summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt')
-rw-r--r--Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt83
1 files changed, 83 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
new file mode 100644
index 000000000..5d468ecd1
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
@@ -0,0 +1,83 @@
+Broadcom STB "UPG GIO" GPIO controller
+
+The controller's registers are organized as sets of eight 32-bit
+registers with each set controlling a bank of up to 32 pins. A single
+interrupt is shared for all of the banks handled by the controller.
+
+Required properties:
+
+- compatible:
+ Must be "brcm,brcmstb-gpio"
+
+- reg:
+ Define the base and range of the I/O address space containing
+ the brcmstb GPIO controller registers
+
+- #gpio-cells:
+ Should be <2>. The first cell is the pin number (within the controller's
+ pin space), and the second is used for the following:
+ bit[0]: polarity (0 for active-high, 1 for active-low)
+
+- gpio-controller:
+ Specifies that the node is a GPIO controller.
+
+- brcm,gpio-bank-widths:
+ Number of GPIO lines for each bank. Number of elements must
+ correspond to number of banks suggested by the 'reg' property.
+
+Optional properties:
+
+- interrupts:
+ The interrupt shared by all GPIO lines for this controller.
+
+- interrupts-extended:
+ Alternate form of specifying interrupts and parents that allows for
+ multiple parents. This takes precedence over 'interrupts' and
+ 'interrupt-parent'. Wakeup-capable GPIO controllers often route their
+ wakeup interrupt lines through a different interrupt controller than the
+ primary interrupt line, making this property necessary.
+
+- #interrupt-cells:
+ Should be <2>. The first cell is the GPIO number, the second should specify
+ flags. The following subset of flags is supported:
+ - bits[3:0] trigger type and level flags
+ 1 = low-to-high edge triggered
+ 2 = high-to-low edge triggered
+ 4 = active high level-sensitive
+ 8 = active low level-sensitive
+ Valid combinations are 1, 2, 3, 4, 8.
+ See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- interrupt-controller:
+ Marks the device node as an interrupt controller
+
+- wakeup-source:
+ GPIOs for this controller can be used as a wakeup source
+
+Example:
+ upg_gio: gpio@f040a700 {
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+ gpio-controller;
+ interrupt-controller;
+ reg = <0xf040a700 0x80>;
+ interrupt-parent = <&irq0_intc>;
+ interrupts = <0x6>;
+ brcm,gpio-bank-widths = <32 32 32 24>;
+ };
+
+ upg_gio_aon: gpio@f04172c0 {
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+ gpio-controller;
+ interrupt-controller;
+ reg = <0xf04172c0 0x40>;
+ interrupt-parent = <&irq0_aon_intc>;
+ interrupts = <0x6>;
+ interrupts-extended = <&irq0_aon_intc 0x6>,
+ <&aon_pm_l2_intc 0x5>;
+ wakeup-source;
+ brcm,gpio-bank-widths = <18 4>;
+ };