diff options
Diffstat (limited to '')
10 files changed, 412 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt b/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt new file mode 100644 index 000000000..624bd76f4 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt @@ -0,0 +1,21 @@ +FAIRCHILD SEMICONDUCTOR FSA9480 MICROUSB SWITCH + +The FSA9480 is a USB port accessory detector and switch. The FSA9480 is fully +controlled using I2C and enables USB data, stereo and mono audio, video, +microphone, and UART data to use a common connector port. + +Required properties: + - compatible : Must be one of + "fcs,fsa9480" + "fcs,fsa880" + - reg : Specifies i2c slave address. Must be 0x25. + - interrupts : Should contain one entry specifying interrupt signal of + interrupt parent to which interrupt pin of the chip is connected. + + Example: + musb@25 { + compatible = "fcs,fsa9480"; + reg = <0x25>; + interrupt-parent = <&gph2>; + interrupts = <7 0>; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-max3355.txt b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt new file mode 100644 index 000000000..f2288ea9e --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt @@ -0,0 +1,21 @@ +Maxim Integrated MAX3355 USB OTG chip +------------------------------------- + +MAX3355 integrates a charge pump and comparators to enable a system with an +integrated USB OTG dual-role transceiver to function as a USB OTG dual-role +device. + +Required properties: +- compatible: should be "maxim,max3355"; +- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's SHDN# pin; +- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's ID_OUT pin. + +Example: + + usb-otg { + compatible = "maxim,max3355"; + maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-palmas.txt b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt new file mode 100644 index 000000000..f61d5af44 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt @@ -0,0 +1,22 @@ +EXTCON FOR PALMAS/TWL CHIPS + +PALMAS USB COMPARATOR +Required Properties: + - compatible: should contain one of: + * "ti,palmas-usb-vid". + * "ti,twl6035-usb-vid". + * "ti,palmas-usb" (DEPRECATED - use "ti,palmas-usb-vid"). + * "ti,twl6035-usb" (DEPRECATED - use "ti,twl6035-usb-vid"). + +Optional Properties: + - ti,wakeup : To enable the wakeup comparator in probe + - ti,enable-id-detection: Perform ID detection. If id-gpio is specified + it performs id-detection using GPIO else using OTG core. + - ti,enable-vbus-detection: Perform VBUS detection. + - id-gpio: gpio for GPIO ID detection. See gpio binding. + - debounce-delay-ms: debounce delay for GPIO ID pin in milliseconds. + +palmas-usb { + compatible = "ti,twl6035-usb", "ti,palmas-usb"; + ti,wakeup; +}; diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml new file mode 100644 index 000000000..4b0f41448 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PTN5150 CC (Configuration Channel) Logic device + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + +description: | + PTN5150 is a small thin low power CC logic chip supporting the USB Type-C + connector application with CC control logic detection and indication + functions. It is interfaced to the host controller using an I2C interface. + +properties: + compatible: + const: nxp,ptn5150 + + int-gpios: + deprecated: true + description: + GPIO pin (input) connected to the PTN5150's INTB pin. + Use "interrupts" instead. + + interrupts: + maxItems: 1 + + reg: + maxItems: 1 + + vbus-gpios: + description: + GPIO pin (output) used to control VBUS. If skipped, no such control + takes place. + +required: + - compatible + - interrupts + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + ptn5150@1d { + compatible = "nxp,ptn5150"; + reg = <0x1d>; + interrupt-parent = <&msmgpio>; + interrupts = <78 IRQ_TYPE_LEVEL_HIGH>; + vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt new file mode 100644 index 000000000..cfcf455ad --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt @@ -0,0 +1,23 @@ + +* Richtek RT8973A - Micro USB Switch device + +The Richtek RT8973A is Micro USB Switch with OVP and I2C interface. The RT8973A +is a USB port accessory detector and switch that is optimized to protect low +voltage system from abnormal high input voltage (up to 28V) and supports high +speed USB operation. Also, RT8973A support 'auto-configuration' mode. +If auto-configuration mode is enabled, RT8973A would control internal h/w patch +for USB D-/D+ switching. + +Required properties: +- compatible: Should be "richtek,rt8973a-muic" +- reg: Specifies the I2C slave address of the MUIC block. It should be 0x14 +- interrupts: Interrupt specifiers for detection interrupt sources. + +Example: + + rt8973a@14 { + compatible = "richtek,rt8973a-muic"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x14>; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt new file mode 100644 index 000000000..fc3888e09 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-sm5502.txt @@ -0,0 +1,21 @@ + +* SM5502 MUIC (Micro-USB Interface Controller) device + +The Silicon Mitus SM5502 is a MUIC (Micro-USB Interface Controller) device +which can detect the state of external accessory when external accessory is +attached or detached and button is pressed or released. It is interfaced to +the host controller using an I2C interface. + +Required properties: +- compatible: Should be "siliconmitus,sm5502-muic" +- reg: Specifies the I2C slave address of the MUIC block. It should be 0x25 +- interrupts: Interrupt specifiers for detection interrupt sources. + +Example: + + sm5502@25 { + compatible = "siliconmitus,sm5502-muic"; + interrupt-parent = <&gpx1>; + interrupts = <5 0>; + reg = <0x25>; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt new file mode 100644 index 000000000..dfc14f71e --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt @@ -0,0 +1,21 @@ +USB GPIO Extcon device + +This is a virtual device used to generate USB cable states from the USB ID pin +connected to a GPIO pin. + +Required properties: +- compatible: Should be "linux,extcon-usb-gpio" + +Either one of id-gpio or vbus-gpio must be present. Both can be