diff options
Diffstat (limited to '')
-rw-r--r-- | Documentation/ABI/stable/sysfs-driver-mlxreg-io | 225 |
1 files changed, 225 insertions, 0 deletions
diff --git a/Documentation/ABI/stable/sysfs-driver-mlxreg-io b/Documentation/ABI/stable/sysfs-driver-mlxreg-io new file mode 100644 index 000000000..fd9a8045b --- /dev/null +++ b/Documentation/ABI/stable/sysfs-driver-mlxreg-io @@ -0,0 +1,225 @@ +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/asic_health +Date: June 2018 +KernelVersion: 4.19 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file shows ASIC health status. The possible values are: + 0 - health failed, 2 - health OK, 3 - ASIC in booting state. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld1_version +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld2_version +Date: June 2018 +KernelVersion: 4.19 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show with which CPLD versions have been burned + on carrier and switch boards. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/fan_dir +Date: December 2018 +KernelVersion: 5.0 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file shows the system fans direction: + forward direction - relevant bit is set 0; + reversed direction - relevant bit is set 1. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld3_version +Date: November 2018 +KernelVersion: 5.0 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show with which CPLD versions have been burned + on LED or Gearbox board. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/jtag_enable +Date: November 2018 +KernelVersion: 5.0 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files enable and disable the access to the JTAG domain. + By default access to the JTAG domain is disabled. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/select_iio +Date: June 2018 +KernelVersion: 4.19 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file allows iio devices selection. + + Attribute select_iio can be written with 0 or with 1. It + selects which one of iio devices can be accessed. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu1_on + /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu2_on + /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_cycle + /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_down +Date: June 2018 +KernelVersion: 4.19 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files allow asserting system power cycling, switching + power supply units on and off and system's main power domain + shutdown. + Expected behavior: + When pwr_cycle is written 1: auxiliary power domain will go + down and after short period (about 1 second) up. + When psu1_on or psu2_on is written 1, related unit will be + disconnected from the power source, when written 0 - connected. + If both are written 1 - power supplies main power domain will + go down. + When pwr_down is written 1, system's main power domain will go + down. + + The files are write only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_aux_pwr_or_ref +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_asic_thermal +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_hotswap_or_halt +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_hotswap_or_wd +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_fw_reset +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_long_pb +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_main_pwr_fail +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_short_pb +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_sw_reset +Date: June 2018 +KernelVersion: 4.19 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show the system reset cause, as following: power + auxiliary outage or power refresh, ASIC thermal shutdown, halt, + hotswap, watchdog, firmware reset, long press power button, + short press power button, software reset. Value 1 in file means + this is reset cause, 0 - otherwise. Only one of the above + causes could be 1 at the same time, representing only last + reset cause. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_comex_pwr_fail +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_from_comex +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_system +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_voltmon_upgrade_fail +Date: November 2018 +KernelVersion: 5.0 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show the system reset cause, as following: ComEx + power fail, reset from ComEx, system platform reset, reset + due to voltage monitor devices upgrade failure, + Value 1 in file means this is reset cause, 0 - otherwise. + Only one bit could be 1 at the same time, representing only + the last reset cause. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld4_version +Date: November 2018 +KernelVersion: 5.0 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show with which CPLD versions have been burned + on LED board. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_comex_thermal +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_comex_wd +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_from_asic +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_reload_bios +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_sff_wd +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_swb_wd +Date: June 2019 +KernelVersion: 5.3 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show the system reset cause, as following: + COMEX thermal shutdown; wathchdog power off or reset was derived + by one of the next components: COMEX, switch board or by Small Form + Factor mezzanine, reset requested from ASIC, reset cuased by BIOS + reload. Value 1 in file means this is reset cause, 0 - otherwise. + Only one of the above causes could be 1 at the same time, representing + only last reset cause. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/config1 +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/config2 +Date: January 2020 +KernelVersion: 5.6 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show system static topology identification + like system's static I2C topology, number and type of FPGA + devices within the system and so on. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_ac_pwr_fail +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_platform +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_soc +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_sw_pwr_off +Date: January 2020 +KernelVersion: 5.6 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show the system reset causes, as following: reset + due to AC power failure, reset invoked from software by + assertion reset signal through CPLD. reset caused by signal + asserted by SOC through ACPI register, reset invoked from + software by assertion power off signal through CPLD. + + The files are read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pcie_asic_reset_dis +Date: January 2020 +KernelVersion: 5.6 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file allows to retain ASIC up during PCIe root complex + reset, when attribute is set 1. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/vpd_wp +Date: January 2020 +KernelVersion: 5.6 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file allows to overwrite system VPD hardware wrtie + protection when attribute is set 1. + + The file is read/write. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/voltreg_update_status +Date: January 2020 +KernelVersion: 5.6 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file exposes the configuration update status of burnable + voltage regulator devices. The status values are as following: + 0 - OK; 1 - CRC failure; 2 = I2C failure; 3 - in progress. + + The file is read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/ufm_version +Date: January 2020 +KernelVersion: 5.6 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: This file exposes the firmware version of burnable voltage + regulator devices. + + The file is read only. + +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld1_pn +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld2_pn +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld3_pn +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld4_pn +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld1_version_min +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld2_version_min +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld3_version_min +What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld4_version_min +Date: July 2020 +KernelVersion: 5.9 +Contact: Vadim Pasternak <vadimpmellanox.com> +Description: These files show with which CPLD part numbers and minor + versions have been burned CPLD devices equipped on a + system. + + The files are read only. |