diff options
Diffstat (limited to '')
82 files changed, 4572 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/allwinner,sun6i-a31-p2wi.yaml b/Documentation/devicetree/bindings/i2c/allwinner,sun6i-a31-p2wi.yaml new file mode 100644 index 000000000..6097e8ac4 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/allwinner,sun6i-a31-p2wi.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/allwinner,sun6i-a31-p2wi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 P2WI (Push/Pull 2 Wires Interface) Device Tree Bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + const: allwinner,sun6i-a31-p2wi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + clock-frequency: + minimum: 1 + maximum: 6000000 + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +unevaluatedProperties: false + +examples: + - | + i2c@1f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <100000>; + resets = <&apb0_rst 3>; + #address-cells = <1>; + #size-cells = <0>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/i2c/amlogic,meson6-i2c.yaml b/Documentation/devicetree/bindings/i2c/amlogic,meson6-i2c.yaml new file mode 100644 index 000000000..6ecb0270d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/amlogic,meson6-i2c.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/i2c/amlogic,meson6-i2c.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson I2C Controller + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + - Beniamino Galvani <b.galvani@gmail.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + enum: + - amlogic,meson6-i2c # Meson6, Meson8 and compatible SoCs + - amlogic,meson-gxbb-i2c # GXBB and compatible SoCs + - amlogic,meson-axg-i2c # AXG and compatible SoCs + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + i2c@c8100500 { + compatible = "amlogic,meson6-i2c"; + reg = <0xc8100500 0x20>; + interrupts = <92>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt new file mode 100644 index 000000000..a8a35df41 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt @@ -0,0 +1,22 @@ +Broadcom BCM2835 I2C controller + +Required properties: +- compatible : Should be one of: + "brcm,bcm2711-i2c" + "brcm,bcm2835-i2c" +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks : The clock feeding the I2C controller. + +Recommended properties: +- clock-frequency : desired I2C bus clock frequency in Hz. + +Example: + +i2c@7e205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clk_i2c>; + clock-frequency = <100000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/brcm,brcmstb-i2c.yaml b/Documentation/devicetree/bindings/i2c/brcm,brcmstb-i2c.yaml new file mode 100644 index 000000000..edbca2476 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,brcmstb-i2c.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/brcm,brcmstb-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom STB BSC IIC Master Controller + +maintainers: + - Kamal Dasu <kdasu.kdev@gmail.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + enum: + - brcm,bcm2711-hdmi-i2c + - brcm,brcmstb-i2c + - brcm,brcmper-i2c + + reg: + minItems: 1 + maxItems: 2 + items: + - description: BSC register range + - description: Auto-I2C register range + + reg-names: + items: + - const: bsc + - const: auto-i2c + + interrupts: + maxItems: 1 + + interrupt-names: + maxItems: 1 + + clock-frequency: + enum: + - 46875 + - 50000 + - 93750 + - 97500 + - 187500 + - 200000 + - 375000 + - 390000 + +required: + - compatible + - reg + - clock-frequency + +unevaluatedProperties: false + +if: + properties: + compatible: + contains: + enum: + - brcm,bcm2711-hdmi-i2c + +then: + properties: + reg: + minItems: 2 + + required: + - reg-names + +else: + properties: + reg: + maxItems: 1 + +examples: + - | + bsca: i2c@f0406200 { + clock-frequency = <390000>; + compatible = "brcm,brcmstb-i2c"; + interrupt-parent = <&irq0_intc>; + reg = <0xf0406200 0x58>; + interrupts = <0x18>; + interrupt-names = "upg_bsca"; + }; + + - | + ddc0: i2c@7ef04500 { + compatible = "brcm,bcm2711-hdmi-i2c"; + reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; + reg-names = "bsc", "auto-i2c"; + clock-frequency = <390000>; + }; + +... diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt new file mode 100644 index 000000000..d12cc33cc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt @@ -0,0 +1,46 @@ +Broadcom iProc I2C controller + +Required properties: + +- compatible: + Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c" + +- reg: + Define the base and range of the I/O address space that contain the iProc + I2C controller registers + +- clock-frequency: + This is the I2C bus clock. Need to be either 100000 or 400000 + +- #address-cells: + Always 1 (for I2C addresses) + +- #size-cells: + Always 0 + +Optional properties: + +- interrupts: + Should contain the I2C interrupt. For certain revisions of the I2C + controller, I2C interrupt is unwired to the interrupt controller. In such + case, this property should be left unspecified, and driver will fall back + to polling mode + +- brcm,ape-hsls-addr-mask: + Required for "brcm,iproc-nic-i2c". Host view of address mask into the + 'APE' co-processor. Value must be unsigned, 32-bit + +Example: + i2c0: i2c@18008000 { + compatible = "brcm,iproc-i2c"; + reg = <0x18008000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + + codec: wm8750@1a { + compatible = "wlf,wm8750"; + reg = <0x1a>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt new file mode 100644 index 000000000..1b87b741f --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt @@ -0,0 +1,35 @@ +Broadcom Kona Family I2C +========================= + +This I2C controller is used in the following Broadcom SoCs: + + BCM11130 + BCM11140 + BCM11351 + BCM28145 + BCM28155 + +Required Properties +------------------- +- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c" +- reg: Physical base address and length of controller registers +- interrupts: The interrupt number used by the controller +- clocks: clock specifier for the kona i2c external clock +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Refer to clocks/clock-bindings.txt for generic clock consumer +properties. + +Example: + +i2c@3e016000 { + compatible = "brcm,bcm11351-i2c","brcm,kona-i2c"; + reg = <0x3e016000 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bsc1_clk>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml b/Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml new file mode 100644 index 000000000..1ca1cd19b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/i2c/cdns,i2c-r1p10.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Cadence I2C controller Device Tree Bindings + +maintainers: + - Michal Simek <michal.simek@xilinx.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + enum: + - cdns,i2c-r1p10 # cadence i2c controller version 1.0 + - cdns,i2c-r1p14 # cadence i2c controller version 1.4 + + reg: + maxItems: 1 + + clocks: + minItems: 1 + + interrupts: + maxItems: 1 + + clock-frequency: + minimum: 1 + maximum: 400000 + description: | + Desired operating frequency, in Hz, of the bus. + + clock-name: + const: pclk + description: | + Input clock name. + +required: + - compatible + - reg + - clocks + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + i2c@e0004000 { + compatible = "cdns,i2c-r1p10"; + clocks = <&clkc 38>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xe0004000 0x1000>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/google,cros-ec-i2c-tunnel.yaml b/Documentation/devicetree/bindings/i2c/google,cros-ec-i2c-tunnel.yaml new file mode 100644 index 000000000..b386e4128 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/google,cros-ec-i2c-tunnel.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/i2c/google,cros-ec-i2c-tunnel.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: I2C bus that tunnels through the ChromeOS EC (cros-ec) + +maintainers: + - Doug Anderson <dianders@chromium.org> + - Benson Leung <bleung@chromium.org> + - Enric Balletbo i Serra <enric.balletbo@collabora.com> + +description: | + On some ChromeOS board designs we've got a connection to the EC + (embedded controller) but no direct connection to some devices on the + other side of the EC (like a battery and PMIC). To get access to + those devices we need to tunnel our i2c commands through the EC. + + The node for this device should be under a cros-ec node like + google,cros-ec-spi or google,cros-ec-i2c. + +allOf: + - $ref: i2c-controller.yaml# + +properties: + compatible: + const: google,cros-ec-i2c-tunnel + + google,remote-bus: + description: The EC bus we'd like to talk to. + $ref: /schemas/types.yaml#/definitions/uint32 + +required: + - compatible + - google,remote-bus + +unevaluatedProperties: false + +examples: + - | + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + cros-ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0>; + spi-max-frequency = <5000000>; + + i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + #address-cells = <1>; + #size-cells = <0>; + + google,remote-bus = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-altera.txt b/Documentation/devicetree/bindings/i2c/i2c-altera.txt new file mode 100644 index 000000000..767664f44 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-altera.txt @@ -0,0 +1,39 @@ +* Altera I2C Controller +* This is Altera's synthesizable logic block I2C Controller for use +* in Altera's FPGAs. + +Required properties : + - compatible : should be "altr,softip-i2c-v1.0" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number. + - clocks : phandle to input clock. + - #address-cells = <1>; + - #size-cells = <0>; + +Recommended properties : + - clock-frequency : desired I2C bus clock frequency in Hz. + +Optional properties : + - fifo-size : Size of the RX and TX FIFOs in bytes. + - Child nodes conforming to i2c bus binding + +Example : + + i2c@100080000 { + compatible = "altr,softip-i2c-v1.0"; + reg = <0x00000001 0x00080000 0x00000040>; + interrupt-parent = <&intc>; + interrupts = <0 43 4>; + clocks = <&clk_0>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + fifo-size = <4>; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt new file mode 100644 index 000000000..548a73cde --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -0,0 +1,82 @@ +GPIO-based I2C Arbitration Using a Challenge & Response Mechanism +================================================================= +This uses GPIO lines and a challenge & response mechanism to arbitrate who is +the master of an I2C bus in a multimaster situation. + +In many cases using GPIOs to arbitrate is not needed and a design can use +the standard I2C multi-master rules. Using GPIOs is generally useful in +the case where there is a device on the bus that has errata and/or bugs +that makes standard multimaster mode not feasible. + +Note that this scheme works well enough but has some downsides: +* It is nonstandard (not using standard I2C multimaster) +* Having two masters on a bus in general makes it relatively hard to debug + problems (hard to tell if i2c issues were caused by one master, another, or + some device on the bus). + + +Algorithm: + +All masters on the bus have a 'bus claim' line which is an output that the +others can see. These are all active low with pull-ups enabled. We'll +describe these lines as: + +- OUR_CLAIM: output from us signaling to other hosts that we want the bus +- THEIR_CLAIMS: output from others signaling that they want the bus + +The basic algorithm is to assert your line when you want the bus, then make +sure that the other side doesn't want it also. A detailed explanation is best +done with an example. + +Let's say we want to claim the bus. We: +1. Assert OUR_CLAIM. +2. Waits a little bit for the other sides to notice (slew time, say 10 + microseconds). +3. Check THEIR_CLAIMS. If none are asserted then the we have the bus and we are + done. +4. Otherwise, wait for a few milliseconds and see if THEIR_CLAIMS are released. +5. If not, back off, release the claim and wait for a few more milliseconds. +6. Go back to 1 (until retry time has expired). + + +Required properties: +- compatible: i2c-arb-gpio-challenge +- our-claim-gpio: The GPIO that we use to claim the bus. +- their-claim-gpios: The GPIOs that the other sides use to claim the bus. + Note that some implementations may only support a single other master. +- I2C arbitration bus node. See i2c-arb.txt in this directory. + +Optional properties: +- slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us. +- wait-retry-us: we'll attempt another claim after this many microseconds. + Default is 3000 us. +- wait-free-us: we'll give up after this many microseconds. Default is 50000 us. + + +Example: + i2c@12ca0000 { + compatible = "acme,some-i2c-device"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c-arbitrator { + compatible = "i2c-arb-gpio-challenge"; + + i2c-parent = <&{/i2c@12CA0000}>; + + our-claim-gpio = <&gpf0 3 1>; + their-claim-gpios = <&gpe0 4 1>; + slew-delay-us = <10>; + wait-retry-us = <3000>; + wait-free-us = <50000>; + + i2c-arb { + #address-cells = <1>; + #size-cells = <0>; + + i2c@52 { + // Normal I2C device + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb.txt b/Documentation/devicetree/bindings/i2c/i2c-arb.txt new file mode 100644 index 000000000..59abf9277 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-arb.txt @@ -0,0 +1,35 @@ +Common i2c arbitration bus properties. + +- i2c-arb child node + +Required properties for the i2c-arb child node: +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties for i2c-arb child node: +- Child nodes conforming to i2c bus binding + + +Example : + + /* + An NXP pca9541 I2C bus master selector at address 0x74 + with a NXP pca8574 GPIO expander attached. + */ + + arb@74 { + compatible = "nxp,pca9541"; + reg = <0x74>; + + i2c-arb { + #address-cells = <1>; + #size-cells = <0>; + + gpio@38 { + compatible = "nxp,pca8574"; + reg = <0x38>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt new file mode 100644 index 000000000..b47f6ccb1 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt @@ -0,0 +1,49 @@ +Device tree configuration for the I2C busses on the AST24XX, AST25XX, and AST26XX SoCs. + +Required Properties: +- #address-cells : should be 1 +- #size-cells : should be 0 +- reg : address offset and range of bus +- compatible : should be "aspeed,ast2400-i2c-bus" + or "aspeed,ast2500-i2c-bus" + or "aspeed,ast2600-i2c-bus" +- clocks : root clock of bus, should reference the APB + clock in the second cell +- resets : phandle to reset controller with the reset number in + the second cell +- interrupts : interrupt number + +Optional Properties: +- bus-frequency : frequency of the bus clock in Hz defaults to 100 kHz when not + specified +- multi-master : states that there is another master active on this bus. + +Example: + +i2c { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1e78a000 0x1000>; + + i2c_ic: interrupt-controller@0 { + #interrupt-cells = <1>; + compatible = "aspeed,ast2400-i2c-ic"; + reg = <0x0 0x40>; + interrupts = <12>; + interrupt-controller; + }; + + i2c0: