summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/iio/frequency/adf4350.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/iio/frequency/adf4350.txt')
-rw-r--r--Documentation/devicetree/bindings/iio/frequency/adf4350.txt86
1 files changed, 86 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/frequency/adf4350.txt b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt
new file mode 100644
index 000000000..f8c181d81
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/frequency/adf4350.txt
@@ -0,0 +1,86 @@
+Analog Devices ADF4350/ADF4351 device driver
+
+Required properties:
+ - compatible: Should be one of
+ * "adi,adf4350": When using the ADF4350 device
+ * "adi,adf4351": When using the ADF4351 device
+ - reg: SPI chip select numbert for the device
+ - spi-max-frequency: Max SPI frequency to use (< 20000000)
+ - clocks: From common clock binding. Clock is phandle to clock for
+ ADF435x Reference Clock (CLKIN).
+
+Optional properties:
+ - gpios: GPIO Lock detect - If set with a valid phandle and GPIO number,
+ pll lock state is tested upon read.
+ - adi,channel-spacing: Channel spacing in Hz (influences MODULUS).
+ - adi,power-up-frequency: If set in Hz the PLL tunes to
+ the desired frequency on probe.
+ - adi,reference-div-factor: If set the driver skips dynamic calculation
+ and uses this default value instead.
+ - adi,reference-doubler-enable: Enables reference doubler.
+ - adi,reference-div2-enable: Enables reference divider.
+ - adi,phase-detector-polarity-positive-enable: Enables positive phase
+ detector polarity. Default = negative.
+ - adi,lock-detect-precision-6ns-enable: Enables 6ns lock detect precision.
+ Default = 10ns.
+ - adi,lock-detect-function-integer-n-enable: Enables lock detect
+ for integer-N mode. Default = factional-N mode.
+ - adi,charge-pump-current: Charge pump current in mA.
+ Default = 2500mA.
+ - adi,muxout-select: On chip multiplexer output selection.
+ Valid values for the multiplexer output are:
+ 0: Three-State Output (default)
+ 1: DVDD
+ 2: DGND
+ 3: R-Counter output
+ 4: N-Divider output
+ 5: Analog lock detect
+ 6: Digital lock detect
+ - adi,low-spur-mode-enable: Enables low spur mode.
+ Default = Low noise mode.
+ - adi,cycle-slip-reduction-enable: Enables cycle slip reduction.
+ - adi,charge-cancellation-enable: Enabled charge pump
+ charge cancellation for integer-N modes.
+ - adi,anti-backlash-3ns-enable: Enables 3ns antibacklash pulse width
+ for integer-N modes.
+ - adi,band-select-clock-mode-high-enable: Enables faster band
+ selection logic.
+ - adi,12bit-clk-divider: Clock divider value used when
+ adi,12bit-clkdiv-mode != 0
+ - adi,clk-divider-mode:
+ Valid values for the clkdiv mode are:
+ 0: Clock divider off (default)
+ 1: Fast lock enable
+ 2: Phase resync enable
+ - adi,aux-output-enable: Enables auxiliary RF output.
+ - adi,aux-output-fundamental-enable: Selects fundamental VCO output on
+ the auxiliary RF output. Default = Output of RF dividers.
+ - adi,mute-till-lock-enable: Enables Mute-Till-Lock-Detect function.
+ - adi,output-power: Output power selection.
+ Valid values for the power mode are:
+ 0: -4dBm (default)
+ 1: -1dBm
+ 2: +2dBm
+ 3: +5dBm
+ - adi,aux-output-power: Auxiliary output power selection.
+ Valid values for the power mode are:
+ 0: -4dBm (default)
+ 1: -1dBm
+ 2: +2dBm
+ 3: +5dBm
+
+
+Example:
+ lo_pll0_rx_adf4351: adf4351-rx-lpc@4 {
+ compatible = "adi,adf4351";
+ reg = <4>;
+ spi-max-frequency = <10000000>;
+ clocks = <&clk0_ad9523 9>;
+ clock-names = "clkin";
+ adi,channel-spacing = <10000>;
+ adi,power-up-frequency = <2400000000>;
+ adi,phase-detector-polarity-positive-enable;
+ adi,charge-pump-current = <2500>;
+ adi,output-power = <3>;
+ adi,mute-till-lock-enable;
+ };