summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/media/i2c/adv7604.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c/adv7604.txt')
-rw-r--r--Documentation/devicetree/bindings/media/i2c/adv7604.txt88
1 files changed, 88 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
new file mode 100644
index 000000000..b3e688b77
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
@@ -0,0 +1,88 @@
+* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
+
+The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
+HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
+input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
+similar to the 7611 but has 2 HDMI inputs.
+
+These device tree bindings support the ADV7611/12 only at the moment.
+
+Required Properties:
+
+ - compatible: Must contain one of the following
+ - "adi,adv7611" for the ADV7611
+ - "adi,adv7612" for the ADV7612
+
+ - reg: I2C slave addresses
+ The ADV76xx has up to thirteen 256-byte maps that can be accessed via the
+ main I2C ports. Each map has it own I2C address and acts as a standard
+ slave device on the I2C bus. The main address is mandatory, others are
+ optional and revert to defaults if not specified.
+
+ - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
+ detection pins, one per HDMI input. The active flag indicates the GPIO
+ level that enables hot-plug detection.
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+ Port ADV7611 ADV7612
+------------------------------------------------------------
+ HDMI 0 0, 1
+ Digital output 1 2
+
+The digital output port node must contain at least one endpoint.
+
+Optional Properties:
+
+ - reset-gpios: Reference to the GPIO connected to the device's reset pin.
+ - default-input: Select which input is selected after reset.
+ - reg-names : Names of maps with programmable addresses.
+ It can contain any map needing a non-default address.
+ Possible maps names are :
+ "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe",
+ "rep", "edid", "hdmi", "test", "cp", "vdp"
+
+Optional Endpoint Properties:
+
+ The following three properties are defined in video-interfaces.txt and are
+ valid for source endpoints only.
+
+ - hsync-active: Horizontal synchronization polarity. Defaults to active low.
+ - vsync-active: Vertical synchronization polarity. Defaults to active low.
+ - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
+
+ If none of hsync-active, vsync-active and pclk-sample is specified the
+ endpoint will use embedded BT.656 synchronization.
+
+Example:
+
+ hdmi_receiver@4c {
+ compatible = "adi,adv7611";
+ /*
+ * The edid page will be accessible @ 0x66 on the I2C bus. All
+ * other maps will retain their default addresses.
+ */
+ reg = <0x4c>, <0x66>;
+ reg-names = "main", "edid";
+
+ reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+ hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ default-input = <0>;
+
+ port@0 {
+ reg = <0>;
+ };
+ port@1 {
+ reg = <1>;
+ hdmi_in: endpoint {
+ remote-endpoint = <&ccdc_in>;
+ };
+ };
+ };