i2c-bus@40 { + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + reg = <0x40 0x40>; + compatible = "aspeed,ast2400-i2c-bus"; + clocks = <&syscon ASPEED_CLK_APB>; + resets = <&syscon ASPEED_RESET_I2C>; + bus-frequency = <100000>; + interrupts = <0>; + interrupt-parent = <&i2c_ic>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt new file mode 100644 index 000000000..2015f50ae --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt @@ -0,0 +1,82 @@ +I2C for Atmel platforms + +Required properties : +- compatible : Must be one of: + "atmel,at91rm9200-i2c", + "atmel,at91sam9261-i2c", + "atmel,at91sam9260-i2c", + "atmel,at91sam9g20-i2c", + "atmel,at91sam9g10-i2c", + "atmel,at91sam9x5-i2c", + "atmel,sama5d4-i2c", + "atmel,sama5d2-i2c", + "microchip,sam9x60-i2c". +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; +- clocks: phandles to input clocks. + +Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 +- dmas: A list of two dma specifiers, one for each entry in dma-names. +- dma-names: should contain "tx" and "rx". +- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO + capable I2C controllers. +- i2c-sda-hold-time-ns: TWD hold time, only available for: + "atmel,sama5d4-i2c", + "atmel,sama5d2-i2c", + "microchip,sam9x60-i2c". +- scl-gpios: specify the gpio related to SCL pin +- sda-gpios: specify the gpio related to SDA pin +- pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c + bus recovery, call it "gpio" state +- Child nodes conforming to i2c bus binding + + +Examples : + +i2c0: i2c@fff84000 { + compatible = "atmel,at91sam9g20-i2c"; + reg = <0xfff84000 0x100>; + interrupts = <12 4 6>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&twi0_clk>; + clock-frequency = <400000>; + + 24c512@50 { + compatible = "atmel,24c512"; + reg = <0x50>; + pagesize = <128>; + } +} + +i2c0: i2c@f8034600 { + compatible = "atmel,sama5d2-i2c"; + reg = <0xf8034600 0x100>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(11)>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(12)>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&flx0>; + atmel,fifo-size = <16>; + i2c-sda-hold-time-ns = <336>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c0>; + pinctrl-1 = <&pinctrl_i2c0_gpio>; + sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>; + scl-gpios = <&pioA 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + + wm8731: wm8731@1a { + compatible = "wm8731"; + reg = <0x1a>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-axxia.txt b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt new file mode 100644 index 000000000..7d53a2b79 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt @@ -0,0 +1,30 @@ +LSI Axxia I2C + +Required properties : +- compatible : Must be "lsi,api2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- #address-cells : Must be <1>; +- #size-cells : Must be <0>; +- clock-names : Must contain "i2c". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. + +Example : + +i2c@2010084000 { + compatible = "lsi,api2c"; + device_type = "i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x20 0x10084000 0x00 0x1000>; + interrupts = <0 19 4>; + clocks = <&clk_per>; + clock-names = "i2c"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt new file mode 100644 index 000000000..c143948b2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt @@ -0,0 +1,27 @@ +Device tree bindings for i2c-cbus-gpio driver + +Required properties: + - compatible = "i2c-cbus-gpio"; + - gpios: clk, dat, sel + - #address-cells = <1>; + - #size-cells = <0>; + +Optional properties: + - child nodes conforming to i2c bus binding + +Example: + +i2c@0 { + compatible = "i2c-cbus-gpio"; + gpios = <&gpio 66 0 /* clk */ + &gpio 65 0 /* dat */ + &gpio 64 0 /* sel */ + >; + #address-cells = <1>; + #size-cells = <0>; + + retu: retu@1 { + compatible = "nokia,retu"; + reg = <0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt new file mode 100644 index 000000000..b745f3706 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt @@ -0,0 +1,43 @@ +* Texas Instruments Davinci/Keystone I2C + +This file provides information, what the device node for the +davinci/keystone i2c interface contains. + +Required properties: +- compatible: "ti,davinci-i2c" or "ti,keystone-i2c"; +- reg : Offset and length of the register set for the device +- clocks: I2C functional clock phandle. + For 66AK2G this property should be set per binding, + Documentation/devicetree/bindings/clock/ti,sci-clk.txt + +SoC-specific Required Properties: + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: + +- power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the I2C device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + +Recommended properties : +- interrupts : standard interrupt property. +- clock-frequency : desired I2C bus clock frequency in Hz. +- ti,has-pfunc: boolean; if defined, it indicates that SoC supports PFUNC + registers. PFUNC registers allow to switch I2C pins to function as + GPIOs, so they can be toggled manually. + +Example (enbw_cmc board): + i2c@1c22000 { + compatible = "ti,davinci-i2c"; + reg = <0x22000 0x1000>; + clock-frequency = <100000>; + interrupts = <15>; + interrupt-parent = <&intc>; + #address-cells = <1>; + #size-cells = <0>; + + dtt@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt new file mode 100644 index 000000000..81b5d5508 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt @@ -0,0 +1,135 @@ +Pinctrl-based I2C Bus DeMux + +This binding describes an I2C bus demultiplexer that uses pin multiplexing to +route the I2C signals, and represents the pin multiplexing configuration using +the pinctrl device tree bindings. This may be used to select one I2C IP core at +runtime which may have a better feature set for a given task than another I2C +IP core on the SoC. The most simple example is to fall back to GPIO bitbanging +if your current runtime configuration hits an errata of the internal IP core. + + +-------------------------------+ + | SoC | + | | +-----+ +-----+ + | +------------+ | | dev | | dev | + | |I2C IP Core1|--\ | +-----+ +-----+ + | +------------+ \-------+ | | | + | |Pinctrl|--|------+--------+ + | +------------+ +-------+ | + | |I2C IP Core2|--/ | + | +------------+ | + | | + +-------------------------------+ + +Required properties: +- compatible: "i2c-demux-pinctrl" +- i2c-parent: List of phandles of I2C masters available for selection. The first + one will be used as default. +- i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C + parents. + +Furthermore, I2C mux properties and child nodes. See i2c-mux.txt in this +directory. + +Example: + +Here is a snipplet for a bus to be demuxed. It contains various i2c clients for +HDMI, so the bus is named "i2c-hdmi": + + i2chdmi: i2c@8 { + + compatible = "i2c-demux-pinctrl"; + i2c-parent = <&gpioi2c>, <&iic2>, <&i2c2>; + i2c-bus-name = "i2c-hdmi"; + #address-cells = <1>; + #size-cells = <0>; + + ak4643: sound-codec@12 { + compatible = "asahi-kasei,ak4643"; + + #sound-dai-cells = <0>; + reg = <0x12>; + }; + + composite-in@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + remote = <&vin1>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep0>; + }; + }; + }; + + hdmi@39 { + compatible = "adi,adv7511w"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; + }; + +And for clarification, here are the snipplets for the i2c-parents: + + gpioi2c: i2c@9 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "i2c-gpio"; + gpios = <&gpio5 6 GPIO_ACTIVE_HIGH /* sda */ + &gpio5 5 GPIO_ACTIVE_HIGH /* scl */ + >; + i2c-gpio,delay-us = <5>; + }; + +... + +&i2c2 { + pinctrl-0 = <&i2c2_pins>; + pinctrl-names = "i2c-hdmi"; + + clock-frequency = <100000>; +}; + +... + +&iic2 { + pinctrl-0 = <&iic2_pins>; + pinctrl-names = "i2c-hdmi"; + + clock-frequency = <100000>; +}; + +Please note: + +- pinctrl properties for the parent I2C controllers need a pinctrl state + with the same name as i2c-bus-name, not "default"! + +- the i2c masters must have their status "disabled". This driver will + enable them at runtime when needed. diff --git a/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt b/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt new file mode 100644 index 000000000..457a098d4 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt @@ -0,0 +1,25 @@ +Conexant Digicolor I2C controller + +Required properties: + - compatible: must be "cnxt,cx92755-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + +Optional properties: +- clock-frequency: the desired I2C bus clock frequency in Hz; in + absence of this property the default value is used (100 kHz). + +Example: + + i2c: i2c@f0000120 { + compatible = "cnxt,cx92755-i2c"; + reg = <0xf0000120 0x10>; + interrupts = <28>; + clocks = <&main_clk>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt new file mode 100644 index 000000000..3b30e54ae --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt @@ -0,0 +1,33 @@ +* Energymicro efm32 i2c controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "energymicro,efm32-i2c" + - interrupts : the interrupt number + - clocks : reference to the module clock + +Recommended properties : + + - clock-frequency : maximal I2C bus clock frequency in Hz. + - energymicro,location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 6] + +Example: + i2c0: i2c@4000a000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "energymicro,efm32-i2c"; + reg = <0x4000a000 0x400>; + interrupts = <9>; + clocks = <&cmu clk_HFPERCLKI2C0>; + clock-frequency = <100000>; + energymicro,location = <3>; + + eeprom@50 { + compatible = "microchip,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt new file mode 100644 index 000000000..2dbc0b62d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -0,0 +1,53 @@ +* Samsung's High Speed I2C controller + +The Samsung's High Speed I2C controller is used to interface with I2C devices +at various speeds ranging from 100khz to 3.4Mhz. + +Required properties: + - compatible: value should be. + -> "samsung,exynos5-hsi2c", (DEPRECATED) + for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5250-hsi2c", for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5260-hsi2c", for i2c compatible with HSI2C available + on Exynos5260 SoCs. + -> "samsung,exynos7-hsi2c", for i2c compatible with HSI2C available + on Exynos7 SoCs. + + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + + - Pinctrl: + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - clock-frequency: Desired operating frequency in Hz of the bus. + -> If not specified, the bus operates in fast-speed mode at + at 100khz. + -> If specified, the bus operates in high-speed mode only if the + clock-frequency is >= 1Mhz. + +Example: + +hsi2c@12ca0000 { + compatible = "samsung,exynos5250-hsi2c"; + reg = <0x12ca0000 0x100>; + interrupts = <56>; + clock-frequency = <100000>; + + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-fsi.txt b/Documentation/devicetree/bindings/i2c/i2c-fsi.txt new file mode 100644 index 000000000..b1be2ceb7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-fsi.txt @@ -0,0 +1,40 @@ +Device-tree bindings for FSI-attached I2C master and busses +----------------------------------------------------------- + +Required properties: + - compatible = "ibm,i2c-fsi"; + - reg = < address size >; : The FSI CFAM address and address + space size. + - #address-cells = <1>; : Number of address cells in child + nodes. + - #size-cells = <0>; : Number of size cells in child nodes. + - child nodes : Nodes to describe busses off the I2C + master. + +Child node required properties: + - reg = < port number > : The port number on the I2C master. + +Child node optional properties: + - child nodes : Nodes to describe devices on the I2C + bus. + +Examples: + + i2c@1800 { + compatible = "ibm,i2c-fsi"; + reg = < 0x1800 0x400 >; + #address-cells = <1>; + #size-cells = <0>; + + i2c-bus@0 { + reg = <0>; + }; + + i2c-bus@1 { + reg = <1>; + + eeprom@50 { + compatible = "vendor,dev-name"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-gate.txt b/Documentation/devicetree/bindings/i2c/i2c-gate.txt new file mode 100644 index 000000000..1846d236e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-gate.txt @@ -0,0 +1,41 @@ +An i2c gate is useful to e.g. reduce the digital noise for RF tuners connected +to the i2c bus. Gates are similar to arbitrators in that you need to perform +some kind of operation to access the i2c bus past the arbitrator/gate, but +there are no competing masters to consider for gates and therefore there is +no arbitration happening for gates. + +Common i2c gate properties. + +- i2c-gate child node + +Required properties for the i2c-gate child node: +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties for i2c-gate child node: +- Child nodes conforming to i2c bus binding + + +Example : + + /* + An Invensense mpu9150 at address 0x68 featuring an on-chip Asahi + Kasei ak8975 compass behind a gate. + */ + + mpu9150@68 { + compatible = "invensense,mpu9150"; + reg = <0x68>; + interrupt-parent = <&gpio1>; + interrupts = <18 1>; + + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + ax8975@c { + compatible = "ak,ak8975"; + reg = <0x0c>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-gpio.yaml b/Documentation/devicetree/bindings/i2c/i2c-gpio.yaml new file mode 100644 index 000000000..cc3aa2a5e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-gpio.