diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt | 270 |
1 files changed, 270 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt new file mode 100644 index 000000000..6064d98b1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -0,0 +1,270 @@ +NXP i.MX System Controller Firmware (SCFW) +-------------------------------------------------------------------- + +The System Controller Firmware (SCFW) is a low-level system function +which runs on a dedicated Cortex-M core to provide power, clock, and +resource management. It exists on some i.MX8 processors. e.g. i.MX8QM +(QM, QP), and i.MX8QX (QXP, DX). + +The AP communicates with the SC using a multi-ported MU module found +in the LSIO subsystem. The current definition of this MU module provides +5 remote AP connections to the SC to support up to 5 execution environments +(TZ, HV, standard Linux, etc.). The SC side of this MU module interfaces +with the LSIO DSC IP bus. The SC firmware will communicate with this MU +using the MSI bus. + +System Controller Device Node: +============================================================ + +The scu node with the following properties shall be under the /firmware/ node. + +Required properties: +------------------- +- compatible: should be "fsl,imx-scu". +- mbox-names: should include "tx0", "tx1", "tx2", "tx3", + "rx0", "rx1", "rx2", "rx3"; + include "gip3" if want to support general MU interrupt. +- mboxes: List of phandle of 4 MU channels for tx, 4 MU channels for + rx, and 1 optional MU channel for general interrupt. + All MU channels must be in the same MU instance. + Cross instances are not allowed. The MU instance can only + be one of LSIO MU0~M4 for imx8qxp and imx8qm. Users need + to make sure use the one which is not conflict with other + execution environments. e.g. ATF. + Note: + Channel 0 must be "tx0" or "rx0". + Channel 1 must be "tx1" or "rx1". + Channel 2 must be "tx2" or "rx2". + Channel 3 must be "tx3" or "rx3". + General interrupt rx channel must be "gip3". + e.g. + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 0 1 + &lsio_mu1 0 2 + &lsio_mu1 0 3 + &lsio_mu1 1 0 + &lsio_mu1 1 1 + &lsio_mu1 1 2 + &lsio_mu1 1 3 + &lsio_mu1 3 3>; + See Documentation/devicetree/bindings/mailbox/fsl,mu.yaml + for detailed mailbox binding. + +Note: Each mu which supports general interrupt should have an alias correctly +numbered in "aliases" node. +e.g. +aliases { + mu1 = &lsio_mu1; +}; + +i.MX SCU Client Device Node: +============================================================ + +Client nodes are maintained as children of the relevant IMX-SCU device node. + +Power domain bindings based on SCU Message Protocol +------------------------------------------------------------ + +This binding for the SCU power domain providers uses the generic power +domain binding[2]. + +Required properties: +- compatible: Should be one of: + "fsl,imx8qm-scu-pd", + "fsl,imx8qxp-scu-pd" + followed by "fsl,scu-pd" + +- #power-domain-cells: Must be 1. Contains the Resource ID used by + SCU commands. + See detailed Resource ID list from: + include/dt-bindings/firmware/imx/rsrc.h + +Clock bindings based on SCU Message Protocol +------------------------------------------------------------ + +This binding uses the common clock binding[1]. + +Required properties: +- compatible: Should be one of: + "fsl,imx8qm-clock" + "fsl,imx8qxp-clock" + followed by "fsl,scu-clk" +- #clock-cells: Should be 1. Contains the Clock ID value. +- clocks: List of clock specifiers, must contain an entry for + each required entry in clock-names +- clock-names: Should include entries "xtal_32KHz", "xtal_24MHz" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. + +See the full list of clock IDs from: +include/dt-bindings/clock/imx8qxp-clock.h + +Pinctrl bindings based on SCU Message Protocol +------------------------------------------------------------ + +This binding uses the i.MX common pinctrl binding[3]. + +Required properties: +- compatible: