4 files changed, 163 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/gnss/gnss.txt b/Documentation/devicetree/bindings/gnss/gnss.txt
new file mode 100644
index 000000000..d6dc9c0d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/gnss/gnss.txt
@@ -0,0 +1,37 @@
+GNSS Receiver DT binding
+
+This documents the binding structure and common properties for GNSS receiver
+devices.
+
+A GNSS receiver node is a node named "gnss" and typically resides on a serial
+bus (e.g. UART, I2C or SPI).
+
+Please refer to the following documents for generic properties:
+
+	Documentation/devicetree/bindings/serial/serial.yaml
+	Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Required properties:
+
+- compatible	: A string reflecting the vendor and specific device the node
+		  represents
+
+Optional properties:
+- lna-supply	: Separate supply for an LNA
+- enable-gpios	: GPIO used to enable the device
+- timepulse-gpios	: Time pulse GPIO
+
+Example:
+
+serial@1234 {
+	compatible = "ns16550a";
+
+	gnss {
+		compatible = "u-blox,neo-8";
+
+		vcc-supply = <&gnss_reg>;
+		timepulse-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+
+		current-speed = <4800>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/gnss/mediatek.txt b/Documentation/devicetree/bindings/gnss/mediatek.txt
new file mode 100644
index 000000000..80cb80281
--- /dev/null
+++ b/Documentation/devicetree/bindings/gnss/mediatek.txt
@@ -0,0 +1,35 @@
+Mediatek-based GNSS Receiver DT binding
+
+Mediatek chipsets are used in GNSS-receiver modules produced by several
+vendors and can use a UART interface.
+
+Please see Documentation/devicetree/bindings/gnss/gnss.txt for generic
+properties.
+
+Required properties:
+
+- compatible	: Must be
+
+			"globaltop,pa6h"
+
+- vcc-supply	: Main voltage regulator (pin name: VCC)
+
+Optional properties:
+
+- current-speed		: Default UART baud rate
+- gnss-fix-gpios	: GPIO used to determine device position fix state
+			  (pin name: FIX, 3D_FIX)
+- reset-gpios		: GPIO used to reset the device (pin name: RESET, NRESET)
+- timepulse-gpios	: Time pulse GPIO (pin name: PPS1, 1PPS)
+- vbackup-supply	: Backup voltage regulator (pin name: VBAT, VBACKUP)
+
+Example:
+
+serial@1234 {
+	compatible = "ns16550a";
+
+	gnss {
+		compatible = "globaltop,pa6h";
+		vcc-supply = <&vcc_3v3>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/gnss/sirfstar.txt b/Documentation/devicetree/bindings/gnss/sirfstar.txt
new file mode 100644
index 000000000..f4252b6b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/gnss/sirfstar.txt
@@ -0,0 +1,46 @@
+SiRFstar-based GNSS Receiver DT binding
+
+SiRFstar chipsets are used in GNSS-receiver modules produced by several
+vendors and can use UART, SPI or I2C interfaces.
+
+Please see Documentation/devicetree/bindings/gnss/gnss.txt for generic
+properties.
+
+Required properties:
+
+- compatible	: Must be one of
+
+			"fastrax,uc430"
+			"linx,r4"
+			"wi2wi,w2sg0004"
+			"wi2wi,w2sg0008i"
+			"wi2wi,w2sg0084i"
+
+- vcc-supply	: Main voltage regulator (pin name: 3V3_IN, VCC, VDD)
+
+Required properties (I2C):
+- reg		: I2C slave address
+
+Required properties (SPI):
+- reg		: SPI chip select address
+
+Optional properties:
+
+- sirf,onoff-gpios	: GPIO used to power on and off device (pin name: ON_OFF)
+- sirf,wakeup-gpios	: GPIO used to determine device power state
+			  (pin name: RFPWRUP, WAKEUP)
+- timepulse-gpios	: Time pulse GPIO (pin name: 1PPS, TM)
+
+Example:
+
+serial@1234 {
+	compatible = "ns16550a";
+
+	gnss {
+		compatible = "wi2wi,w2sg0084i";
+
+		vcc-supply = <&gnss_reg>;
+		sirf,onoff-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		sirf,wakeup-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/gnss/u-blox.txt b/Documentation/devicetree/bindings/gnss/u-blox.txt
new file mode 100644
index 000000000..7cdefd058
--- /dev/null
+++ b/Documentation/devicetree/bindings/gnss/u-blox.txt
@@ -0,0 +1,45 @@
+u-blox GNSS Receiver DT binding
+
+The u-blox GNSS receivers can use UART, DDC (I2C), SPI and USB interfaces.
+
+Please see Documentation/devicetree/bindings/gnss/gnss.txt for generic
+properties.
+
+Required properties:
+
+- compatible	: Must be one of
+
+			"u-blox,neo-6m"
+			"u-blox,neo-8"
+			"u-blox,neo-m8"
+
+- vcc-supply	: Main voltage regulator
+
+Required properties (DDC):
+- reg		: DDC (I2C) slave address
+
+Required properties (SPI):
+- reg		: SPI chip select address
+
+Required properties (USB):
+- reg		: Number of the USB hub port or the USB host-controller port
+                  to which this device is attached
+
+Optional properties:
+
+- timepulse-gpios	: Time pulse GPIO
+- u-blox,extint-gpios	: GPIO connected to the "external interrupt" input pin
+- v-bckp-supply	: Backup voltage regulator
+
+Example:
+
+serial@1234 {
+	compatible = "ns16550a";
+
+	gnss {
+		compatible = "u-blox,neo-8";
+
+		v-bckp-supply = <&gnss_v_bckp_reg>;
+		vcc-supply = <&gnss_vcc_reg>;
+	};
+};