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for GPIO bitbanged I2C + +maintainers: + - Wolfram Sang <wolfram@the-dreams.de> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + items: + - const: i2c-gpio + + sda-gpios: + description: + gpio used for the sda signal, this should be flagged as + active high using open drain with (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) + from <dt-bindings/gpio/gpio.h> since the signal is by definition + open drain. + maxItems: 1 + + scl-gpios: + description: + gpio used for the scl signal, this should be flagged as + active high using open drain with (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) + from <dt-bindings/gpio/gpio.h> since the signal is by definition + open drain. + maxItems: 1 + + i2c-gpio,scl-output-only: + description: scl as output only + type: boolean + + i2c-gpio,delay-us: + description: delay between GPIO operations (may depend on each platform) + $ref: /schemas/types.yaml#/definitions/uint32 + + i2c-gpio,timeout-ms: + description: timeout to get data + $ref: /schemas/types.yaml#/definitions/uint32 + + # Deprecated properties, do not use in new device tree sources: + gpios: + minItems: 2 + maxItems: 2 + description: sda and scl gpio, alternative for {sda,scl}-gpios + + i2c-gpio,sda-open-drain: + type: boolean + deprecated: true + description: this means that something outside of our control has put + the GPIO line used for SDA into open drain mode, and that something is + not the GPIO chip. It is essentially an inconsistency flag. + + i2c-gpio,scl-open-drain: + type: boolean + deprecated: true + description: this means that something outside of our control has put the + GPIO line used for SCL into open drain mode, and that something is not + the GPIO chip. It is essentially an inconsistency flag. + +required: + - compatible + - sda-gpios + - scl-gpios + +unevaluatedProperties: false + +... diff --git a/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt new file mode 100644 index 000000000..f98b37401 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt @@ -0,0 +1,24 @@ +I2C for Hisilicon hix5hd2 chipset platform + +Required properties: +- compatible: Must be "hisilicon,hix5hd2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; +- clocks: phandles to input clocks. + +Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 +- Child nodes conforming to i2c bus binding + +Examples: +I2C0@f8b10000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0xf8b10000 0x1000>; + interrupts = <0 38 4>; + clocks = <&clock HIX5HD2_I2C0_RST>; + #address-cells = <1>; + #size-cells = <0>; +} diff --git a/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt new file mode 100644 index 000000000..b6461602d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt @@ -0,0 +1,26 @@ +IMG Serial Control Bus (SCB) I2C Controller + +Required Properties: +- compatible: "img,scb-i2c" +- reg: Physical base address and length of controller registers +- interrupts: Interrupt number used by the controller +- clocks : Should contain a clock specifier for each entry in clock-names +- clock-names : Should contain the following entries: + "scb", for the SCB core clock. + "sys", for the system clock. +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Example: + +i2c@18100000 { + compatible = "img,scb-i2c"; + reg = <0x18100000 0x200>; + interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c0_clk>, <&system_clk>; + clock-names = "scb", "sys"; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.yaml b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.yaml new file mode 100644 index 000000000..29b9447f3 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/i2c-imx-lpi2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Low Power Inter IC (LPI2C) for i.MX + +maintainers: + - Anson Huang <Anson.Huang@nxp.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - fsl,imx7ulp-lpi2c + - fsl,imx8qm-lpi2c + - items: + - const: fsl,imx8qxp-lpi2c + - const: fsl,imx7ulp-lpi2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + assigned-clock-parents: true + assigned-clock-rates: true + assigned-clocks: true + clock-frequency: true + + clock-names: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/imx7ulp-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + i2c@40a50000 { + compatible = "fsl,imx7ulp-lpi2c"; + reg = <0x40A50000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7ULP_CLK_LPI2C7>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.yaml b/Documentation/devicetree/bindings/i2c/i2c-imx.yaml new file mode 100644 index 000000000..f23966b0d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/i2c-imx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX + +maintainers: + - Wolfram Sang <wolfram@the-dreams.de> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + oneOf: + - const: fsl,imx1-i2c + - const: fsl,imx21-i2c + - const: fsl,vf610-i2c + - items: + - const: fsl,imx35-i2c + - const: fsl,imx1-i2c + - items: + - const: fsl,imx7d-i2c + - const: fsl,imx21-i2c + - items: + - enum: + - fsl,imx25-i2c + - fsl,imx27-i2c + - fsl,imx31-i2c + - fsl,imx50-i2c + - fsl,imx51-i2c + - fsl,imx53-i2c + - fsl,imx6q-i2c + - fsl,imx6sl-i2c + - fsl,imx6sx-i2c + - fsl,imx6sll-i2c + - fsl,imx6ul-i2c + - fsl,imx7s-i2c + - fsl,imx8mq-i2c + - fsl,imx8mm-i2c + - fsl,imx8mn-i2c + - fsl,imx8mp-i2c + - const: fsl,imx21-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: ipg + + clock-frequency: + enum: [ 100000, 400000 ] + + dmas: + items: + - description: DMA controller phandle and request line for RX + - description: DMA controller phandle and request line for TX + + dma-names: + items: + - const: rx + - const: tx + + sda-gpios: + maxItems: 1 + + scl-gpios: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/imx5-clock.h> + #include <dt-bindings/clock/vf610-clock.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + i2c@83fc4000 { + compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; + reg = <0x83fc4000 0x4000>; + interrupts = <63>; + clocks = <&clks IMX5_CLK_I2C2_GATE>; + }; + + i2c@40066000 { + compatible = "fsl,vf610-i2c"; + reg = <0x40066000 0x1000>; + interrupts = <71 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_I2C0>; + clock-names = "ipg"; + dmas = <&edma0 0 50>, + <&edma0 0 51>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt b/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt new file mode 100644 index 000000000..dcc8390e0 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt @@ -0,0 +1,20 @@ +i2c Controller on XScale platforms such as IOP3xx and IXP4xx + +Required properties: +- compatible : Must be one of + "intel,iop3xx-i2c" + "intel,ixp4xx-i2c"; +- reg +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding + +Example: + +i2c@c8011000 { + compatible = "intel,ixp4xx-i2c"; + reg = <0xc8011000 0x18>; + interrupts = <33 IRQ_TYPE_LEVEL_LOW>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt b/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt new file mode 100644 index 000000000..4101aa621 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt @@ -0,0 +1,33 @@ +NXP I2C controller for LPC2xxx/178x/18xx/43xx + +Required properties: + - compatible: must be "nxp,lpc1788-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + +Optional properties: +- clock-frequency: the desired I2C bus clock frequency in Hz; in + absence of this property the default value is used (100 kHz). + +Example: +i2c0: i2c@400a1000 { + compatible = "nxp,lpc1788-i2c"; + reg = <0x400a1000 0x1000>; + interrupts = <18>; + clocks = <&ccu1 CLK_APB1_I2C0>; + #address-cells = <1>; + #size-cells = <0>; +}; + +&i2c0 { + clock-frequency = <400000>; + + lm75@48 { + compatible = "nxp,lm75"; + reg = <0x48>; + }; +}; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-mpc.txt b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt new file mode 100644 index 000000000..42a390526 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt @@ -0,0 +1,62 @@ +* I2C + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a + compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, + mpc5200 or mpc5200b. For the mpc5121, an additional node + "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. + +Recommended properties : + + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - fsl,preserve-clocking : boolean; if defined, the clock settings + from the bootloader are preserved (not touched). + - clock-frequency : desired I2C bus clock frequency in Hz. + - fsl,timeout : I2C bus timeout in microseconds. + +Examples : + + /* MPC5121 based board */ + i2c@1740 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c", "fsl-i2c"; + reg = <0x1740 0x20>; + interrupts = <11 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + i2ccontrol@1760 { + compatible = "fsl,mpc5121-i2c-ctrl"; + reg = <0x1760 0x8>; + }; + + /* MPC5200B based board */ + i2c@3d00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; + reg = <0x3d00 0x40>; + interrupts = <2 15 0>; + interrupt-parent = <&mpc5200_pic>; + fsl,preserve-clocking; + }; + + /* MPC8544 base board */ + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8544-i2c", "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + clock-frequency = <400000>; + fsl,timeout = <10000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt new file mode 100644 index 000000000..7f0194fdd --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt @@ -0,0 +1,49 @@ +* MediaTek's I2C controller + +The MediaTek's I2C controller is used to interface with I2C devices. + +Required properties: + - compatible: value should be either of the following. + "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for MediaTek MT2701 + "mediatek,mt2712-i2c": for MediaTek MT2712 + "mediatek,mt6577-i2c": for MediaTek MT6577 + "mediatek,mt6589-i2c": for MediaTek MT6589 + "mediatek,mt6797-i2c", "mediatek,mt6577-i2c": for MediaTek MT6797 + "mediatek,mt7622-i2c": for MediaTek MT7622 + "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623 + "mediatek,mt7629-i2c", "mediatek,mt2712-i2c": for MediaTek MT7629 + "mediatek,mt8173-i2c": for MediaTek MT8173 + "mediatek,mt8183-i2c": for MediaTek MT8183 + "mediatek,mt8192-i2c": for MediaTek MT8192 + "mediatek,mt8516-i2c", "mediatek,mt2712-i2c": for MediaTek MT8516 + - reg: physical base address of the controller and dma base, length of memory + mapped region. + - interrupts: interrupt number to the cpu. + - clock-div: the fixed value for frequency divider of clock source in i2c + module. Each IC may be different. + - clocks: clock name from clock manager + - clock-names: Must include "main" and "dma", "arb" is for multi-master that + one bus has more than two i2c controllers, if enable have-pmic need include + "pmic" extra. + +Optional properties: + - clock-frequency: Frequency in Hz of the bus when transfer, the default value + is 100000. + - mediatek,have-pmic: platform can control i2c form special pmic side. + Only mt6589 and mt8135 support this feature. + - mediatek,use-push-pull: IO config use push-pull mode. + +Example: + + i2c0: i2c@1100d000 { + compatible = "mediatek,mt6577-i2c"; + reg = <0x1100d000 0x70>, + <0x11000300 0x80>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_LOW>; + clock-frequency = <400000>; + mediatek,have-pmic; + clock-div = <16>; + clocks = <&i2c0_ck>, <&ap_dma_ck>; + clock-names = "main", "dma"; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-mt7621.txt b/Documentation/devicetree/bindings/i2c/i2c-mt7621.txt new file mode 100644 index 000000000..bc36f0eb9 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mt7621.txt @@ -0,0 +1,25 @@ +MediaTek MT7621/MT7628 I2C master controller + +Required properties: + +- compatible: Should be one of the following: + - "mediatek,mt7621-i2c": for MT7621/MT7628/MT7688 platforms +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: Address and length of the register set for the device +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. + +Optional properties : + +Example: + +i2c: i2c@900 { + compatible = "mediatek,mt7621-i2c"; + reg = <0x900 0x100>; + #address-cells = <1>; + #size-cells = <0>; + resets = <&rstctrl 16>; + reset-names = "i2c"; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt new file mode 100644 index 000000000..21da3ecbb --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -0,0 +1,81 @@ +GPIO-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses GPIOs to +route the I2C signals. + + +-----+ +-----+ + | dev | | dev | + +------------+ +-----+ +-----+ + | SoC | | | + | | /--------+--------+ + | +------+ | +------+ child bus A, on GPIO value set to 0 + | | I2C |-|--| Mux | + | +------+ | +--+---+ child bus B, on GPIO value set to 1 + | | | \----------+--------+--------+ + | +------+ | | | | | + | | GPIO |-|-----+ +-----+ +-----+ +-----+ + | +------+ | | dev | | dev | | dev | + +------------+ +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-gpio +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +- mux-gpios: list of gpios used to control the muxer +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional properties: +- idle-state: value to set the muxer to when idle. When no value is + given, it defaults to the last value used. + +For each i2c child node, an I2C child bus will be created. They will +be numbered based on their order in the device tree. + +Whenever an access is made to a device on a child bus, the value set +in the relevant node's reg property will be output using the list of +GPIOs, the first in the list holding the least-significant value. + +If an idle state is defined, using the idle-state (optional) property, +whenever an access is not being made to a device on a child bus, the +GPIOs will be set according to the idle value. + +If an idle state is not defined, the most recently used value will be +left programmed into hardware whenever no access is being made to a +device on a child bus. + +Example: + i2cmux { + compatible = "i2c-mux-gpio"; + #address-cells = <1>; + #size-cells = <0>; + mux-gpios = <&gpio1 22 0 &gpio1 23 0>; + i2c-parent = <&i2c1>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 1>; + reset-active-low; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt new file mode 100644 index 000000000..8b444b94e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt @@ -0,0 +1,99 @@ +General Purpose I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses a mux controller +from the mux subsystem to route the I2C signals. + + .-----. .-----. + | dev | | dev | + .------------. '-----' '-----' + | SoC | | | + | | .--------+--------' + | .------. | .------+ child bus A, on MUX value set to 0 + | | I2C |-|--| Mux | + | '------' | '--+---+ child bus B, on MUX value set to 1 + | .------. | | '----------+--------+--------. + | | MUX- | | | | | | + | | Ctrl |-|-----+ .-----. .-----. .-----. + | '------' | | dev | | dev | | dev | + '------------' '-----' '-----' '-----' + +Required properties: +- compatible: i2c-mux +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +- mux-controls: The phandle of the mux controller to use for operating the + mux. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number + is also the mux-controller state described in ../mux/mux-controller.txt + +Optional properties: +- mux-locked: If present, explicitly allow unrelated I2C transactions on the + parent I2C adapter at these times: + + during setup of the multiplexer + + between setup of the multiplexer and the child bus I2C transaction + + between the child bus I2C transaction and releasing of the multiplexer + + during releasing of the multiplexer + However, I2C transactions to devices behind all I2C multiplexers connected + to the same parent adapter that this multiplexer is connected to are blocked + for the full duration of the complete multiplexed I2C transaction (i.e. + including the times covered by the above list). + If mux-locked is not present, the multiplexer is assumed to be parent-locked. + This means that no unrelated I2C transactions are allowed on the parent I2C + adapter for the complete multiplexed I2C transaction. + The properties of mux-locked and parent-locked multiplexers are discussed + in more detail in Documentation/i2c/i2c-topology.rst. + +For each i2c child node, an I2C child bus will be created. They will +be numbered based on their order in the device tree. + +Whenever an access is made to a device on a child bus, the value set +in the relevant node's reg property will be set as the state in the +mux controller. + +Example: + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + i2c-mux { + compatible = "i2c-mux"; + mux-locked; + i2c-parent = <&i2c1>; + + mux-controls = <&mux>; + + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 1>; + reset-active-low; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt new file mode 100644 index 000000000..8b1e49cdc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt @@ -0,0 +1,61 @@ +* Linear Technology / Analog Devices I2C bus switch + +Required Properties: + + - compatible: Must contain one of the following. + "lltc,ltc4305", "lltc,ltc4306" + - reg: The I2C address of the device. + + The following required properties are defined externally: + + - Standard I2C mux properties. See i2c-mux.txt in this directory. + - I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional Properties: + + - enable-gpios: Reference to the GPIO connected to the enable input. + - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all + children in idle state. This is necessary for example, if there are several + multiplexers on the bus and the devices behind them use same I2C addresses. