diff options
Diffstat (limited to 'Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt')
-rw-r--r-- | Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt | 133 |
1 files changed, 133 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt new file mode 100644 index 000000000..576462fae --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt @@ -0,0 +1,133 @@ +NVIDIA Tegra Power Management Controller (PMC) + +Required properties: +- compatible: Should contain one of the following: + - "nvidia,tegra186-pmc": for Tegra186 + - "nvidia,tegra194-pmc": for Tegra194 + - "nvidia,tegra234-pmc": for Tegra234 +- reg: Must contain an (offset, length) pair of the register set for each + entry in reg-names. +- reg-names: Must include the following entries: + - "pmc" + - "wake" + - "aotag" + - "scratch" + - "misc" (Only for Tegra194 and later) + +Optional properties: +- nvidia,invert-interrupt: If present, inverts the PMU interrupt signal. +- interrupt-controller: Identifies the node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value must be 2. + +Example: + +SoC DTSI: + + pmc@c3600000 { + compatible = "nvidia,tegra186-pmc"; + reg = <0 0x0c360000 0 0x10000>, + <0 0x0c370000 0 0x10000>, + <0 0x0c380000 0 0x10000>, + <0 0x0c390000 0 0x10000>; + reg-names = "pmc", "wake", "aotag", "scratch"; + }; + +Board DTS: + + pmc@c360000 { + nvidia,invert-interrupt; + }; + +== Pad Control == + +On Tegra SoCs a pad is a set of pins which are configured as a group. +The pin grouping is a fixed attribute of the hardware. The PMC can be +used to set pad power state and signaling voltage. A pad can be either +in active or power down mode. The support for power state and signaling +voltage configuration varies depending on the pad in question. 3.3 V and +1.8 V signaling voltages are supported on pins where software +controllable signaling voltage switching is available. + +Pad configurations are described with pin configuration nodes which +are placed under the pmc node and they are referred to by the pinctrl +client properties. For more information see +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt. + +The following pads are present on Tegra186: +csia csib dsi mipi-bias +pex-clk-bias pex-clk3 pex-clk2 pex-clk1 +usb0 usb1 usb2 usb-bias +uart audio hsic dbg +hdmi-dp0 hdmi-dp1 pex-cntrl sdmmc2-hv +sdmmc4 cam dsib dsic +dsid csic csid csie +dsif spi ufs dmic-hv +edp sdmmc1-hv sdmmc3-hv conn +audio-hv ao-hv + +Required pin configuration properties: + - pins: A list of strings, each of which contains the name of a pad + to be configured. + +Optional pin configuration properties: + - low-power-enable: Configure the pad into power down mode + - low-power-disable: Configure the pad into active mode + - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or + TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages. + The values are defined in + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h. + +Note: The power state can be configured on all of the above pads except + for ao-hv. Following pads have software configurable signaling + voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv, + ao-hv. + +Pad configuration state example: + pmc: pmc@7000e400 { + compatible = "nvidia,tegra186-pmc"; + reg = <0 0x0c360000 0 0x10000>, + <0 0x0c370000 0 0x10000>, + <0 0x0c380000 0 0x10000>, + <0 0x0c390000 0 0x10000>; + reg-names = "pmc", "wake", "aotag", "scratch"; + + ... + + sdmmc1_3v3: sdmmc1-3v3 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>; + }; + + sdmmc1_1v8: sdmmc1-1v8 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>; + }; + + hdmi_off: hdmi-off { + pins = "hdmi"; + low-power-enable; + } + + hdmi_on: hdmi-on { + pins = "hdmi"; + low-power-disable; + } + }; + +Pinctrl client example: + sdmmc1: sdhci@3400000 { + ... + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + }; + + ... + + sor0: sor@15540000 { + ... + pinctrl-0 = <&hdmi_off>; + pinctrl-1 = <&hdmi_on>; + pinctrl-names = "hdmi-on", "hdmi-off"; + }; |