summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/dsa
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/net/dsa/ar9331.txt148
-rw-r--r--Documentation/devicetree/bindings/net/dsa/b53.txt149
-rw-r--r--Documentation/devicetree/bindings/net/dsa/dsa.txt4
-rw-r--r--Documentation/devicetree/bindings/net/dsa/dsa.yaml94
-rw-r--r--Documentation/devicetree/bindings/net/dsa/ksz.txt125
-rw-r--r--Documentation/devicetree/bindings/net/dsa/lan9303.txt102
-rw-r--r--Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt143
-rw-r--r--Documentation/devicetree/bindings/net/dsa/marvell.txt109
-rw-r--r--Documentation/devicetree/bindings/net/dsa/mt7530.txt315
-rw-r--r--Documentation/devicetree/bindings/net/dsa/ocelot.txt213
-rw-r--r--Documentation/devicetree/bindings/net/dsa/qca8k.txt175
-rw-r--r--Documentation/devicetree/bindings/net/dsa/realtek-smi.txt153
-rw-r--r--Documentation/devicetree/bindings/net/dsa/sja1105.txt156
-rw-r--r--Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt131
14 files changed, 2017 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt
new file mode 100644
index 000000000..320607cbb
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt
@@ -0,0 +1,148 @@
+Atheros AR9331 built-in switch
+=============================
+
+It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal
+MDIO bus. All PHYs are built-in as well.
+
+Required properties:
+
+ - compatible: should be: "qca,ar9331-switch"
+ - reg: Address on the MII bus for the switch.
+ - resets : Must contain an entry for each entry in reset-names.
+ - reset-names : Must include the following entries: "switch"
+ - interrupt-parent: Phandle to the parent interrupt controller
+ - interrupts: IRQ line for the switch
+ - interrupt-controller: Indicates the switch is itself an interrupt
+ controller. This is used for the PHY interrupts.
+ - #interrupt-cells: must be 1
+ - mdio: Container of PHY and devices on the switches MDIO bus.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+Examples:
+
+eth0: ethernet@19000000 {
+ compatible = "qca,ar9330-eth";
+ reg = <0x19000000 0x200>;
+ interrupts = <4>;
+
+ resets = <&rst 9>, <&rst 22>;
+ reset-names = "mac", "mdio";
+ clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+ clock-names = "eth", "mdio";
+
+ phy-mode = "mii";
+ phy-handle = <&phy_port4>;
+};
+
+eth1: ethernet@1a000000 {
+ compatible = "qca,ar9330-eth";
+ reg = <0x1a000000 0x200>;
+ interrupts = <5>;
+ resets = <&rst 13>, <&rst 23>;
+ reset-names = "mac", "mdio";
+ clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+ clock-names = "eth", "mdio";
+
+ phy-mode = "gmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch10: switch@10 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ compatible = "qca,ar9331-switch";
+ reg = <0x10>;
+ resets = <&rst 8>;
+ reset-names = "switch";
+
+ interrupt-parent = <&miscintc>;
+ interrupts = <12>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch_port0: port@0 {
+ reg = <0x0>;
+ label = "cpu";
+ ethernet = <&eth1>;
+
+ phy-mode = "gmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ switch_port1: port@1 {
+ reg = <0x1>;
+ phy-handle = <&phy_port0>;
+ phy-mode = "internal";
+ };
+
+ switch_port2: port@2 {
+ reg = <0x2>;
+ phy-handle = <&phy_port1>;
+ phy-mode = "internal";
+ };
+
+ switch_port3: port@3 {
+ reg = <0x3>;
+ phy-handle = <&phy_port2>;
+ phy-mode = "internal";
+ };
+
+ switch_port4: port@4 {
+ reg = <0x4>;
+ phy-handle = <&phy_port3>;
+ phy-mode = "internal";
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&switch10>;
+
+ phy_port0: phy@0 {
+ reg = <0x0>;
+ interrupts = <0>;
+ };
+
+ phy_port1: phy@1 {
+ reg = <0x1>;
+ interrupts = <0>;
+ };
+
+ phy_port2: phy@2 {
+ reg = <0x2>;
+ interrupts = <0>;
+ };
+
+ phy_port3: phy@3 {
+ reg = <0x3>;
+ interrupts = <0>;
+ };
+
+ phy_port4: phy@4 {
+ reg = <0x4>;
+ interrupts = <0>;
+ };
+ };
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt
new file mode 100644
index 000000000..f1487a751
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/b53.txt
@@ -0,0 +1,149 @@
+Broadcom BCM53xx Ethernet switches
+==================================
+
+Required properties:
+
+- compatible: For external switch chips, compatible string must be exactly one
+ of: "brcm,bcm5325"
+ "brcm,bcm53115"
+ "brcm,bcm53125"
+ "brcm,bcm53128"
+ "brcm,bcm5365"
+ "brcm,bcm5395"
+ "brcm,bcm5389"
+ "brcm,bcm5397"
+ "brcm,bcm5398"
+
+ For the BCM11360 SoC, must be:
+ "brcm,bcm11360-srab" and the mandatory "brcm,cygnus-srab" string
+
+ For the BCM5310x SoCs with an integrated switch, must be one of:
+ "brcm,bcm53010-srab"
+ "brcm,bcm53011-srab"
+ "brcm,bcm53012-srab"
+ "brcm,bcm53018-srab"
+ "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string
+
+ For the BCM5831X/BCM1140x SoCs with an integrated switch, must be one of:
+ "brcm,bcm11404-srab"
+ "brcm,bcm11407-srab"
+ "brcm,bcm11409-srab"
+ "brcm,bcm58310-srab"
+ "brcm,bcm58311-srab"
+ "brcm,bcm58313-srab" and the mandatory "brcm,omega-srab" string
+
+ For the BCM585xx/586XX/88312 SoCs with an integrated switch, must be one of:
+ "brcm,bcm58522-srab"
+ "brcm,bcm58523-srab"
+ "brcm,bcm58525-srab"
+ "brcm,bcm58622-srab"
+ "brcm,bcm58623-srab"
+ "brcm,bcm58625-srab"
+ "brcm,bcm88312-srab" and the mandatory "brcm,nsp-srab string
+
+ For the BCM63xx/33xx SoCs with an integrated switch, must be one of:
+ "brcm,bcm3384-switch"
+ "brcm,bcm6328-switch"
+ "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch"
+
+Required properties for BCM585xx/586xx/88312 SoCs:
+
+ - reg: a total of 3 register base addresses, the first one must be the
+ Switch Register Access block base, the second is the port 5/4 mux
+ configuration register and the third one is the SGMII configuration
+ and status register base address.