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - ltc,downstream-accelerators-enable: Enables the rise time accelerators + on the downstream port. + - ltc,upstream-accelerators-enable: Enables the rise time accelerators + on the upstream port. + +Example: + + ltc4306: i2c-mux@4a { + compatible = "lltc,ltc4306"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4a>; + + gpio-controller; + #gpio-cells = <2>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt new file mode 100644 index 000000000..7abda506b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -0,0 +1,74 @@ +* NXP PCA954x I2C bus switch + +The driver supports NXP PCA954x and PCA984x I2C mux/switch devices. + +Required Properties: + + - compatible: Must contain one of the following. + "nxp,pca9540", + "nxp,pca9542", + "nxp,pca9543", + "nxp,pca9544", + "nxp,pca9545", + "nxp,pca9546", "nxp,pca9846", + "nxp,pca9547", "nxp,pca9847", + "nxp,pca9548", "nxp,pca9848", + "nxp,pca9849" + + - reg: The I2C address of the device. + + The following required properties are defined externally: + + - Standard I2C mux properties. See i2c-mux.txt in this directory. + - I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the reset input. + - idle-state: if present, overrides i2c-mux-idle-disconnect, + Please refer to Documentation/devicetree/bindings/mux/mux-controller.txt + - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all + children in idle state. This is necessary for example, if there are several + multiplexers on the bus and the devices behind them use same I2C addresses. + - interrupts: Interrupt mapping for IRQ. + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example: + + i2c-switch@74 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + + interrupt-parent = <&ipic>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + eeprom@54 { + compatible = "atmel,24c08"; + reg = <0x54>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt new file mode 100644 index 000000000..33119a98e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt @@ -0,0 +1,93 @@ +Pinctrl-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses pin multiplexing to +route the I2C signals, and represents the pin multiplexing configuration +using the pinctrl device tree bindings. + + +-----+ +-----+ + | dev | | dev | + +------------------------+ +-----+ +-----+ + | SoC | | | + | /----|------+--------+ + | +---+ +------+ | child bus A, on first set of pins + | |I2C|---|Pinmux| | + | +---+ +------+ | child bus B, on second set of pins + | \----|------+--------+--------+ + | | | | | + +------------------------+ +-----+ +-----+ +-----+ + | dev | | dev | | dev | + +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-pinctrl +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. + +Also required are: + +* Standard pinctrl properties that specify the pin mux state for each child + bus. See ../pinctrl/pinctrl-bindings.txt. + +* Standard I2C mux properties. See i2c-mux.txt in this directory. + +* I2C child bus nodes. See i2c-mux.txt in this directory. + +For each named state defined in the pinctrl-names property, an I2C child bus +will be created. I2C child bus numbers are assigned based on the index into +the pinctrl-names property. + +The only exception is that no bus will be created for a state named "idle". If +such a state is defined, it must be the last entry in pinctrl-names. For +example: + + pinctrl-names = "ddc", "pta", "idle" -> ddc = bus 0, pta = bus 1 + pinctrl-names = "ddc", "idle", "pta" -> Invalid ("idle" not last) + pinctrl-names = "idle", "ddc", "pta" -> Invalid ("idle" not last) + +Whenever an access is made to a device on a child bus, the relevant pinctrl +state will be programmed into hardware. + +If an idle state is defined, whenever an access is not being made to a device +on a child bus, the idle pinctrl state will be programmed into hardware. + +If an idle state is not defined, the most recently used pinctrl state will be +left programmed into hardware whenever no access is being made of a device on +a child bus. + +Example: + + i2cmux { + compatible = "i2c-mux-pinctrl"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&i2c1>; + + pinctrl-names = "ddc", "pta", "idle"; + pinctrl-0 = <&state_i2cmux_ddc>; + pinctrl-1 = <&state_i2cmux_pta>; + pinctrl-2 = <&state_i2cmux_idle>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom { + compatible = "eeprom"; + reg = <0x50>; + }; + }; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom { + compatible = "eeprom"; + reg = <0x50>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt new file mode 100644 index 000000000..de00d7fc4 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt @@ -0,0 +1,74 @@ +Register-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses a single register +to route the I2C signals. + +Required properties: +- compatible: i2c-mux-reg +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional properties: +- reg: this pair of <offset size> specifies the register to control the mux. + The <offset size> depends on its parent node. It can be any memory-mapped + address. The size must be either 1, 2, or 4 bytes. If reg is omitted, the + resource of this device will be used. +- little-endian: The existence indicates the register is in little endian. +- big-endian: The existence indicates the register is in big endian. + If both little-endian and big-endian are omitted, the endianness of the + CPU will be used. +- write-only: The existence indicates the register is write-only. +- idle-state: value to set the muxer to when idle. When no value is + given, it defaults to the last value used. + +Whenever an access is made to a device on a child bus, the value set +in the relevant node's reg property will be output to the register. + +If an idle state is defined, using the idle-state (optional) property, +whenever an access is not being made to a device on a child bus, the +register will be set according to the idle value. + +If an idle state is not defined, the most recently used value will be +left programmed into the register. + +Example of a mux on PCIe card, the host is a powerpc SoC (big endian): + + i2c-mux { + /* the <offset size> depends on the address translation + * of the parent device. If omitted, device resource + * will be used instead. The size is to determine + * whether iowrite32, iowrite16, or iowrite8 will be used. + */ + reg = <0x6028 0x4>; + little-endian; /* little endian register on PCIe */ + compatible = "i2c-mux-reg"; + #address-cells = <1>; + #size-cells = <0>; + i2c-parent = <&i2c1>; + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + si5338: clock-generator@70 { + compatible = "silabs,si5338"; + reg = <0x70>; + /* other stuff */ + }; + }; + + i2c@1 { + /* data is written using iowrite32 */ + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + si5338: clock-generator@70 { + compatible = "silabs,si5338"; + reg = <0x70>; + /* other stuff */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux.txt new file mode 100644 index 000000000..b38f58a1c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux.txt @@ -0,0 +1,73 @@ +Common i2c bus multiplexer/switch properties. + +An i2c bus multiplexer/switch will have several child busses that are +numbered uniquely in a device dependent manner. The nodes for an i2c bus +multiplexer/switch will have one child node for each child bus. + +Optional properties: +- #address-cells = <1>; + This property is required if the i2c-mux child node does not exist. + +- #size-cells = <0>; + This property is required if the i2c-mux child node does not exist. + +- i2c-mux + For i2c multiplexers/switches that have child nodes that are a mixture + of both i2c child busses and other child nodes, the 'i2c-mux' subnode + can be used for populating the i2c child busses. If an 'i2c-mux' + subnode is present, only subnodes of this will be considered as i2c + child busses. + +Required properties for the i2c-mux child node: +- #address-cells = <1>; +- #size-cells = <0>; + +Required properties for i2c child bus nodes: +- #address-cells = <1>; +- #size-cells = <0>; +- reg : The sub-bus number. + +Optional properties for i2c child bus nodes: +- Other properties specific to the multiplexer/switch hardware. +- Child nodes conforming to i2c bus binding + + +Example : + + /* + An NXP pca9548 8 channel I2C multiplexer at address 0x70 + with two NXP pca8574 GPIO expanders attached, one each to + ports 3 and 4. + */ + + mux@70 { + compatible = "nxp,pca9548"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + gpio1: gpio@38 { + compatible = "nxp,pca8574"; + reg = <0x38>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + gpio2: gpio@38 { + compatible = "nxp,pca8574"; + reg = <0x38>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.yaml b/Documentation/devicetree/bindings/i2c/i2c-mxs.yaml new file mode 100644 index 000000000..21ae7bce0 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/i2c-mxs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MXS Inter IC (I2C) Controller + +maintainers: + - Shawn Guo <shawnguo@kernel.org> + +properties: + compatible: + enum: + - fsl,imx23-i2c + - fsl,imx28-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-frequency: + enum: [ 100000, 400000 ] + + dmas: + maxItems: 1 + + dma-names: + const: rx-tx + +required: + - compatible + - reg + - interrupts + - dmas + - dma-names + +additionalProperties: false + +examples: + - | + i2c@80058000 { + compatible = "fsl,imx28-i2c"; + reg = <0x80058000 2000>; + interrupts = <111>; + clock-frequency = <100000>; + dmas = <&dma_apbx 6>; + dma-names = "rx-tx"; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt new file mode 100644 index 000000000..72065b0ff --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt @@ -0,0 +1,23 @@ +I2C for Nomadik based systems + +Required (non-standard) properties: + - Nil + +Recommended (non-standard) properties: + - clock-frequency : Maximum bus clock frequency for the device + +Optional (non-standard) properties: + - Nil + +Example : + +i2c@80004000 { + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; + reg = <0x80004000 0x1000>; + interrupts = <0 21 0x4>; + #address-cells = <1>; + #size-cells = <0>; + v-i2c-supply = <&db8500_vape_reg>; + + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt new file mode 100644 index 000000000..6b25a80ae --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -0,0 +1,74 @@ +Device tree configuration for i2c-ocores + +Required properties: +- compatible : "opencores,i2c-ocores" + "aeroflexgaisler,i2cmst" + "sifive,fu540-c000-i2c", "sifive,i2c0" + For Opencore based I2C IP block reimplemented in + FU540-C000 SoC. Please refer to sifive-blocks-ip-versioning.txt + for additional details. +- reg : bus address start and address range size of device +- clocks : handle to the controller clock; see the note below. + Mutually exclusive with opencores,ip-clock-frequency +- opencores,ip-clock-frequency: frequency of the controller clock in Hz; + see the note below. Mutually exclusive with clocks +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- interrupts : interrupt number. +- clock-frequency : frequency of bus clock in Hz; see the note below. + Defaults to 100 KHz when the property is not specified +- reg-shift : device register offsets are shifted by this value +- reg-io-width : io register width in bytes (1, 2 or 4) +- regstep : deprecated, use reg-shift above + +Note +clock-frequency property is meant to control the bus frequency for i2c bus +drivers, but it was incorrectly used to specify i2c controller input clock +frequency. So the following rules are set to fix this situation: +- if clock-frequency is present and neither opencores,ip-clock-frequency nor + clocks are, then clock-frequency specifies i2c controller clock frequency. + This is to keep backwards compatibility with setups using old DTB. i2c bus + frequency is fixed at 100 KHz. +- if clocks is present it specifies i2c controller clock. clock-frequency + property specifies i2c bus frequency. +- if opencores,ip-clock-frequency is present it specifies i2c controller + clock frequency. clock-frequency property specifies i2c bus frequency. + +Examples: + + i2c0: ocores@a0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "opencores,i2c-ocores"; + reg = <0xa0000000 0x8>; + interrupts = <10>; + opencores,ip-clock-frequency = <20000000>; + + reg-shift = <0>; /* 8 bit registers */ + reg-io-width = <1>; /* 8 bit read/write */ + + dummy@60 { + compatible = "dummy"; + reg = <0x60>; + }; + }; +or + i2c0: ocores@a0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "opencores,i2c-ocores"; + reg = <0xa0000000 0x8>; + interrupts = <10>; + clocks = <&osc>; + clock-frequency = <400000>; /* i2c bus frequency 400 KHz */ + + reg-shift = <0>; /* 8 bit registers */ + reg-io-width = <1>; /* 8 bit read/write */ + + dummy@60 { + compatible = "dummy"; + reg = <0x60>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-octeon.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt new file mode 100644 index 000000000..872d485df --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt @@ -0,0 +1,40 @@ +* Two Wire Serial Interface (TWSI) / I2C + +- compatible: "cavium,octeon-3860-twsi" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + + or + + compatible: "cavium,octeon-7890-twsi" + + Compatibility with cn78XX SOCs. + +- reg: The base address of the TWSI/I2C bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. I2C addresses have no size component. + +- interrupts: A single interrupt specifier. + +- clock-frequency: The I2C bus clock rate in Hz. + +Example: + twsi0: i2c@1180000001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cavium,octeon-3860-twsi"; + reg = <0x11800 0x00001000 0x0 0x200>; + interrupts = <0 45>; + clock-frequency = <100000>; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + }; + tmp@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-omap.