diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/humidity')
5 files changed, 121 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/humidity/dht11.txt b/Documentation/devicetree/bindings/iio/humidity/dht11.txt new file mode 100644 index 000000000..ecc24c199 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/dht11.txt @@ -0,0 +1,14 @@ +* DHT11 humidity/temperature sensor (and compatibles like DHT22) + +Required properties: + - compatible: Should be "dht11" + - gpios: Should specify the GPIO connected to the sensor's data + line, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. + +Example: + +humidity_sensor { + compatible = "dht11"; + gpios = <&gpio0 6 0>; +} diff --git a/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt new file mode 100644 index 000000000..c52333bdf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt @@ -0,0 +1,17 @@ +* HDC100x temperature + humidity sensors + +Required properties: + - compatible: Should contain one of the following: + ti,hdc1000 + ti,hdc1008 + ti,hdc1010 + ti,hdc1050 + ti,hdc1080 + - reg: i2c address of the sensor + +Example: + +hdc100x@40 { + compatible = "ti,hdc1000"; + reg = <0x40>; +}; diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt new file mode 100644 index 000000000..84d029372 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/hts221.txt @@ -0,0 +1,30 @@ +* HTS221 STM humidity + temperature sensor + +Required properties: +- compatible: should be "st,hts221" +- reg: i2c address of the sensor / spi cs line + +Optional properties: +- drive-open-drain: the interrupt/data ready line will be configured + as open drain, which is useful if several sensors share the same + interrupt line. This is a boolean property. + If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or + IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line + when it is not active, whereas a pull-up one is needed when interrupt + line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING. + Refer to pinctrl/pinctrl-bindings.txt for the property description. +- interrupts: interrupt mapping for IRQ. It should be configured with + flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or + IRQ_TYPE_EDGE_FALLING. + + Refer to interrupt-controller/interrupts.txt for generic interrupt + client node bindings. + +Example: + +hts221@5f { + compatible = "st,hts221"; + reg = <0x5f>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; +}; diff --git a/Documentation/devicetree/bindings/iio/humidity/htu21.txt b/Documentation/devicetree/bindings/iio/humidity/htu21.txt new file mode 100644 index 000000000..97d79636f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/htu21.txt @@ -0,0 +1,13 @@ +*HTU21 - Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor + +Required properties: + + - compatible: should be "meas,htu21" or "meas,ms8607-humidity" + - reg: I2C address of the sensor + +Example: + +htu21@40 { + compatible = "meas,htu21"; + reg = <0x40>; +}; diff --git a/Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml b/Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml new file mode 100644 index 000000000..7037f82ec --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/ti,hdc2010.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/humidity/ti,hdc2010.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HDC2010/HDC2080 humidity and temperature iio sensors + +maintainers: + - Eugene Zaikonnikov <ez@norophonic.com> + +description: | + Relative humidity and tempereature sensors on I2C bus + + Datasheets are available at: + http://www.ti.com/product/HDC2010/datasheet + http://www.ti.com/product/HDC2080/datasheet + +properties: + compatible: + enum: + - ti,hdc2010 + - ti,hdc2080 + + vdd-supply: + maxItems: 1 + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + humidity@40 { + compatible = "ti,hdc2010"; + reg = <0x40>; + }; + }; |