diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/qca8k.txt | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt new file mode 100644 index 000000000..ccbc6d893 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -0,0 +1,175 @@ +* Qualcomm Atheros QCA8xxx switch family + +Required properties: + +- compatible: should be one of: + "qca,qca8334" + "qca,qca8337" + +- #size-cells: must be 0 +- #address-cells: must be 1 + +Optional properties: + +- reset-gpios: GPIO to be used to reset the whole device + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external +mdio-bus each subnode describing a port needs to have a valid phandle +referencing the internal PHY it is connected to. This is because there's no +N:N mapping of port and PHY id. + +Don't use mixed external and internal mdio-bus configurations, as this is +not supported by the hardware. + +The CPU port of this switch is always port 0. + +A CPU port node has the following optional node: + +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +For QCA8K the 'fixed-link' sub-node supports only the following properties: + +- 'speed' (integer, mandatory), to indicate the link speed. Accepted + values are 10, 100 and 1000 +- 'full-duplex' (boolean, optional), to indicate that full duplex is + used. When absent, half duplex is assumed. + +Examples: + +for the external mdio-bus configuration: + + &mdio0 { + phy_port1: phy@0 { + reg = <0>; + }; + + phy_port2: phy@1 { + reg = <1>; + }; + + phy_port3: phy@2 { + reg = <2>; + }; + + phy_port4: phy@3 { + reg = <3>; + }; + + phy_port5: phy@4 { + reg = <4>; + }; + + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-handle = <&phy_port5>; + }; + }; + }; + }; + +for the internal master mdio-bus configuration: + + &mdio0 { + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "wan"; + }; + }; + }; + }; |