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt new file mode 100644 index 000000000..a44573d7c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt @@ -0,0 +1,36 @@ +I2C for OMAP platforms + +Required properties : +- compatible : Must be + "ti,omap2420-i2c" for OMAP2420 SoCs + "ti,omap2430-i2c" for OMAP2430 SoCs + "ti,omap3-i2c" for OMAP3 SoCs + "ti,omap4-i2c" for OMAP4+ SoCs + "ti,am654-i2c", "ti,omap4-i2c" for AM654 SoCs + "ti,j721e-i2c", "ti,omap4-i2c" for J721E SoCs +- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based) +- #address-cells = <1>; +- #size-cells = <0>; + +Recommended properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise + the default 100 kHz frequency will be used. + +Optional properties: +- Child nodes conforming to i2c bus binding + +Note: Current implementation will fetch base address, irq and dma +from omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples : + +i2c1: i2c@0 { + compatible = "ti,omap3-i2c"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-opal.txt b/Documentation/devicetree/bindings/i2c/i2c-opal.txt new file mode 100644 index 000000000..12bc61465 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-opal.txt @@ -0,0 +1,37 @@ +Device-tree bindings for I2C OPAL driver +---------------------------------------- + +Most of the device node and properties layout is specific to the firmware and +used by the firmware itself for configuring the port. From the linux +perspective, the properties of use are "ibm,port-name" and "ibm,opal-id". + +Required properties: + +- reg: Port-id within a given master +- compatible: must be "ibm,opal-i2c" +- ibm,opal-id: Refers to a specific bus and used to identify it when calling + the relevant OPAL functions. +- bus-frequency: Operating frequency of the i2c bus (in HZ). Informational for + linux, used by the FW though. + +Optional properties: +- ibm,port-name: Firmware provides this name that uniquely identifies the i2c + port. + +The node contains a number of other properties that are used by the FW itself +and depend on the specific hardware implementation. The example below depicts +a P8 on-chip bus. + +Example: + +i2c-bus@0 { + reg = <0x0>; + bus-frequency = <0x61a80>; + compatible = "ibm,power8-i2c-port", "ibm,opal-i2c"; + ibm,opal-id = <0x1>; + ibm,port-name = "p8_00000000_e1p0"; + #address-cells = <0x1>; + phandle = <0x10000006>; + #size-cells = <0x0>; + linux,phandle = <0x10000006>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-owl.txt b/Documentation/devicetree/bindings/i2c/i2c-owl.txt new file mode 100644 index 000000000..54c05dbdb --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-owl.txt @@ -0,0 +1,29 @@ +Actions Semiconductor Owl I2C controller + +Required properties: + +- compatible : Should be one of the following: + - "actions,s700-i2c" for S700 SoC + - "actions,s900-i2c" for S900 SoC +- reg : Offset and length of the register set for the device. +- #address-cells : Should be 1. +- #size-cells : Should be 0. +- interrupts : A single interrupt specifier. +- clocks : Phandle of the clock feeding the I2C controller. + +Optional properties: + +- clock-frequency : Desired I2C bus clock frequency in Hz. As only Normal and + Fast modes are supported, possible values are 100000 and + 400000. +Examples: + + i2c0: i2c@e0170000 { + compatible = "actions,s900-i2c"; + reg = <0 0xe0170000 0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_I2C0>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt b/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt new file mode 100644 index 000000000..73a693d66 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt @@ -0,0 +1,27 @@ +* NXP PCA PCA9564/PCA9665 I2C controller + +The PCA9564/PCA9665 serves as an interface between most standard +parallel-bus microcontrollers/microprocessors and the serial I2C-bus +and allows the parallel bus system to communicate bi-directionally +with the I2C-bus. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : one of "nxp,pca9564" or "nxp,pca9665" + +Optional properties + - interrupts : the interrupt number + - reset-gpios : gpio specifier for gpio connected to RESET_N pin. As the line + is active low, it should be marked GPIO_ACTIVE_LOW. + - clock-frequency : I2C bus frequency. + +Example: + i2c0: i2c@80000 { + compatible = "nxp,pca9564"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x80000 0x4>; + reset-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pnx.txt b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt new file mode 100644 index 000000000..2a59006cf --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt @@ -0,0 +1,34 @@ +* NXP PNX I2C Controller + +Required properties: + + - reg: Offset and length of the register set for the device + - compatible: should be "nxp,pnx-i2c" + - interrupts: configure one interrupt line + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + +Optional properties: + + - clock-frequency: desired I2C bus clock frequency in Hz, Default: 100000 Hz + +Examples: + + i2c1: i2c@400a0000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400a0000 0x100>; + interrupt-parent = <&mic>; + interrupts = <51 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@400a8000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400a8000 0x100>; + interrupt-parent = <&mic>; + interrupts = <50 0>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt new file mode 100644 index 000000000..569b16248 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt @@ -0,0 +1,93 @@ +CE4100 I2C +---------- + +CE4100 has one PCI device which is described as the I2C-Controller. This +PCI device has three PCI-bars, each bar contains a complete I2C +controller. So we have a total of three independent I2C-Controllers +which share only an interrupt line. +The driver is probed via the PCI-ID and is gathering the information of +attached devices from the devices tree. +Grant Likely recommended to use the ranges property to map the PCI-Bar +number to its physical address and to use this to find the child nodes +of the specific I2C controller. This were his exact words: + + Here's where the magic happens. Each entry in + ranges describes how the parent pci address space + (middle group of 3) is translated to the local + address space (first group of 2) and the size of + each range (last cell). In this particular case, + the first cell of the local address is chosen to be + 1:1 mapped to the BARs, and the second is the + offset from be base of the BAR (which would be + non-zero if you had 2 or more devices mapped off + the same BAR) + + ranges allows the address mapping to be described + in a way that the OS can interpret without + requiring custom device driver code. + +This is an example which is used on FalconFalls: +------------------------------------------------ + i2c-controller@b,2 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "pci8086,2e68.2", + "pci8086,2e68", + "pciclass,ff0000", + "pciclass,ff00"; + + reg = <0x15a00 0x0 0x0 0x0 0x0>; + interrupts = <16 1>; + + /* as described by Grant, the first number in the group of + * three is the bar number followed by the 64bit bar address + * followed by size of the mapping. The bar address + * requires also a valid translation in parents ranges + * property. + */ + ranges = <0 0 0x02000000 0 0xdffe0500 0x100 + 1 0 0x02000000 0 0xdffe0600 0x100 + 2 0 0x02000000 0 0xdffe0700 0x100>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + + /* The first number in the reg property is the + * number of the bar + */ + reg = <0 0 0x100>; + + /* This I2C controller has no devices */ + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <1 0 0x100>; + + /* This I2C controller has one gpio controller */ + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <2 0 0x100>; + + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.yaml b/Documentation/devicetree/bindings/i2c/i2c-pxa.yaml new file mode 100644 index 000000000..015885dd0 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/i2c-pxa.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MMP I2C controller bindings + +maintainers: + - Rob Herring <robh+dt@kernel.org> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + - if: + not: + required: + - mrvl,i2c-polling + then: + required: + - interrupts + +properties: + compatible: + enum: + - mrvl,mmp-twsi + - mrvl,pxa-i2c + - marvell,armada-3700-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + + resets: + minItems: 1 + + mrvl,i2c-polling: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Disable interrupt of i2c controller. Polling status register of i2c + controller instead. + + mrvl,i2c-fast-mode: + $ref: /schemas/types.yaml#/definitions/flag + description: Enable fast mode of i2c controller. + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - '#address-cells' + - '#size-cells' + +examples: + - | + #include <dt-bindings/clock/marvell,mmp2.h> + i2c@d4011000 { + compatible = "mrvl,mmp-twsi"; + reg = <0xd4011000 0x1000>; + interrupts = <7>; + clocks = <&soc_clocks MMP2_CLK_TWSI1>; + mrvl,i2c-fast-mode; + #address-cells = <1>; + #size-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt b/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt new file mode 100644 index 000000000..c6668b7c6 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt @@ -0,0 +1,92 @@ +Qualcomm Camera Control Interface (CCI) I2C controller + +PROPERTIES: + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,msm8916-cci" + "qcom,msm8996-cci" + "qcom,sdm845-cci" + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: base address CCI I2C controller and length of memory + mapped region. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: specifies the CCI I2C interrupt. The format of the + specifier is defined by the binding document describing + the node's interrupt parent. + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: a list of phandle, should contain an entry for each + entries in clock-names. + +- clock-names + Usage: required + Value type: <string> + Definition: a list of clock names, must include "cci" clock. + +- power-domains + Usage: required for "qcom,msm8996-cci" + Value type: <prop-encoded-array> + Definition: + +SUBNODES: + +The CCI provides I2C masters for one (msm8916) or two i2c busses (msm8996 and +sdm845), described as subdevices named "i2c-bus@0" and "i2c-bus@1". + +PROPERTIES: + +- reg: + Usage: required + Value type: <u32> + Definition: Index of the CCI bus/master + +- clock-frequency: + Usage: optional + Value type: <u32> + Definition: Desired I2C bus clock frequency in Hz, defaults to 100 + kHz if omitted. + +Example: + + cci@a0c000 { + compatible = "qcom,msm8996-cci"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xa0c000 0x1000>; + interrupts = <GIC_SPI 295 IRQ_TYPE_EDGE_RISING>; + clocks = <&mmcc MMSS_MMAGIC_AHB_CLK>, + <&mmcc CAMSS_TOP_AHB_CLK>, + <&mmcc CAMSS_CCI_AHB_CLK>, + <&mmcc CAMSS_CCI_CLK>, + <&mmcc CAMSS_AHB_CLK>; + clock-names = "mmss_mmagic_ahb", + "camss_top_ahb", + "cci_ahb", + "cci", + "camss_ahb"; + + i2c-bus@0 { + reg = <0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c-bus@1 { + reg = <1>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml b/Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml new file mode 100644 index 000000000..7f254d795 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml @@ -0,0 +1,138 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/i2c-rk3x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip RK3xxx I2C controller + +description: + This driver interfaces with the native I2C controller present in Rockchip + RK3xxx SoCs. + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +# Everything else is described in the common file +properties: + compatible: + oneOf: + - const: rockchip,rv1108-i2c + - const: rockchip,rk3066-i2c + - const: rockchip,rk3188-i2c + - const: rockchip,rk3228-i2c + - const: rockchip,rk3288-i2c + - const: rockchip,rk3399-i2c + - items: + - enum: + - rockchip,rk3036-i2c + - rockchip,rk3368-i2c + - const: rockchip,rk3288-i2c + - items: + - enum: + - rockchip,px30-i2c + - rockchip,rk3308-i2c + - rockchip,rk3328-i2c + - const: rockchip,rk3399-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: + For older hardware (rk3066, rk3188, rk3228, rk3288) + there is one clock that is used both to derive the functional clock + for the device and as the bus clock. + For newer hardware (rk3399) this clock is used to derive + the functional clock + - description: + For newer hardware (rk3399) this is the bus clock + + clock-names: + minItems: 1 + items: + - const: i2c + - const: pclk + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Required on RK3066, RK3188 the phandle of the syscon node for + the general register file (GRF) + On those SoCs an alias with the correct I2C bus ID + (bit offset in the GRF) is also required. + + clock-frequency: + default: 100000 + description: + SCL frequency to use (in Hz). If omitted, 100kHz is used. + + i2c-scl-rising-time-ns: + default: 1000 + description: + Number of nanoseconds the SCL signal takes to rise + (t(r) in I2C specification). If not specified this is assumed to be + the maximum the specification allows(1000 ns for Standard-mode, + 300 ns for Fast-mode) which might cause slightly slower communication. + + i2c-scl-falling-time-ns: + default: 300 + description: + Number of nanoseconds the SCL signal takes to fall + (t(f) in the I2C specification). If not specified this is assumed to + be the maximum the specification allows (300 ns) which might cause + slightly slower communication. + + i2c-sda-falling-time-ns: + default: 300 + description: + Number of nanoseconds the SDA signal takes to fall + (t(f) in the I2C specification). If not specified we will use the SCL + value since they are the same in nearly all cases. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +if: + properties: + compatible: + contains: + enum: + - rockchip,rk3066-i2c + - rockchip,rk3188-i2c + +then: + required: + - rockchip,grf + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3188-cru-common.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c0: i2c@2002d000 { + compatible = "rockchip,rk3188-i2c"; + reg = <0x2002d000 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_I2C0>; + clock-names = "i2c"; + rockchip,grf = <&grf>; + i2c-scl-falling-time-ns = <100>; + i2c-scl-rising-time-ns = <800>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt new file mode 100644 index 000000000..66ae46d3b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -0,0 +1,58 @@ +* Samsung's I2C controller + +The Samsung's I2C controller is used to interface with I2C devices. + +Required properties: + - compatible: value should be either of the following. + (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c. + (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. + (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used + inside HDMIPHY block found on several samsung SoCs + (d) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as + a host to SATA PHY controller on an internal bus. