diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt | 143 |
1 files changed, 143 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt new file mode 100644 index 000000000..96c0b1440 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt @@ -0,0 +1,143 @@ +* NVIDIA Tegra Secure Digital Host Controller + +This controller on Tegra family SoCs provides an interface for MMC, SD, +and SDIO types of memory cards. + +This file documents differences between the core properties described +by mmc.txt and the properties used by the sdhci-tegra driver. + +Required properties: +- compatible : should be one of: + - "nvidia,tegra20-sdhci": for Tegra20 + - "nvidia,tegra30-sdhci": for Tegra30 + - "nvidia,tegra114-sdhci": for Tegra114 + - "nvidia,tegra124-sdhci": for Tegra124 and Tegra132 + - "nvidia,tegra210-sdhci": for Tegra210 + - "nvidia,tegra186-sdhci": for Tegra186 + - "nvidia,tegra194-sdhci": for Tegra194 +- clocks: For Tegra210, Tegra186 and Tegra194 must contain two entries. + One for the module clock and one for the timeout clock. + For all other Tegra devices, must contain a single entry for + the module clock. See ../clocks/clock-bindings.txt for details. +- clock-names: For Tegra210, Tegra186 and Tegra194 must contain the + strings 'sdhci' and 'tmclk' to represent the module and + the timeout clocks, respectively. + For all other Tegra devices must contain the string 'sdhci' + to represent the module clock. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - sdhci + +Optional properties: +- power-gpios : Specify GPIOs for power control + +Example: + +sdhci@c8000200 { + compatible = "nvidia,tegra20-sdhci"; + reg = <0xc8000200 0x200>; + interrupts = <47>; + clocks = <&tegra_car 14>; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + cd-gpios = <&gpio 69 0>; /* gpio PI5 */ + wp-gpios = <&gpio 57 0>; /* gpio PH1 */ + power-gpios = <&gpio 155 0>; /* gpio PT3 */ + bus-width = <8>; +}; + +Optional properties for Tegra210, Tegra186 and Tegra194: +- pinctrl-names, pinctrl-0, pinctrl-1 : Specify pad voltage + configurations. Valid pinctrl-names are "sdmmc-3v3" and "sdmmc-1v8" + for controllers supporting multiple voltage levels. The order of names + should correspond to the pin configuration states in pinctrl-0 and + pinctrl-1. +- pinctrl-names : "sdmmc-3v3-drv" and "sdmmc-1v8-drv" are applicable for + Tegra210 where pad config registers are in the pinmux register domain + for pull-up-strength and pull-down-strength values configuration when + using pads at 3V3 and 1V8 levels. +- nvidia,only-1-8-v : The presence of this property indicates that the + controller operates at a 1.8 V fixed I/O voltage. +- nvidia,pad-autocal-pull-up-offset-3v3, + nvidia,pad-autocal-pull-down-offset-3v3 : Specify drive strength + calibration offsets for 3.3 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-1v8, + nvidia,pad-autocal-pull-down-offset-1v8 : Specify drive strength + calibration offsets for 1.8 V signaling modes. +- nvidia,pad-autocal-pull-up-offset-3v3-timeout, + nvidia,pad-autocal-pull-down-offset-3v3-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 3.3 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-1v8-timeout, + nvidia,pad-autocal-pull-down-offset-1v8-timeout : Specify drive + strength used as a fallback in case the automatic calibration times + out on a 1.8 V signaling mode. +- nvidia,pad-autocal-pull-up-offset-sdr104, + nvidia,pad-autocal-pull-down-offset-sdr104 : Specify drive strength + calibration offsets for SDR104 mode. +- nvidia,pad-autocal-pull-up-offset-hs400, + nvidia,pad-autocal-pull-down-offset-hs400 : Specify drive strength + calibration offsets for HS400 mode. +- nvidia,default-tap : Specify the default inbound sampling clock + trimmer value for non-tunable modes. +- nvidia,default-trim : Specify the default outbound clock trimmer + value. +- nvidia,dqs-trim : Specify DQS trim value for HS400 timing + + Notes on the pad calibration pull up and pulldown offset values: + - The property values are drive codes which are programmed into the + PD_OFFSET and PU_OFFSET sections of the + SDHCI_TEGRA_AUTO_CAL_CONFIG register. + - A higher value corresponds to higher drive strength. Please refer + to the reference manual of the SoC for correct values. + - The SDR104 and HS400 timing specific values are used in + corresponding modes if specified. + + Notes on tap and trim values: + - The values are used for compensating trace length differences + by adjusting the sampling point. + - The values are programmed to the Vendor Clock Control Register. + Please refer to the reference manual of the SoC for correct + values. + - The DQS trim values are only used on controllers which support + HS400 timing. Only SDMMC4 on Tegra210 and Tegra 186 supports + HS400. + +Example: +sdhci@700b0000 { + compatible = "nvidia,tegra124-sdhci"; + reg = <0x0 0x700b0000 0x0 0x200>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SDMMC1>; + clock-names = "sdhci"; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; + nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; + nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; + nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; + status = "disabled"; +}; + +sdhci@700b0000 { + compatible = "nvidia,tegra210-sdhci"; + reg = <0x0 0x700b0000 0x0 0x200>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA210_CLK_SDMMC1>, + <&tegra_car TEGRA210_CLK_SDMMC_LEGACY>; + clock-names = "sdhci", "tmclk"; + resets = <&tegra_car 14>; + reset-names = "sdhci"; + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + nvidia,pad-autocal-pull-up-offset-3v3 = <0x00>; + nvidia,pad-autocal-pull-down-offset-3v3 = <0x7d>; + nvidia,pad-autocal-pull-up-offset-1v8 = <0x7b>; + nvidia,pad-autocal-pull-down-offset-1v8 = <0x7b>; + status = "disabled"; +}; |