summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/display/imx/ldb.txt
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/display/imx/ldb.txt147
1 files changed, 147 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt
new file mode 100644
index 000000000..8e6e7d797
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/imx/ldb.txt
@@ -0,0 +1,147 @@
+Device-Tree bindings for LVDS Display Bridge (ldb)
+
+LVDS Display Bridge
+===================
+
+The LVDS Display Bridge device tree node contains up to two lvds-channel
+nodes describing each of the two LVDS encoder channels of the bridge.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
+ Both LDB versions are similar, but i.MX6 has an additional
+ multiplexer in the front to select any of the four IPU display
+ interfaces as input for each LVDS channel.
+ - gpr : should be <&gpr> on i.MX53 and i.MX6q.
+ The phandle points to the iomuxc-gpr region containing the LVDS
+ control register.
+- clocks, clock-names : phandles to the LDB divider and selector clocks and to
+ the display interface selector clocks, as described in
+ Documentation/devicetree/bindings/clock/clock-bindings.txt
+ The following clocks are expected on i.MX53:
+ "di0_pll" - LDB LVDS channel 0 mux
+ "di1_pll" - LDB LVDS channel 1 mux
+ "di0" - LDB LVDS channel 0 gate
+ "di1" - LDB LVDS channel 1 gate
+ "di0_sel" - IPU1 DI0 mux
+ "di1_sel" - IPU1 DI1 mux
+ On i.MX6q the following additional clocks are needed:
+ "di2_sel" - IPU2 DI0 mux
+ "di3_sel" - IPU2 DI1 mux
+ The needed clock numbers for each are documented in
+ Documentation/devicetree/bindings/clock/imx5-clock.yaml, and in
+ Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
+
+Optional properties:
+ - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
+ - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
+ not used on i.MX6q
+ - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
+ be configured - one input will be distributed on both outputs in dual
+ channel mode
+
+LVDS Channel
+============
+
+Each LVDS Channel has to contain either an of graph link to a panel device node
+or a display-timings node that describes the video timings for the connected
+LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
+
+Required properties:
+ - reg : should be <0> or <1>
+ - port: Input and output port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/graph.txt.
+ On i.MX5, the internal two-input-multiplexer is used. Due to hardware
+ limitations, only one input port (port@[0,1]) can be used for each channel
+ (lvds-channel@[0,1], respectively).
+ On i.MX6, there should be four input ports (port@[0-3]) that correspond
+ to the four LVDS multiplexer inputs.
+ A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
+ to a panel input port. Optionally, the output port can be left out if
+ display-timings are used instead.
+
+Optional properties (required if display-timings are used):
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+ - display-timings : A node that describes the display timings as defined in
+ Documentation/devicetree/bindings/display/panel/display-timing.txt.
+ - fsl,data-mapping : should be "spwg" or "jeida"
+ This describes how the color bits are laid out in the
+ serialized LVDS signal.
+ - fsl,data-width : should be <18> or <24>
+
+example:
+
+gpr: iomuxc-gpr@53fa8000 {
+ /* ... */
+};
+
+ldb: ldb@53fa8008 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx53-ldb";
+ gpr = <&gpr>;
+ clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
+ <&clks IMX5_CLK_LDB_DI1_SEL>,
+ <&clks IMX5_CLK_IPU_DI0_SEL>,
+ <&clks IMX5_CLK_IPU_DI1_SEL>,
+ <&clks IMX5_CLK_LDB_DI0_GATE>,
+ <&clks IMX5_CLK_LDB_DI1_GATE>;
+ clock-names = "di0_pll", "di1_pll",
+ "di0_sel", "di1_sel",
+ "di0", "di1";
+
+ /* Using an of-graph endpoint link to connect the panel */
+ lvds-channel@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lvds0_in: endpoint {
+ remote-endpoint = <&ipu_di0_lvds0>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ /* Using display-timings and fsl,data-mapping/width instead */
+ lvds-channel@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+
+ display-timings {
+ /* ... */
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lvds1_in: endpoint {
+ remote-endpoint = <&ipu_di1_lvds1>;
+ };
+ };
+ };
+};
+
+panel: lvds-panel {
+ /* ... */
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+};