diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/rk808.txt | 277 |
1 files changed, 277 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt new file mode 100644 index 000000000..04df07f6f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -0,0 +1,277 @@ +RK8XX Power Management Integrated Circuit + +The rk8xx family current members: +rk805 +rk808 +rk809 +rk817 +rk818 + +Required properties: +- compatible: "rockchip,rk805" +- compatible: "rockchip,rk808" +- compatible: "rockchip,rk809" +- compatible: "rockchip,rk817" +- compatible: "rockchip,rk818" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller. +- #clock-cells: from common clock binding; shall be set to 1 (multiple clock + outputs). See <dt-bindings/clock/rockchip,rk808.h> for clock IDs. + +Optional properties: +- clock-output-names: From common clock binding to override the + default output clock name +- rockchip,system-power-controller: Telling whether or not this pmic is controlling + the system power. + +Optional RK805 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc5-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc6-supply: The input supply for LDO_REG3 + +Optional RK808 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3 and LDO_REG7 +- vcc8-supply: The input supply for SWITCH_REG1 +- vcc9-supply: The input supply for LDO_REG4 and LDO_REG5 +- vcc10-supply: The input supply for LDO_REG6 +- vcc11-supply: The input supply for LDO_REG8 +- vcc12-supply: The input supply for SWITCH_REG2 +- dvs-gpios: buck1/2 can be controlled by gpio dvs, this is GPIO specifiers + for 2 host gpio's used for dvs. The format of the gpio specifier depends in + the gpio controller. If DVS GPIOs aren't present, voltage changes will happen + very quickly with no slow ramp time. + +Optional shared RK809 and RK817 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc5-supply: The input supply for LDO_REG1, LDO_REG2, LDO_REG3 +- vcc6-supply: The input supply for LDO_REG4, LDO_REG5, LDO_REG6 +- vcc7-supply: The input supply for LDO_REG7, LDO_REG8, LDO_REG9 + +Optional RK809 properties: +- vcc8-supply: The input supply for SWITCH_REG1 +- vcc9-supply: The input supply for DCDC_REG5, SWITCH_REG2 + +Optional RK817 properties: +- vcc8-supply: The input supply for BOOST +- vcc9-supply: The input supply for OTG_SWITCH + +Optional RK818 properties: +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- boost-supply: The input supply for DCDC_BOOST +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3, LDO_REG5 and LDO_REG7 +- vcc8-supply: The input supply for LDO_REG4, LDO_REG6 and LDO_REG8 +- vcc9-supply: The input supply for LDO_REG9 and SWITCH_REG +- h_5v-supply: The input supply for HDMI_SWITCH +- usb-supply: The input supply for OTG_SWITCH + +Regulators: All the regulators of RK8XX to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the RK805 PMIC regulators are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK805 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 3 + +Following regulators of the RK808 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK808 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 8. + - SWITCH_REGn + - valid values for n are 1 to 2 + +Following regulators of the RK809 and RK817 PMIC blocks are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK809 and RK817 datasheets. + + - DCDC_REGn + - valid values for n are 1 to 5 for RK809. + - valid values for n are 1 to 4 for RK817. + - LDO_REGn + - valid values for n are 1 to 9 for RK809. + - valid values for n are 1 to 9 for RK817. + - SWITCH_REGn + - valid values for n are 1 to 2 for RK809. + - BOOST for RK817 + - OTG_SWITCH for RK817 + +Following regulators of the RK818 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK818 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 9. + - SWITCH_REG + - HDMI_SWITCH + - OTG_SWITCH + +It is necessary to configure three pins for both the RK809 and RK817, the three +pins are "gpio_ts" "gpio_gt" "gpio_slp". + The gpio_gt and gpio_ts pins support the gpio function. + The gpio_slp pin is for controlling the pmic states, as below: + - reset + - power down + - sleep + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details + +Example: + rk808: pmic@1b { + compatible = "rockchip,rk808"; + clock-output-names = "xin32k", "rk808-clkout2"; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int &dvs_1 &dvs_2>; + dvs-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>, + <&gpio7 15 GPIO_ACTIVE_HIGH>; + reg = <0x1b>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vccio_pmu>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd_arm"; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + }; + + vccio_pmu: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_pmu"; + }; + + vcc_tp: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_tp"; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + }; + }; + }; |