summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/dma/ste-dma40.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/dma/ste-dma40.txt')
-rw-r--r--Documentation/devicetree/bindings/dma/ste-dma40.txt138
1 files changed, 138 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt
new file mode 100644
index 000000000..99ab5c4d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt
@@ -0,0 +1,138 @@
+* DMA40 DMA Controller
+
+Required properties:
+- compatible: "stericsson,dma40"
+- reg: Address range of the DMAC registers
+- reg-names: Names of the above areas to use during resource look-up
+- interrupt: Should contain the DMAC interrupt number
+- #dma-cells: must be <3>
+- memcpy-channels: Channels to be used for memcpy
+
+Optional properties:
+- dma-channels: Number of channels supported by hardware - if not present
+ the driver will attempt to obtain the information from H/W
+- disabled-channels: Channels which can not be used
+
+Example:
+
+ dma: dma-controller@801c0000 {
+ compatible = "stericsson,db8500-dma40", "stericsson,dma40";
+ reg = <0x801C0000 0x1000 0x40010000 0x800>;
+ reg-names = "base", "lcpa";
+ interrupt-parent = <&intc>;
+ interrupts = <0 25 0x4>;
+
+ #dma-cells = <2>;
+ memcpy-channels = <56 57 58 59 60>;
+ disabled-channels = <12>;
+ dma-channels = <8>;
+ };
+
+Clients
+Required properties:
+- dmas: Comma separated list of dma channel requests
+- dma-names: Names of the aforementioned requested channels
+
+Each dmas request consists of 4 cells:
+ 1. A phandle pointing to the DMA controller
+ 2. Device signal number, the signal line for single and burst requests
+ connected from the device to the DMA40 engine
+ 3. The DMA request line number (only when 'use fixed channel' is set)
+ 4. A 32bit mask specifying; mode, direction and endianness
+ [NB: This list will grow]
+ 0x00000001: Mode:
+ Logical channel when unset
+ Physical channel when set
+ 0x00000002: Direction:
+ Memory to Device when unset
+ Device to Memory when set
+ 0x00000004: Endianness:
+ Little endian when unset
+ Big endian when set
+ 0x00000008: Use fixed channel:
+ Use automatic channel selection when unset
+ Use DMA request line number when set
+ 0x00000010: Set channel as high priority:
+ Normal priority when unset
+ High priority when set
+
+Existing signal numbers for the DB8500 ASIC. Unless specified, the signals are
+bidirectional, i.e. the same for RX and TX operations:
+
+0: SPI controller 0
+1: SD/MMC controller 0 (unused)
+2: SD/MMC controller 1 (unused)
+3: SD/MMC controller 2 (unused)
+4: I2C port 1
+5: I2C port 3
+6: I2C port 2
+7: I2C port 4
+8: Synchronous Serial Port SSP0
+9: Synchronous Serial Port SSP1
+10: Multi-Channel Display Engine MCDE RX
+11: UART port 2
+12: UART port 1
+13: UART port 0
+14: Multirate Serial Port MSP2
+15: I2C port 0
+16: USB OTG in/out endpoints 7 & 15
+17: USB OTG in/out endpoints 6 & 14
+18: USB OTG in/out endpoints 5 & 13
+19: USB OTG in/out endpoints 4 & 12
+20: SLIMbus or HSI channel 0
+21: SLIMbus or HSI channel 1
+22: SLIMbus or HSI channel 2
+23: SLIMbus or HSI channel 3
+24: Multimedia DSP SXA0
+25: Multimedia DSP SXA1
+26: Multimedia DSP SXA2
+27: Multimedia DSP SXA3
+28: SD/MM controller 2
+29: SD/MM controller 0
+30: MSP port 1 on DB8500 v1, MSP port 3 on DB8500 v2
+31: MSP port 0 or SLIMbus channel 0
+32: SD/MM controller 1
+33: SPI controller 2
+34: i2c3 RX2 TX2
+35: SPI controller 1
+36: USB OTG in/out endpoints 3 & 11
+37: USB OTG in/out endpoints 2 & 10
+38: USB OTG in/out endpoints 1 & 9
+39: USB OTG in/out endpoints 8
+40: SPI controller 3
+41: SD/MM controller 3
+42: SD/MM controller 4
+43: SD/MM controller 5
+44: Multimedia DSP SXA4
+45: Multimedia DSP SXA5
+46: SLIMbus channel 8 or Multimedia DSP SXA6
+47: SLIMbus channel 9 or Multimedia DSP SXA7
+48: Crypto Accelerator 1
+49: Crypto Accelerator 1 TX or Hash Accelerator 1 TX
+50: Hash Accelerator 1 TX
+51: memcpy TX (to be used by the DMA driver for memcpy operations)
+52: SLIMbus or HSI channel 4
+53: SLIMbus or HSI channel 5
+54: SLIMbus or HSI channel 6
+55: SLIMbus or HSI channel 7
+56: memcpy (to be used by the DMA driver for memcpy operations)
+57: memcpy (to be used by the DMA driver for memcpy operations)
+58: memcpy (to be used by the DMA driver for memcpy operations)
+59: memcpy (to be used by the DMA driver for memcpy operations)
+60: memcpy (to be used by the DMA driver for memcpy operations)
+61: Crypto Accelerator 0
+62: Crypto Accelerator 0 TX or Hash Accelerator 0 TX
+63: Hash Accelerator 0 TX
+
+Example:
+
+ uart@80120000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x80120000 0x1000>;
+ interrupts = <0 11 0x4>;
+
+ dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */
+ <&dma 13 0 0x0>; /* Logical - MemToDev */
+ dma-names = "rx", "rx";
+
+ };