Should be one of: + "fsl,imx8qm-iomuxc", + "fsl,imx8qxp-iomuxc", + "fsl,imx8dxl-iomuxc". + +Required properties for Pinctrl sub nodes: +- fsl,pins: Each entry consists of 3 integers which represents + the mux and config setting for one pin. The first 2 + integers <pin_id mux_mode> are specified using a + PIN_FUNC_ID macro, which can be found in + <dt-bindings/pinctrl/pads-imx8qm.h>, + <dt-bindings/pinctrl/pads-imx8qxp.h>, + <dt-bindings/pinctrl/pads-imx8dxl.h>. + The last integer CONFIG is the pad setting value like + pull-up on this pin. + + Please refer to i.MX8QXP Reference Manual for detailed + CONFIG settings. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/power/power-domain.yaml +[3] Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt + +RTC bindings based on SCU Message Protocol +------------------------------------------------------------ + +Required properties: +- compatible: should be "fsl,imx8qxp-sc-rtc"; + +OCOTP bindings based on SCU Message Protocol +------------------------------------------------------------ +Required properties: +- compatible: Should be one of: + "fsl,imx8qm-scu-ocotp", + "fsl,imx8qxp-scu-ocotp". +- #address-cells: Must be 1. Contains byte index +- #size-cells: Must be 1. Contains byte length + +Optional Child nodes: + +- Data cells of ocotp: + Detailed bindings are described in bindings/nvmem/nvmem.txt + +Watchdog bindings based on SCU Message Protocol +------------------------------------------------------------ + +Required properties: +- compatible: should be: + "fsl,imx8qxp-sc-wdt" + followed by "fsl,imx-sc-wdt"; +Optional properties: +- timeout-sec: contains the watchdog timeout in seconds. + +SCU key bindings based on SCU Message Protocol +------------------------------------------------------------ + +Required properties: +- compatible: should be: + "fsl,imx8qxp-sc-key" + followed by "fsl,imx-sc-key"; +- linux,keycodes: See Documentation/devicetree/bindings/input/input.yaml + +Thermal bindings based on SCU Message Protocol +------------------------------------------------------------ + +Required properties: +- compatible: Should be : + "fsl,imx8qxp-sc-thermal" + followed by "fsl,imx-sc-thermal"; + +- #thermal-sensor-cells: See Documentation/devicetree/bindings/thermal/thermal-sensor.yaml + for a description. + +Example (imx8qxp): +------------- +aliases { + mu1 = &lsio_mu1; +}; + +lsio_mu1: mailbox@5d1c0000 { + ... + #mbox-cells = <2>; +}; + +firmware { + scu { + compatible = "fsl,imx-scu"; + mbox-names = "tx0", "tx1", "tx2", "tx3", + "rx0", "rx1", "rx2", "rx3", + "gip3"; + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 0 1 + &lsio_mu1 0 2 + &lsio_mu1 0 3 + &lsio_mu1 1 0 + &lsio_mu1 1 1 + &lsio_mu1 1 2 + &lsio_mu1 1 3 + &lsio_mu1 3 3>; + + clk: clk { + compatible = "fsl,imx8qxp-clk", "fsl,scu-clk"; + #clock-cells = <1>; + }; + + iomuxc { + compatible = "fsl,imx8qxp-iomuxc"; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + SC_P_UART0_RX_ADMA_UART0_RX 0x06000020 + SC_P_UART0_TX_ADMA_UART0_TX 0x06000020 + >; + }; + ... + }; + + ocotp: imx8qx-ocotp { + compatible = "fsl,imx8qxp-scu-ocotp"; + #address-cells = <1>; + #size-cells = <1>; + + fec_mac0: mac@2c4 { + reg = <0x2c4 8>; + }; + }; + + pd: imx8qx-pd { + compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd"; + #power-domain-cells = <1>; + }; + + rtc: rtc { + compatible = "fsl,imx8qxp-sc-rtc"; + }; + + scu_key: scu-key { + compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; + linux,keycodes = <KEY_POWER>; + }; + + watchdog { + compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt"; + timeout-sec = <60>; + }; + + tsens: thermal-sensor { + compatible = "fsl,imx8qxp-sc-thermal", "fsl,imx-sc-thermal"; + #thermal-sensor-cells = <1>; + }; + }; +}; + +serial@5a060000 { + ... + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + clocks = <&clk IMX8QXP_UART0_CLK>, + <&clk IMX8QXP_UART0_IPG_CLK>; + clock-names = "per", "ipg"; + power-domains = <&pd IMX_SC_R_UART_0>; +}; |