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. + +Required for all cases except "samsung,s3c2440-hdmiphy-i2c": + - Samsung GPIO variant (deprecated): + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. Required in all + cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output + lines are permanently wired to the respective clienta + - Pinctrl variant (preferred, if available): + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - samsung,i2c-slave-addr: Slave address in multi-master environment. If not + specified, default value is 0. + - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not + specified, the default value in Hz is 100000. + - samsung,sysreg-phandle - handle to syscon used to control the system registers + +Example: + + i2c@13870000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x13870000 0x100>; + interrupts = <345>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <100000>; + /* Samsung GPIO variant begins here */ + gpios = <&gpd1 2 0 /* SDA */ + &gpd1 3 0 /* SCL */>; + /* Samsung GPIO variant ends here */ + /* Pinctrl variant begins here */ + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + /* Pinctrl variant ends here */ + #address-cells = <1>; + #size-cells = <0>; + + wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sirf.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt new file mode 100644 index 000000000..2701eefb0 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt @@ -0,0 +1,19 @@ +I2C for SiRFprimaII platforms + +Required properties : +- compatible : Must be "sirf,prima2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the property indicates the default frequency 100 kHz. + +Examples : + +i2c0: i2c@b00e0000 { + compatible = "sirf,prima2-i2c"; + reg = <0xb00e0000 0x10000>; + interrupts = <24>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sprd.txt b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt new file mode 100644 index 000000000..60b7cda15 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt @@ -0,0 +1,31 @@ +I2C for Spreadtrum platforms + +Required properties: +- compatible: Should be "sprd,sc9860-i2c". +- reg: Specify the physical base address of the controller and length + of memory mapped region. +- interrupts: Should contain I2C interrupt. +- clock-names: Should contain following entries: + "i2c" for I2C clock, + "source" for I2C source (parent) clock, + "enable" for I2C module enable clock. +- clocks: Should contain a clock specifier for each entry in clock-names. +- clock-frequency: Constains desired I2C bus clock frequency in Hz. +- #address-cells: Should be 1 to describe address cells for I2C device address. +- #size-cells: Should be 0 means no size cell for I2C device address. + +Optional properties: +- Child nodes conforming to I2C bus binding + +Examples: +i2c0: i2c@70500000 { + compatible = "sprd,sc9860-i2c"; + reg = <0 0x70500000 0 0x1000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "i2c", "source", "enable"; + clocks = <&clk_i2c3>, <&ext_26m>, <&clk_ap_apb_gates 11>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt new file mode 100644 index 000000000..4c26fda38 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -0,0 +1,41 @@ +ST SSC binding, for I2C mode operation + +Required properties : +- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- clock-names: Must contain "ssc". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. +- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is + allowed through the deglitch circuit. In units of us. +- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is + allowed through the deglitch circuit. In units of us. +- A pinctrl state named "idle" could be defined to set pins in idle state + when I2C instance is not performing a transfer. +- A pinctrl state named "sleep" could be defined to set pins in sleep state + when driver enters in suspend. + + + +Example : + +i2c0: i2c@fed40000 { + compatible = "st,comms-ssc4-i2c"; + reg = <0xfed40000 0x110>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; + clock-names = "ssc"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0_default>; + st,i2c-min-scl-pulse-width-us = <0>; + st,i2c-min-sda-pulse-width-us = <5>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-stu300.txt b/Documentation/devicetree/bindings/i2c/i2c-stu300.txt new file mode 100644 index 000000000..bd81a4826 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-stu300.txt @@ -0,0 +1,15 @@ +ST Microelectronics DDC I2C + +Required properties : +- compatible : Must be "st,ddci2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding + +Examples : + diff --git a/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt new file mode 100644 index 000000000..72f4a2f0f --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt @@ -0,0 +1,29 @@ +Socionext SynQuacer I2C + +Required properties: +- compatible : Must be "socionext,synquacer-i2c" +- reg : Offset and length of the register set for the device +- interrupts : A single interrupt specifier +- #address-cells : Must be <1>; +- #size-cells : Must be <0>; +- clock-names : Must contain "pclk". +- clocks : Must contain an entry for each name in clock-names. + (See the common clock bindings.) + +Optional properties: +- clock-frequency : Desired I2C bus clock frequency in Hz. As only Normal and + Fast modes are supported, possible values are 100000 and + 400000. + +Example : + + i2c@51210000 { + compatible = "socionext,synquacer-i2c"; + reg = <0x51210000 0x1000>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "pclk"; + clocks = <&clk_i2c>; + clock-frequency = <400000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-versatile.txt b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt new file mode 100644 index 000000000..361d31c51 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt @@ -0,0 +1,10 @@ +i2c Controller on ARM Versatile platform: + +Required properties: +- compatible : Must be "arm,versatile-i2c"; +- reg +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding diff --git a/Documentation/devicetree/bindings/i2c/i2c-wmt.txt b/Documentation/devicetree/bindings/i2c/i2c-wmt.txt new file mode 100644 index 000000000..94a425eaa --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-wmt.txt @@ -0,0 +1,24 @@ +* Wondermedia I2C Controller + +Required properties : + + - compatible : should be "wm,wm8505-i2c" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number + - clocks : phandle to the I2C clock source + +Optional properties : + + - clock-frequency : desired I2C bus clock frequency in Hz. + Valid values are 100000 and 400000. + Default to 100000 if not specified, or invalid value. + +Example : + + i2c_0: i2c@d8280000 { + compatible = "wm,wm8505-i2c"; + reg = <0xd8280000 0x1000>; + interrupts = <19>; + clocks = <&clki2c0>; + clock-frequency = <400000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt b/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt new file mode 100644 index 000000000..f6b2c20cf --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt @@ -0,0 +1,15 @@ +APM X-Gene SLIMpro Mailbox I2C Driver + +An I2C controller accessed over the "SLIMpro" mailbox. + +Required properties : + + - compatible : should be "apm,xgene-slimpro-i2c" + - mboxes : use the label reference for the mailbox as the first parameter. + The second parameter is the channel number. + +Example : + i2cslimpro { + compatible = "apm,xgene-slimpro-i2c"; + mboxes = <&mailbox 0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt new file mode 100644 index 000000000..f818ef507 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt @@ -0,0 +1,22 @@ +Device tree configuration for the I2C controller on the XLP9xx/5xx SoC + +Required properties: +- compatible : should be "netlogic,xlp980-i2c" +- reg : bus address start and address range size of device +- interrupts : interrupt number + +Optional properties: +- clock-frequency : frequency of bus clock in Hz + Defaults to 100 KHz when the property is not specified + +Example: + +i2c0: i2c@113100 { + compatible = "netlogic,xlp980-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x113100 0x100>; + clock-frequency = <400000>; + interrupts = <30>; + interrupt-parent = <&pic>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt b/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt new file mode 100644 index 000000000..cb806d1ae --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt @@ -0,0 +1,22 @@ +ZTE zx2967 I2C controller + +Required properties: + - compatible: must be "zte,zx296718-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + - clock-frequency: the desired I2C bus clock frequency. + +Examples: + + i2c@112000 { + compatible = "zte,zx296718-i2c"; + reg = <0x00112000 0x1000>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&osc24m>; + #address-cells = <1> + #size-cells = <0>; + clock-frequency = <1600000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt new file mode 100644 index 000000000..df41f72af --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -0,0 +1,144 @@ +Generic device tree bindings for I2C busses +=========================================== + +This document describes generic bindings which can be used to describe I2C +busses and their child devices in a device tree. + +Required properties (per bus) +----------------------------- + +- #address-cells - should be <1>. Read more about addresses below. +- #size-cells - should be <0>. +- compatible - name of I2C bus controller + +For other required properties e.g. to describe register sets, +clocks, etc. check the binding documentation of the specific driver. + +The cells properties above define that an address of children of an I2C bus +are described by a single value. + +Optional properties (per bus) +----------------------------- + +These properties may not be supported by all drivers. However, if a driver +wants to support one of the below features, it should adapt these bindings. + +- clock-frequency + frequency of bus clock in Hz. + +- i2c-bus + For I2C adapters that have child nodes that are a mixture of both I2C + devices and non-I2C devices, the 'i2c-bus' subnode can be used for + populating I2C devices. If the 'i2c-bus' subnode is present, only + subnodes of this will be considered as I2C slaves. The properties, + '#address-cells' and '#size-cells' must be defined under this subnode + if present. + +- i2c-scl-falling-time-ns + Number of nanoseconds the SCL signal takes to fall; t(f) in the I2C + specification. + +- i2c-scl-internal-delay-ns + Number of nanoseconds the IP core additionally needs to setup SCL. + +- i2c-scl-rising-time-ns + Number of nanoseconds the SCL signal takes to rise; t(r) in the I2C + specification. + +- i2c-sda-falling-time-ns + Number of nanoseconds the SDA signal takes to fall; t(f) in the I2C + specification. + +- i2c-analog-filter + Enable analog filter for i2c lines. + +- i2c-digital-filter + Enable digital filter for i2c lines. + +- i2c-digital-filter-width-ns + Width of spikes which can be filtered by digital filter + (i2c-digital-filter). This width is specified in nanoseconds. + +- i2c-analog-filter-cutoff-frequency + Frequency that the analog filter (i2c-analog-filter) uses to distinguish + which signal to filter. Signal with higher frequency than specified will + be filtered out. Only lower frequency will pass (this is applicable to + a low-pass analog filter). Typical value should be above the normal + i2c bus clock frequency (clock-frequency). + Specified in Hz. + +- multi-master + states that there is another master active on this bus. The OS can use + this information to adapt power management to keep the arbitration awake + all the time, for example. Can not be combined with 'single-master'. + +- pinctrl + add extra pinctrl to configure SCL/SDA pins to GPIO function for bus + recovery, call it "gpio" or "recovery" (deprecated) state + +- scl-gpios + specify the gpio related to SCL pin. Used for GPIO bus recovery. + +- sda-gpios + specify the gpio related to SDA pin. Optional for GPIO bus recovery. + +- single-master + states that there is no other master active on this bus. The OS can use + this information to detect a stalled bus more reliably, for example. + Can not be combined with 'multi-master'. + +- smbus + states that additional SMBus restrictions and features apply to this bus. + Examples of features are SMBusHostNotify and SMBusAlert. Examples of + restrictions are more reserved addresses and timeout definitions. + +Required properties (per child device) +-------------------------------------- + +- compatible + name of I2C slave device + +- reg + One or many I2C slave addresses. These are usually a 7 bit addresses. + However, flags can be attached to an address. I2C_TEN_BIT_ADDRESS is + used to mark a 10 bit address. It is needed to avoid the ambiguity + between e.g. a 7 bit address of 0x50 and a 10 bit address of 0x050 + which, in theory, can be on the same bus. + Another flag is I2C_OWN_SLAVE_ADDRESS to mark addresses on which we + listen to be devices ourselves. + +Optional properties (per child device) +-------------------------------------- + +These properties may not be supported by all drivers. However, if a driver +wants to support one of the below features, it should adapt these bindings. + +- host-notify + device uses SMBus host notify protocol instead of interrupt line. + +- interrupts + interrupts used by the device. + +- interrupt-names + "irq", "wakeup" and "smbus_alert" names are recognized by I2C core, + other names are left to individual drivers. + +- reg-names + Names of map programmable addresses. + It can contain any map needing another address than default one. + +- wakeup-source + device can be used as a wakeup source. + +Binding may contain optional "interrupts" property, describing interrupts +used by the device. I2C core will assign "irq" interrupt (or the very first +interrupt if not using interrupt names) as primary interrupt for the slave. + +Alternatively, devices supporting SMBus Host Notify, and connected to +adapters that support this feature, may use "host-notify" property. I2C +core will create a virtual interrupt for Host Notify and assign it as +primary interrupt for the slave. + +Also, if device is marked as a wakeup source, I2C core will set up "wakeup" +interrupt for the device. If "wakeup" interrupt name is not present in the +binding, then primary interrupt will be used as wakeup interrupt. diff --git a/Documentation/devicetree/bindings/i2c/ibm,p8-occ-hwmon.txt b/Documentation/devicetree/bindings/i2c/ibm,p8-occ-hwmon.txt new file mode 100644 index 000000000..5dc5d2e25 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ibm,p8-occ-hwmon.txt @@ -0,0 +1,25 @@ +Device-tree bindings for I2C-based On-Chip Controller hwmon device +------------------------------------------------------------------ + +Required properties: + - compatible = "ibm,p8-occ-hwmon"; + - reg = <I2C address>; : I2C bus address + +Examples: + + i2c-bus@100 { + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + < more properties > + + occ-hwmon@1 { + compatible = "ibm,p8-occ-hwmon"; + reg = <0x50>; + }; + + occ-hwmon@2 { + compatible = "ibm,p8-occ-hwmon"; + reg = <0x51>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/ingenic,i2c.yaml b/Documentation/devicetree/bindings/i2c/ingenic,i2c.yaml new file mode 100644 index 000000000..e1e65eb4f --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ingenic,i2c.