present as well. +- id-gpio: gpio for USB ID pin. See gpio binding. +- vbus-gpio: gpio for USB VBUS pin. + +Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: + extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>; + } + + &omap_dwc3_1 { + extcon = <&extcon_usb1>; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml new file mode 100644 index 000000000..20e1ccfc8 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/extcon/extcon-usbc-cros-ec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ChromeOS EC USB Type-C cable and accessories detection + +maintainers: + - Benson Leung <bleung@chromium.org> + - Enric Balletbo i Serra <enric.balletbo@collabora.com> + +description: | + On ChromeOS systems with USB Type C ports, the ChromeOS Embedded Controller is + able to detect the state of external accessories such as display adapters + or USB devices when said accessories are attached or detached. + The node for this device must be under a cros-ec node like google,cros-ec-spi + or google,cros-ec-i2c. + +properties: + compatible: + const: google,extcon-usbc-cros-ec + + google,usb-port-id: + $ref: /schemas/types.yaml#/definitions/uint32 + description: the port id + minimum: 0 + maximum: 255 + +required: + - compatible + - google,usb-port-id + +additionalProperties: false + +examples: + - | + spi0 { + #address-cells = <1>; + #size-cells = <0>; + cros-ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0>; + + usbc_extcon0: extcon0 { + compatible = "google,extcon-usbc-cros-ec"; + google,usb-port-id = <0>; + }; + + usbc_extcon1: extcon1 { + compatible = "google,extcon-usbc-cros-ec"; + google,usb-port-id = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt new file mode 100644 index 000000000..35383adb1 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt @@ -0,0 +1,41 @@ +Qualcomm's PM8941 USB ID Extcon device + +Some Qualcomm PMICs have a "misc" module that can be used to detect when +the USB ID pin has been pulled low or high. + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,pm8941-misc"; + +- reg: + Usage: required + Value type: <u32> + Definition: Should contain the offset to the misc address space + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain the usb id interrupt + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the string "usb_id" for the usb id interrupt + +Example: + + pmic { + usb_id: misc@900 { + compatible = "qcom,pm8941-misc"; + reg = <0x900>; + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "usb_id"; + }; + } + + usb-controller { + extcon = <&usb_id>; + }; diff --git a/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml b/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml new file mode 100644 index 000000000..5fe784f48 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/extcon/wlf,arizona.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs + +maintainers: + - patches@opensource.cirrus.com + +description: | + These devices are audio SoCs with extensive digital capabilities and a + range of analogue I/O. + + This document lists Extcon specific bindings, see the primary binding + document ../mfd/arizona.yaml + +properties: + wlf,hpdet-channel: + description: + Headphone detection channel. ARIZONA_ACCDET_MODE_HPL/1 sets the + headphone detect mode to HPDETL, ARIZONA_ACCDET_MODE_HPR/2 sets it + to HPDETR. If this node is not included or if the value is unknown, + then headphone detection mode is set to HPDETL. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 1 + maximum: 2 + + wlf,use-jd2: + description: + Use the additional JD input along with JD1 for dual pin jack detection. + type: boolean + + wlf,use-jd2-nopull: + description: + Internal pull on JD2 is disabled when used for jack detection. + type: boolean + + wlf,jd-invert: + description: + Invert the polarity of the jack detection switch. + type: boolean + + wlf,micd-software-compare: + description: + Use a software comparison to determine mic presence. + type: boolean + + wlf,micd-detect-debounce: + description: + Additional software microphone detection debounce specified in + milliseconds. + $ref: "/schemas/types.yaml#/definitions/uint32" + + wlf,micd-pol-gpio: + description: + GPIO specifier for the GPIO controlling the headset polarity if one + exists. + maxItems: 1 + + wlf,micd-bias-start-time: + description: + Time allowed for MICBIAS to startup prior to performing microphone + detection, specified as per the ARIZONA_MICD_TIME_XXX defines. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 12 + + wlf,micd-rate: + description: + Delay between successive microphone detection measurements, specified + as per the ARIZONA_MICD_TIME_XXX defines. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 12 + + wlf,micd-dbtime: + description: + Microphone detection hardware debounces specified as the number of + measurements to take. + $ref: "/schemas/types.yaml#/definitions/uint32" + enum: [2, 4] + + wlf,micd-timeout-ms: + description: + Timeout for microphone detection, specified in milliseconds. + $ref: "/schemas/types.yaml#/definitions/uint32" + + wlf,micd-force-micbias: + description: + Force MICBIAS continuously on during microphone detection. + type: boolean + + wlf,micd-configs: + description: + Headset polarity configurations (generally used for detection of + CTIA / OMTP headsets), the field can be of variable length but + should always be a multiple of 3 cells long, each three cell group + represents one polarity configuration. + $ref: "/schemas/types.yaml#/definitions/uint32-matrix" + items: + items: + - description: + The first cell defines the accessory detection pin, zero + will use MICDET1 and 0x2000 will use MICDET2. + enum: [ 0, 0x2000 ] + - description: + The second cell represents the MICBIAS to be used. Zero + will use MICVDD, 1-3 will use MICBIASx. + minimum: 0 + maximum: 3 + - description: + The third cell represents the value of the micd-pol-gpio + pin. + minimum: 0 + maximum: 1 + + wlf,gpsw: + description: + Settings for the general purpose switch, set as one of the + ARIZONA_GPSW_XXX defines. + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 3 + +additionalProperties: true |