diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/display/tilcdc/panel.txt | 66 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt | 82 |
2 files changed, 148 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/tilcdc/panel.txt b/Documentation/devicetree/bindings/display/tilcdc/panel.txt new file mode 100644 index 000000000..808216310 --- /dev/null +++ b/Documentation/devicetree/bindings/display/tilcdc/panel.txt @@ -0,0 +1,66 @@ +Device-Tree bindings for tilcdc DRM generic panel output driver + +Required properties: + - compatible: value should be "ti,tilcdc,panel". + - panel-info: configuration info to configure LCDC correctly for the panel + - ac-bias: AC Bias Pin Frequency + - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt + - dma-burst-sz: DMA burst size + - bpp: Bits per pixel + - fdd: FIFO DMA Request Delay + - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling + - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore + - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most + - fifo-th: DMA FIFO threshold + - display-timings: typical videomode of lcd panel. Multiple video modes + can be listed if the panel supports multiple timings, but the 'native-mode' + should be the preferred/default resolution. Refer to + Documentation/devicetree/bindings/display/panel/display-timing.txt for display + timing binding details. + +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- enable-gpios: GPIO pin to enable or disable the panel + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + /* Settings for CDTech_S035Q01 / LCD3 cape: */ + lcd3 { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + backlight = <&backlight>; + enable-gpios = <&gpio3 19 0>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 320x240 { + hactive = <320>; + vactive = <240>; + hback-porch = <21>; + hfront-porch = <58>; + hsync-len = <47>; + vback-porch = <11>; + vfront-porch = <23>; + vsync-len = <2>; + clock-frequency = <8000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt new file mode 100644 index 000000000..3e64075ac --- /dev/null +++ b/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt @@ -0,0 +1,82 @@ +Device-Tree bindings for tilcdc DRM driver + +Required properties: + - compatible: value should be one of the following: + - "ti,am33xx-tilcdc" for AM335x based boards + - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards + - interrupts: the interrupt number + - reg: base address and size of the LCDC device + +Recommended properties: + - ti,hwmods: Name of the hwmod associated to the LCDC + +Optional properties: + - max-bandwidth: The maximum pixels per second that the memory + interface / lcd controller combination can sustain + - max-width: The maximum horizontal pixel width supported by + the lcd controller. + - max-pixelclock: The maximum pixel clock that can be supported + by the lcd controller in KHz. + - blue-and-red-wiring: Recognized values "straight" or "crossed". + This property deals with the LCDC revision 2 (found on AM335x) + color errata [1]. + - "straight" indicates normal wiring that supports RGB565, + BGR888, and XBGR8888 color formats. + - "crossed" indicates wiring that has blue and red wires + crossed. This setup supports BGR565, RGB888 and XRGB8888 + formats. + - If the property is not present or its value is not recognized + the legacy mode is assumed. This configuration supports RGB565, + RGB888 and XRGB8888 formats. However, depending on wiring, the red + and blue colors are swapped in either 16 or 24-bit color modes. + +Optional nodes: + + - port/ports: to describe a connection to an external encoder. The + binding follows Documentation/devicetree/bindings/graph.txt and + supports a single port with a single endpoint. + + - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and + Documentation/devicetree/bindings/display/bridge/ti,tfp410.yaml for connecting + tfp410 DVI encoder or lcd panel to lcdc + +[1] There is an errata about AM335x color wiring. For 16-bit color mode + the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]), + but for 24 bit color modes the wiring of blue and red components is + crossed and LCD_DATA[0:4] is for Red[3:7] and LCD_DATA[11:15] is + for Blue[3-7]. For more details see section 3.1.1 in AM335x + Silicon Errata: + https://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360 + +Example: + + fb: fb@4830e000 { + compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + + blue-and-red-wiring = "crossed"; + + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; + }; + + tda19988: tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + port { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; |