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/ingenic,i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic SoCs I2C controller devicetree bindings + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + $nodename: + pattern: "^i2c@[0-9a-f]+$" + + compatible: + oneOf: + - enum: + - ingenic,jz4770-i2c + - ingenic,x1000-i2c + - items: + - const: ingenic,jz4780-i2c + - const: ingenic,jz4770-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-frequency: + enum: [ 100000, 400000 ] + + dmas: + items: + - description: DMA controller phandle and request line for RX + - description: DMA controller phandle and request line for TX + + dma-names: + items: + - const: rx + - const: tx + +required: + - compatible + - reg + - interrupts + - clocks + - clock-frequency + - dmas + - dma-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/jz4780-cgu.h> + #include <dt-bindings/dma/jz4780-dma.h> + #include <dt-bindings/interrupt-controller/irq.h> + i2c@10054000 { + compatible = "ingenic,jz4780-i2c", "ingenic,jz4770-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10054000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <56>; + + clocks = <&cgu JZ4780_CLK_SMB4>; + pinctrl-names = "default"; + pinctrl-0 = <&pins_i2c4_data>; + + dmas = <&dma JZ4780_DMA_SMB4_RX 0xffffffff>, + <&dma JZ4780_DMA_SMB4_TX 0xffffffff>; + dma-names = "rx", "tx"; + + clock-frequency = <400000>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + + interrupt-parent = <&gpf>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml new file mode 100644 index 000000000..5b5ae402f --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/marvell,mv64xxx-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MV64XXX I2C Controller Device Tree Bindings + +maintainers: + - Gregory CLEMENT <gregory.clement@bootlin.com> + +properties: + compatible: + oneOf: + - const: allwinner,sun4i-a10-i2c + - items: + - const: allwinner,sun7i-a20-i2c + - const: allwinner,sun4i-a10-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun8i-a23-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun8i-a83t-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun50i-a64-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun50i-a100-i2c + - const: allwinner,sun6i-a31-i2c + - items: + - const: allwinner,sun50i-h6-i2c + - const: allwinner,sun6i-a31-i2c + + - const: marvell,mv64xxx-i2c + - const: marvell,mv78230-i2c + - const: marvell,mv78230-a0-i2c + + description: + Only use "marvell,mv78230-a0-i2c" for a very rare, initial + version of the SoC which had broken offload support. Linux + auto-detects this and sets it appropriately. + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + items: + - description: Reference clock for the I2C bus + - description: Bus clock (Only for Armada 7K/8K) + + clock-names: + minItems: 1 + maxItems: 2 + items: + - const: core + - const: reg + description: + Mandatory if two clocks are used (only for Armada 7k and 8k). + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun4i-a10-i2c + - allwinner,sun6i-a31-i2c + + then: + required: + - clocks + + - if: + properties: + compatible: + contains: + const: allwinner,sun6i-a31-i2c + + then: + required: + - resets + +unevaluatedProperties: false + +examples: + - | + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; + + - | + i2c@11000 { + compatible = "marvell,mv78230-i2c"; + reg = <0x11000 0x100>; + interrupts = <29>; + clock-frequency = <100000>; + }; + + - | + i2c@701000 { + compatible = "marvell,mv78230-i2c"; + reg = <0x701000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + clock-names = "core", "reg"; + clocks = <&core_clock>, <®_clock>; + }; + +... diff --git a/Documentation/devicetree/bindings/i2c/mellanox,i2c-mlxbf.txt b/Documentation/devicetree/bindings/i2c/mellanox,i2c-mlxbf.txt new file mode 100644 index 000000000..566ea861a --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/mellanox,i2c-mlxbf.txt @@ -0,0 +1,42 @@ +Device tree configuration for the Mellanox I2C SMBus on BlueField SoCs + +Required Properties: + +- compatible : should be "mellanox,i2c-mlxbf1" or "mellanox,i2c-mlxbf2". + +- reg : address offset and length of the device registers. The + registers consist of the following set of resources: + 1) Smbus block registers. + 2) Cause master registers. + 3) Cause slave registers. + 4) Cause coalesce registers (if compatible isn't set + to "mellanox,i2c-mlxbf1"). + +- interrupts : interrupt number. + +Optional Properties: + +- clock-frequency : bus frequency used to configure timing registers; + allowed values are 100000, 400000 and 1000000; + those are expressed in Hz. Default is 100000. + +Example: + +i2c@2804000 { + compatible = "mellanox,i2c-mlxbf1"; + reg = <0x02804000 0x800>, + <0x02801200 0x020>, + <0x02801260 0x020>; + interrupts = <57>; + clock-frequency = <100000>; +}; + +i2c@2808800 { + compatible = "mellanox,i2c-mlxbf2"; + reg = <0x02808800 0x600>, + <0x02808e00 0x020>, + <0x02808e20 0x020>, + <0x02808e40 0x010>; + interrupts = <57>; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml b/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml new file mode 100644 index 000000000..e3ef2d36f --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/nuvoton,npcm7xx-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: nuvoton NPCM7XX I2C Controller Device Tree Bindings + +description: | + The NPCM750x includes sixteen I2C bus controllers. All Controllers support + both master and slave mode. Each controller can switch between master and slave + at run time (i.e. IPMB mode). Each controller has two 16 byte HW FIFO for TX and + RX. + +maintainers: + - Tali Perry <tali.perry1@gmail.com> + +properties: + compatible: + const: nuvoton,npcm7xx-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: Reference clock for the I2C bus + + clock-frequency: + description: Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. + possible values are 100000, 400000 and 1000000. + default: 100000 + enum: [100000, 400000, 1000000] + +required: + - compatible + - reg + - interrupts + - clocks + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/nuvoton,npcm7xx-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + i2c0: i2c@80000 { + reg = <0x80000 0x1000>; + clocks = <&clk NPCM7XX_CLK_APB2>; + clock-frequency = <100000>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + compatible = "nuvoton,npcm750-i2c"; + }; + +... diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt new file mode 100644 index 000000000..ab240e10d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt @@ -0,0 +1,42 @@ +NVIDIA Tegra186 BPMP I2C controller + +In Tegra186, the BPMP (Boot and Power Management Processor) owns certain HW +devices, such as the I2C controller for the power management I2C bus. Software +running on other CPUs must perform IPC to the BPMP in order to execute +transactions on that I2C bus. This binding describes an I2C bus that is +accessed in such a fashion. + +The BPMP I2C node must be located directly inside the main BPMP node. See +../firmware/nvidia,tegra186-bpmp.txt for details of the BPMP binding. + +This node represents an I2C controller. See ../i2c/i2c.txt for details of the +core I2C binding. + +Required properties: +- compatible: + Array of strings. + One of: + - "nvidia,tegra186-bpmp-i2c". +- #address-cells: Address cells for I2C device address. + Single-cell integer. + Must be <1>. +- #size-cells: + Single-cell integer. + Must be <0>. +- nvidia,bpmp-bus-id: + Single-cell integer. + Indicates the I2C bus number this DT node represent, as defined by the + BPMP firmware. + +Example: + +bpmp { + ... + + i2c { + compatible = "nvidia,tegra186-bpmp-i2c"; + #address-cells = <1>; + #size-cells = <0>; + nvidia,bpmp-bus-id = <5>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt new file mode 100644 index 000000000..3f2f990c2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt @@ -0,0 +1,87 @@ +NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver. + +Required properties: +- compatible : For Tegra20, must be one of "nvidia,tegra20-i2c-dvc" or + "nvidia,tegra20-i2c". For Tegra30, must be "nvidia,tegra30-i2c". + For Tegra114, must be "nvidia,tegra114-i2c". Otherwise, must be + "nvidia,<chip>-i2c", plus at least one of the above, where <chip> is + tegra124, tegra132, or tegra210. + Details of compatible are as follows: + nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C + controller. This only support master mode of I2C communication. Register + interface/offset and interrupts handling are different than generic I2C + controller. Driver of DVC I2C controller is only compatible with + "nvidia,tegra20-i2c-dvc". + nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support + master and slave mode of I2C communication. The i2c-tegra driver only + support master mode of I2C communication. Driver of I2C controller is + only compatible with "nvidia,tegra20-i2c". + nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is + very much similar to Tegra20 I2C controller with additional feature: + Continue Transfer Support. This feature helps to implement M_NO_START + as per I2C core API transfer flags. Driver of I2C controller is + compatible with "nvidia,tegra30-i2c" to enable the continue transfer + support. This is also compatible with "nvidia,tegra20-i2c" without + continue transfer support. + nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is + very much similar to Tegra30 I2C controller with some hardware + modification: + - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and + fast-clk. Tegra114 has only one clock source called as div-clk and + hence clock mechanism is changed in I2C controller. + - Tegra30/Tegra20 I2C controller has enabled per packet transfer by + default and there is no way to disable it. Tegra114 has this + interrupt disable by default and SW need to enable explicitly. + Due to above changes, Tegra114 I2C driver makes incompatible with + previous hardware driver. Hence, tegra114 I2C controller is compatible + with "nvidia,tegra114-i2c". + nvidia,tegra210-i2c-vi: Tegra210 has one I2C controller that is on host1x bus + and is part of VE power domain and typically used for camera use-cases. + This VI I2C controller is mostly compatible with the programming model + of the regular I2C controllers with a few exceptions. The I2C registers + start at an offset of 0xc00 (instead of 0), registers are 16 bytes + apart (rather than 4) and the controller does not support slave mode. +- reg: Should contain I2C controller registers physical address and length. +- interrupts: Should contain I2C controller interrupts. +- address-cells: Address cells for I2C device address. +- size-cells: Size of the I2C device address. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + Tegra20/Tegra30: + - div-clk + - fast-clk + Tegra114: + - div-clk + Tegra210: + - div-clk + - slow (only for nvidia,tegra210-i2c-vi compatible node) +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - i2c +- power-domains: Only for nvidia,tegra210-i2c-vi compatible node and must + include venc powergate node as vi i2c is part of VE power domain. + tegra210-i2c-vi: + - pd_venc +- dmas: Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names: Must include the following entries: + - rx + - tx + +Example: + + i2c@7000c000 { + compatible = "nvidia,tegra20-i2c"; + reg = <0x7000c000 0x100>; + interrupts = <0 38 0x04>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&tegra_car 12>, <&tegra_car 124>; + clock-names = "div-clk", "fast-clk"; + resets = <&tegra_car 12>; + reset-names = "i2c"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/i2c/nxp,pca9541.txt b/Documentation/devicetree/bindings/i2c/nxp,pca9541.txt new file mode 100644 index 000000000..42bfc09c8 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nxp,pca9541.txt @@ -0,0 +1,29 @@ +* NXP PCA9541 I2C bus master selector + +Required Properties: + + - compatible: Must be "nxp,pca9541" + + - reg: The I2C address of the device. + + The following required properties are defined externally: + + - I2C arbitration bus node. See i2c-arb.txt in this directory. + + +Example: + + i2c-arbitrator@74 { + compatible = "nxp,pca9541"; + reg = <0x74>; + + i2c-arb { + #address-cells = <1>; + #size-cells = <0>; + + eeprom@54 { + compatible = "atmel,24c08"; + reg = <0x54>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt new file mode 100644 index 000000000..dc71754a5 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt @@ -0,0 +1,40 @@ +Qualcomm Universal Peripheral (QUP) I2C controller + +Required properties: + - compatible: Should be: + * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064. + * "qcom,i2c-qup-v2.1.1" for 8974 v1. + * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later. + - reg: Should contain QUP register address and length. + - interrupts: Should contain I2C interrupt. + + - clocks: A list of phandles + clock-specifiers, one for each entry in + clock-names. + - clock-names: Should contain: + * "core" for the core clock + * "iface" for the AHB clock + + - #address-cells: Should be <1> Address cells for i2c device address + - #size-cells: Should be <0> as i2c addresses have no size component + +Optional properties: + - clock-frequency: Should specify the desired i2c bus clock frequency in Hz, + defaults to 100kHz if omitted. + +Child nodes should conform to i2c bus binding. + +Example: + + i2c@f9924000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9924000 0x1000>; + interrupts = <0 96 0>; + + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + + clock-frequency = <355000>; + + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/renesas,i2c.txt b/Documentation/devicetree/bindings/i2c/renesas,i2c.txt new file mode 100644 index 000000000..96d869ac3 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/renesas,i2c.txt @@ -0,0 +1,66 @@ +I2C for R-Car platforms + +Required properties: +- compatible: + "renesas,i2c-r8a7742" if the device is a part of a R8A7742 SoC. + "renesas,i2c-r8a7743" if the device is a part of a R8A7743 SoC. + "renesas,i2c-r8a7744" if the device is a part of a R8A7744 SoC. + "renesas,i2c-r8a7745" if the device is a part of a R8A7745 SoC. + "renesas,i2c-r8a77470" if the device is a part of a R8A77470 SoC. + "renesas,i2c-r8a774a1" if the device is a part of a R8A774A1 SoC. + "renesas,i2c-r8a774b1" if the device is a part of a R8A774B1 SoC. + "renesas,i2c-r8a774c0" if the device is a part of a R8A774C0 SoC. + "renesas,i2c-r8a774e1" if the device is a part of a R8A774E1 SoC. + "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. + "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. + "renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC. + "renesas,i2c-r8a7791" if the device is a part of a R8A7791 SoC. + "renesas,i2c-r8a7792" if the device is a part of a R8A7792 SoC. + "renesas,i2c-r8a7793" if the device is a part of a R8A7793 