
+	help
+	  This is the default size (in MiB) of the virtual frame buffer in
+	  the PS3.
+	  The default value can be overridden on the kernel command line
+	  using the "ps3fb" option (e.g. "ps3fb=9M");
+
+config FB_XILINX
+	tristate "Xilinx frame buffer support"
+	depends on FB && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Include support for the Xilinx ML300/ML403 reference design
+	  framebuffer. ML300 carries a 640*480 LCD display on the board,
+	  ML403 uses a standard DB15 VGA connector.
+
+config FB_GOLDFISH
+	tristate "Goldfish Framebuffer"
+	depends on FB
+	depends on GOLDFISH || COMPILE_TEST
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Framebuffer driver for Goldfish Virtual Platform
+
+config FB_COBALT
+	tristate "Cobalt server LCD frame buffer support"
+	depends on FB && MIPS_COBALT
+
+config FB_SH7760
+	bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
+	depends on FB=y && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
+		|| CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Support for the SH7760/SH7763/SH7720/SH7721 integrated
+	  (D)STN/TFT LCD Controller.
+	  Supports display resolutions up to 1024x1024 pixel, grayscale and
+	  color operation, with depths ranging from 1 bpp to 8 bpp monochrome
+	  and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
+	  panels <= 320 pixel horizontal resolution.
+
+config FB_DA8XX
+	tristate "DA8xx/OMAP-L1xx/AM335x Framebuffer support"
+	depends on FB && HAVE_CLK && HAS_IOMEM
+	depends on ARCH_DAVINCI_DA8XX || SOC_AM33XX || COMPILE_TEST
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_CFB_REV_PIXELS_IN_BYTE
+	select FB_MODE_HELPERS
+	select VIDEOMODE_HELPERS
+	help
+	  This is the frame buffer device driver for the TI LCD controller
+	  found on DA8xx/OMAP-L1xx/AM335x SoCs.
+	  If unsure, say N.
+
+config FB_VIRTUAL
+	tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
+	depends on FB
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	help
+	  This is a `virtual' frame buffer device. It operates on a chunk of
+	  unswappable kernel memory instead of on the memory of a graphics
+	  board. This means you cannot see any output sent to this frame
+	  buffer device, while it does consume precious memory. The main use
+	  of this frame buffer device is testing and debugging the frame
+	  buffer subsystem. Do NOT enable it for normal systems! To protect
+	  the innocent, it has to be enabled explicitly at boot time using the
+	  kernel option `video=vfb:'.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called vfb. In order to load it, you must use
+	  the vfb_enable=1 option.
+
+	  If unsure, say N.
+
+config XEN_FBDEV_FRONTEND
+	tristate "Xen virtual frame buffer support"
+	depends on FB && XEN
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	select FB_DEFERRED_IO
+	select XEN_XENBUS_FRONTEND
+	default y
+	help
+	  This driver implements the front-end of the Xen virtual
+	  frame buffer driver.  It communicates with a back-end
+	  in another domain.
+
+config FB_METRONOME
+	tristate "E-Ink Metronome/8track controller support"
+	depends on FB
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	select FB_DEFERRED_IO
+	help
+	  This driver implements support for the E-Ink Metronome
+	  controller. The pre-release name for this device was 8track
+	  and could also have been called by some vendors as PVI-nnnn.
+
+config FB_MB862XX
+	tristate "Fujitsu MB862xx GDC support"
+	depends on FB
+	depends on PCI || (OF && PPC)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
+
+choice
+	prompt "GDC variant"
+	depends on FB_MB862XX
+
+config FB_MB862XX_PCI_GDC
+	bool "Carmine/Coral-P(A) GDC"
+	depends on PCI
+	help
+	  This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
+	  PCI graphics controller devices.
+
+config FB_MB862XX_LIME
+	bool "Lime GDC"
+	depends on OF && PPC
+	select FB_FOREIGN_ENDIAN
+	select FB_LITTLE_ENDIAN
+	help
+	  Framebuffer support for Fujitsu Lime GDC on host CPU bus.
+
+endchoice
+
+config FB_MB862XX_I2C
+	bool "Support I2C bus on MB862XX GDC"
+	depends on FB_MB862XX && I2C
+	depends on FB_MB862XX=m || I2C=y
+	default y
+	help
+	  Selecting this option adds Coral-P(A)/Lime GDC I2C bus adapter
+	  driver to support accessing I2C devices on controller's I2C bus.
+	  These are usually some video decoder chips.
+
+config FB_EP93XX
+	tristate "EP93XX frame buffer support"
+	depends on FB && ARCH_EP93XX
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Framebuffer driver for the Cirrus Logic EP93XX series of processors.
+	  This driver is also available as a module. The module will be called
+	  ep93xx-fb.
+
+config FB_PRE_INIT_FB
+	bool "Don't reinitialize, use bootloader's GDC/Display configuration"
+	depends on FB && FB_MB862XX_LIME
+	help
+	  Select this option if display contents should be inherited as set by
+	  the bootloader.
+
+config FB_MX3
+	tristate "MX3 Framebuffer support"
+	depends on FB && MX3_IPU
+	select BACKLIGHT_CLASS_DEVICE
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	default y
+	help
+	  This is a framebuffer device for the i.MX31 LCD Controller. So
+	  far only synchronous displays are supported. If you plan to use
+	  an LCD display with your i.MX31 system, say Y here.
+
+config FB_BROADSHEET
+	tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
+	depends on FB && (ARCH_PXA || COMPILE_TEST)
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	select FB_DEFERRED_IO
+	help
+	  This driver implements support for the E-Ink Broadsheet
+	  controller. The release name for this device was Epson S1D13521
+	  and could also have been called by other names when coupled with
+	  a bridge adapter.
+
+config FB_HYPERV
+	tristate "Microsoft Hyper-V Synthetic Video support"
+	depends on FB && HYPERV
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select FB_DEFERRED_IO
+	select DMA_CMA if HAVE_DMA_CONTIGUOUS && CMA
+	help
+	  This framebuffer driver supports Microsoft Hyper-V Synthetic Video.
+
+config FB_SIMPLE
+	bool "Simple framebuffer support"
+	depends on (FB = y)
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Say Y if you want support for a simple frame-buffer.
+
+	  This driver assumes that the display hardware has been initialized
+	  before the kernel boots, and the kernel will simply render to the
+	  pre-allocated frame buffer surface.
+
+	  Configuration re: surface address, size, and format must be provided
+	  through device tree, or plain old platform data.
+
+config FB_SSD1307
+	tristate "Solomon SSD1307 framebuffer support"
+	depends on FB && I2C
+	depends on OF
+	depends on GPIOLIB || COMPILE_TEST
+	select FB_SYS_FOPS
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_DEFERRED_IO
+	select FB_BACKLIGHT
+	help
+	  This driver implements support for the Solomon SSD1307
+	  OLED controller over I2C.
+
+config FB_SM712
+	tristate "Silicon Motion SM712 framebuffer support"
+	depends on FB && PCI
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	help
+	  Frame buffer driver for the Silicon Motion SM710, SM712, SM721
+	  and SM722 chips.
+
+	  This driver is also available as a module. The module will be
+	  called sm712fb. If you want to compile it as a module, say M
+	  here and read <file:Documentation/kbuild/modules.rst>.
+
+source "drivers/video/fbdev/omap/Kconfig"
+source "drivers/video/fbdev/omap2/Kconfig"
+source "drivers/video/fbdev/mmp/Kconfig"