SoC. + "renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC. + "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. + "renesas,i2c-r8a7796" if the device is a part of a R8A77960 SoC. + "renesas,i2c-r8a77961" if the device is a part of a R8A77961 SoC. + "renesas,i2c-r8a77965" if the device is a part of a R8A77965 SoC. + "renesas,i2c-r8a77970" if the device is a part of a R8A77970 SoC. + "renesas,i2c-r8a77980" if the device is a part of a R8A77980 SoC. + "renesas,i2c-r8a77990" if the device is a part of a R8A77990 SoC. + "renesas,i2c-r8a77995" if the device is a part of a R8A77995 SoC. + "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. + "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible + device. + "renesas,rcar-gen3-i2c" for a generic R-Car Gen3 or RZ/G2 compatible + device. + "renesas,i2c-rcar" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed + by the generic version. + +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt specifier. + +Optional properties: +- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this + property indicates the default frequency 100 kHz. +- clocks: clock specifier. +- dmas: Must contain a list of two references to DMA specifiers, one for + transmission, and one for reception. +- dma-names: Must contain a list of two DMA names, "tx" and "rx". + +- i2c-scl-falling-time-ns: see i2c.txt +- i2c-scl-internal-delay-ns: see i2c.txt +- i2c-scl-rising-time-ns: see i2c.txt + +Examples : + +i2c0: i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c"; + reg = <0 0xe6508000 0 0x40>; + interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C0>; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/renesas,iic-emev2.txt b/Documentation/devicetree/bindings/i2c/renesas,iic-emev2.txt new file mode 100644 index 000000000..5ed1ea1c7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/renesas,iic-emev2.txt @@ -0,0 +1,22 @@ +Device tree configuration for Renesas EMEV2 IIC controller + +Required properties: +- compatible : "renesas,iic-emev2" +- reg : address start and address range size of device +- interrupts : specifier for the IIC controller interrupt +- clocks : phandle to the IP core SCLK +- clock-names : must be "sclk" +- #address-cells : should be <1> +- #size-cells : should be <0> + +Example: + + iic0: i2c@e0070000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,iic-emev2"; + reg = <0xe0070000 0x28>; + interrupts = <0 32 IRQ_TYPE_EDGE_RISING>; + clocks = <&iic0_sclk>; + clock-names = "sclk"; + }; diff --git a/Documentation/devicetree/bindings/i2c/renesas,iic.txt b/Documentation/devicetree/bindings/i2c/renesas,iic.txt new file mode 100644 index 000000000..93d412832 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/renesas,iic.txt @@ -0,0 +1,72 @@ +Device tree configuration for Renesas IIC (sh_mobile) driver + +Required properties: +- compatible : + - "renesas,iic-r8a73a4" (R-Mobile APE6) + - "renesas,iic-r8a7740" (R-Mobile A1) + - "renesas,iic-r8a7742" (RZ/G1H) + - "renesas,iic-r8a7743" (RZ/G1M) + - "renesas,iic-r8a7744" (RZ/G1N) + - "renesas,iic-r8a7745" (RZ/G1E) + - "renesas,iic-r8a774a1" (RZ/G2M) + - "renesas,iic-r8a774b1" (RZ/G2N) + - "renesas,iic-r8a774c0" (RZ/G2E) + - "renesas,iic-r8a774e1" (RZ/G2H) + - "renesas,iic-r8a7790" (R-Car H2) + - "renesas,iic-r8a7791" (R-Car M2-W) + - "renesas,iic-r8a7792" (R-Car V2H) + - "renesas,iic-r8a7793" (R-Car M2-N) + - "renesas,iic-r8a7794" (R-Car E2) + - "renesas,iic-r8a7795" (R-Car H3) + - "renesas,iic-r8a7796" (R-Car M3-W) + - "renesas,iic-r8a77961" (R-Car M3-W+) + - "renesas,iic-r8a77965" (R-Car M3-N) + - "renesas,iic-r8a77990" (R-Car E3) + - "renesas,iic-sh73a0" (SH-Mobile AG5) + - "renesas,rcar-gen2-iic" (generic R-Car Gen2 or RZ/G1 + compatible device) + - "renesas,rcar-gen3-iic" (generic R-Car Gen3 or RZ/G2 + compatible device) + - "renesas,rmobile-iic" (generic device) + + When compatible with a generic R-Car version, nodes + must list the SoC-specific version corresponding to + the platform first followed by the generic R-Car + version. + + When compatible with "renesas,rmobile-iic" it should + be the last compatibility string listed. + + The r8a77990 (R-Car E3) and r8a774c0 (RZ/G2E) + controllers are not considered compatible with + "renesas,rcar-gen3-iic" or "renesas,rmobile-iic" + due to the absence of automatic transmission registers. + +- reg : address start and address range size of device +- interrupts : interrupt of device +- clocks : clock for device +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset. +- dmas : Must contain a list of two references to DMA + specifiers, one for transmission, and one for + reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". + + +Pinctrl properties might be needed, too. See there. + +Example: + + iic0: i2c@e6500000 { + compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic", + "renesas,rmobile-iic"; + reg = <0 0xe6500000 0 0x425>; + interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7790_CLK_IIC0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/renesas,riic.txt b/Documentation/devicetree/bindings/i2c/renesas,riic.txt new file mode 100644 index 000000000..e26fe3ad8 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/renesas,riic.txt @@ -0,0 +1,32 @@ +Device tree configuration for Renesas RIIC driver + +Required properties: +- compatible : + "renesas,riic-r7s72100" if the device is a part of a R7S72100 SoC. + "renesas,riic-r7s9210" if the device is a part of a R7S9210 SoC. + "renesas,riic-rz" for a generic RZ/A compatible device. +- reg : address start and address range size of device +- interrupts : 8 interrupts (TEI, RI, TI, SPI, STI, NAKI, ALI, TMOI) +- clock-frequency : frequency of bus clock in Hz +- #address-cells : should be <1> +- #size-cells : should be <0> + +Pinctrl properties might be needed, too. See there. + +Example: + + i2c0: i2c@fcfee000 { + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee000 0x44>; + interrupts = <0 157 IRQ_TYPE_LEVEL_HIGH>, + <0 158 IRQ_TYPE_EDGE_RISING>, + <0 159 IRQ_TYPE_EDGE_RISING>, + <0 160 IRQ_TYPE_LEVEL_HIGH>, + <0 161 IRQ_TYPE_LEVEL_HIGH>, + <0 162 IRQ_TYPE_LEVEL_HIGH>, + <0 163 IRQ_TYPE_LEVEL_HIGH>, + <0 164 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml b/Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml new file mode 100644 index 000000000..4f746bef2 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml @@ -0,0 +1,156 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/snps,designware-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare APB I2C Controller + +maintainers: + - Jarkko Nikula <jarkko.nikula@linux.intel.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + - if: + properties: + compatible: + not: + contains: + const: mscc,ocelot-i2c + then: + properties: + reg: + maxItems: 1 + +properties: + compatible: + oneOf: + - description: Generic Synopsys DesignWare I2C controller + const: snps,designware-i2c + - description: Microsemi Ocelot SoCs I2C controller + items: + - const: mscc,ocelot-i2c + - const: snps,designware-i2c + - description: Baikal-T1 SoC System I2C controller + const: baikal,bt1-sys-i2c + + reg: + minItems: 1 + items: + - description: DW APB I2C controller memory mapped registers + - description: | + ICPU_CFG:TWI_DELAY registers to setup the SDA hold time. + This registers are specific to the Ocelot I2C-controller. + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: I2C controller reference clock source + - description: APB interface clock source + + clock-names: + minItems: 1 + items: + - const: ref + - const: pclk + + resets: + maxItems: 1 + + clock-frequency: + description: Desired I2C bus clock frequency in Hz + enum: [100000, 400000, 1000000, 3400000] + default: 400000 + + i2c-sda-hold-time-ns: + maxItems: 1 + description: | + The property should contain the SDA hold time in nanoseconds. This option + is only supported in hardware blocks version 1.11a or newer or on + Microsemi SoCs. + + i2c-scl-falling-time-ns: + maxItems: 1 + description: | + The property should contain the SCL falling time in nanoseconds. + This value is used to compute the tLOW period. + default: 300 + + i2c-sda-falling-time-ns: + maxItems: 1 + description: | + The property should contain the SDA falling time in nanoseconds. + This value is used to compute the tHIGH period. + default: 300 + + dmas: + items: + - description: TX DMA Channel + - description: RX DMA Channel + + dma-names: + items: + - const: tx + - const: rx + +unevaluatedProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - interrupts + +examples: + - | + i2c@f0000 { + compatible = "snps,designware-i2c"; + reg = <0xf0000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <11>; + clock-frequency = <400000>; + }; + - | + i2c@1120000 { + compatible = "snps,designware-i2c"; + reg = <0x1120000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <12 1>; + clock-frequency = <400000>; + i2c-sda-hold-time-ns = <300>; + i2c-sda-falling-time-ns = <300>; + i2c-scl-falling-time-ns = <300>; + }; + - | + i2c@2000 { + compatible = "snps,designware-i2c"; + reg = <0x2000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&i2cclk>; + interrupts = <0>; + + eeprom@64 { + compatible = "atmel,24c02"; + reg = <0x64>; + }; + }; + - | + i2c@100400 { + compatible = "mscc,ocelot-i2c", "snps,designware-i2c"; + reg = <0x100400 0x100>, <0x198 0x8>; + pinctrl-0 = <&i2c_pins>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <8>; + clocks = <&ahb_clk>; + }; +... diff --git a/Documentation/devicetree/bindings/i2c/socionext,uniphier-fi2c.yaml b/Documentation/devicetree/bindings/i2c/socionext,uniphier-fi2c.yaml new file mode 100644 index 000000000..c76131902 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/socionext,uniphier-fi2c.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/socionext,uniphier-fi2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UniPhier I2C controller (FIFO-builtin) + +maintainers: + - Masahiro Yamada <yamada.masahiro@socionext.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + const: socionext,uniphier-fi2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-frequency: + minimum: 100000 + maximum: 400000 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + i2c0: i2c@58780000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 4>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/socionext,uniphier-i2c.yaml b/Documentation/devicetree/bindings/i2c/socionext,uniphier-i2c.yaml new file mode 100644 index 000000000..ddde08636 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/socionext,uniphier-i2c.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/socionext,uniphier-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: UniPhier I2C controller (FIFO-less) + +maintainers: + - Masahiro Yamada <yamada.masahiro@socionext.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + const: socionext,uniphier-i2c + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-frequency: + minimum: 100000 + maximum: 400000 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + i2c0: i2c@58400000 { + compatible = "socionext,uniphier-i2c"; + reg = <0x58400000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 1>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml new file mode 100644 index 000000000..d747f4990 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml @@ -0,0 +1,144 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/st,stm32-i2c.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: I2C controller embedded in STMicroelectronics STM32 I2C platform + +maintainers: + - Pierre-Yves MORDRET <pierre-yves.mordret@st.com> + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + - if: + properties: + compatible: + contains: + enum: + - st,stm32f7-i2c + - st,stm32mp15-i2c + then: + properties: + i2c-scl-rising-time-ns: + default: 25 + + i2c-scl-falling-time-ns: + default: 10 + + st,syscfg-fmp: + description: Use to set Fast Mode Plus bit within SYSCFG when + Fast Mode Plus speed is selected by slave. + Format is phandle to syscfg / register offset within + syscfg / register bitmask for FMP bit. + $ref: "/schemas/types.yaml#/definitions/phandle-array" + items: + minItems: 3 + maxItems: 3 + + - if: + properties: + compatible: + contains: + enum: + - st,stm32f4-i2c + then: + properties: + clock-frequency: + enum: [100000, 400000] + +properties: + compatible: + enum: + - st,stm32f4-i2c + - st,stm32f7-i2c + - st,stm32mp15-i2c + + reg: + maxItems: 1 + + interrupts: + items: + - description: interrupt ID for I2C event + - description: interrupt ID for I2C error + + resets: + maxItems: 1 + + clocks: + maxItems: 1 + + dmas: + items: + - description: RX DMA Channel phandle + - description: TX DMA Channel phandle + + dma-names: + items: + - const: rx + - const: tx + + clock-frequency: + description: Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. + For STM32F7, STM32H7 and STM32MP1 SoCs, if timing parameters + match, the bus clock frequency can be from 1Hz to 1MHz. + default: 100000 + minimum: 1 + maximum: 1000000 + +required: + - compatible + - reg + - interrupts + - resets + - clocks + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/mfd/stm32f7-rcc.h> + #include <dt-bindings/clock/stm32fx-clock.h> + //Example 1 (with st,stm32f4-i2c compatible) + i2c@40005400 { + compatible = "st,stm32f4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc 277>; + clocks = <&rcc 0 149>; + }; + + //Example 2 (with st,stm32f7-i2c compatible) + i2c@40005800 { + compatible = "st,stm32f7-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005800 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc STM32F7_APB1_RESET(I2C1)>; + clocks = <&rcc 1 CLK_I2C1>; + }; + + //Example 3 (with st,stm32mp15-i2c compatible on stm32mp) + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + i2c@40013000 { + compatible = "st,stm32mp15-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40013000 0x400>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C2_K>; + resets = <&rcc I2C2_R>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + st,syscfg-fmp = <&syscfg 0x4 0x2>; + }; +... diff --git a/Documentation/devicetree/bindings/i2c/xlnx,xps-iic-2.00.a.yaml b/Documentation/devicetree/bindings/i2c/xlnx,xps-iic-2.00.a.yaml new file mode 100644 index 000000000..ffb2ed039 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/xlnx,xps-iic-2.00.a.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/i2c/xlnx,xps-iic-2.00.a.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: ilinx IIC controller Device Tree Bindings + +maintainers: + - info@mocean-labs.com + +allOf: + - $ref: /schemas/i2c/i2c-controller.yaml# + +properties: + compatible: + const: xlnx,xps-iic-2.00.a + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + + clock-name: + const: pclk + description: | + Input clock name. + +required: + - compatible + - reg + - interrupts + - clocks + +unevaluatedProperties: false + +examples: + - | + axi_iic_0: i2c@40800000 { + compatible = "xlnx,xps-iic-2.00.a"; + clocks = <&clkc 15>; + interrupts = < 1 2 >; + reg = < 0x40800000 0x10000 >; + + #size-cells = <0>; + #address-cells = <1>; + }; |