+
+ - interrupts: a total of 13 interrupts must be specified, in the following
+ order: port 0-5, 7-8 link status change, then the integrated PHY interrupt,
+ then the timestamping interrupt and the sleep timer interrupts for ports
+ 5,7,8.
+
+Optional properties for BCM585xx/586xx/88312 SoCs:
+
+ - reg-names: a total of 3 names matching the 3 base register address, must
+ be in the following order:
+ "srab"
+ "mux_config"
+ "sgmii_config"
+
+ - interrupt-names: a total of 13 names matching the 13 interrupts specified
+ must be in the following order:
+ "link_state_p0"
+ "link_state_p1"
+ "link_state_p2"
+ "link_state_p3"
+ "link_state_p4"
+ "link_state_p5"
+ "link_state_p7"
+ "link_state_p8"
+ "phy"
+ "ts"
+ "imp_sleep_timer_p5"
+ "imp_sleep_timer_p7"
+ "imp_sleep_timer_p8"
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+
+Examples:
+
+Ethernet switch connected via MDIO to the host, CPU port wired to eth0:
+
+ eth0: ethernet@10001000 {
+ compatible = "brcm,unimac";
+ reg = <0x10001000 0x1000>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ mdio0: mdio@10000000 {
+ compatible = "brcm,unimac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0: ethernet-switch@1e {
+ compatible = "brcm,bcm53125";
+ reg = <30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port1@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port5@5 {
+ reg = <5>;
+ label = "cable-modem";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ phy-mode = "rgmii-txid";
+ };
+
+ port8@8 {
+ reg = <8>;
+ label = "cpu";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ phy-mode = "rgmii-txid";
+ ethernet = <&eth0>;
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt
new file mode 100644
index 000000000..dab208b5c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt
@@ -0,0 +1,4 @@
+Distributed Switch Architecture Device Tree Bindings
+----------------------------------------------------
+
+See Documentation/devicetree/bindings/net/dsa/dsa.yaml for the documentation.
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml
new file mode 100644
index 000000000..a765ceba2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml
@@ -0,0 +1,94 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/dsa.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ethernet Switch Device Tree Bindings
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+ - Florian Fainelli <f.fainelli@gmail.com>
+ - Vivien Didelot <vivien.didelot@gmail.com>
+
+description:
+ This binding represents Ethernet Switches which have a dedicated CPU
+ port. That port is usually connected to an Ethernet Controller of the
+ SoC. Such setups are typical for embedded devices.
+
+select: false
+
+properties:
+ $nodename:
+ pattern: "^switch(@.*)?$"
+
+ dsa,member:
+ minItems: 2
+ maxItems: 2
+ description:
+ A two element list indicates which DSA cluster, and position within the
+ cluster a switch takes. <0 0> is cluster 0, switch 0. <0 1> is cluster 0,
+ switch 1. <1 0> is cluster 1, switch 0. A switch not part of any cluster
+ (single device hanging off a CPU port) must not specify this property
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
+patternProperties:
+ "^(ethernet-)?ports$":
+ type: object
+ properties:
+ '#address-cells':
+ const: 1
+ '#size-cells':
+ const: 0
+
+ patternProperties:
+ "^(ethernet-)?port@[0-9]+$":
+ type: object
+ description: Ethernet switch ports
+
+ properties:
+ reg:
+ description: Port number
+
+ label:
+ description:
+ Describes the label associated with this port, which will become
+ the netdev name
+ $ref: /schemas/types.yaml#definitions/string
+
+ link:
+ description:
+ Should be a list of phandles to other switch's DSA port. This
+ port is used as the outgoing port towards the phandle ports. The
+ full routing information must be given, not just the one hop
+ routes to neighbouring switches
+ $ref: /schemas/types.yaml#definitions/phandle-array
+
+ ethernet:
+ description:
+ Should be a phandle to a valid Ethernet device node. This host
+ device is what the switch port is connected to
+ $ref: /schemas/types.yaml#definitions/phandle
+
+ phy-handle: true
+
+ phy-mode: true
+
+ fixed-link: true
+
+ mac-address: true
+
+ required:
+ - reg
+
+ additionalProperties: false
+
+oneOf:
+ - required:
+ - ports
+ - required:
+ - ethernet-ports
+
+additionalProperties: true
+
+...
diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt
new file mode 100644
index 000000000..95e91e841
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt
@@ -0,0 +1,125 @@
+Microchip KSZ Series Ethernet switches
+==================================
+
+Required properties:
+
+- compatible: For external switch chips, compatible string must be exactly one
+ of the following:
+ - "microchip,ksz8765"
+ - "microchip,ksz8794"
+ - "microchip,ksz8795"
+ - "microchip,ksz9477"
+ - "microchip,ksz9897"
+ - "microchip,ksz9896"
+ - "microchip,ksz9567"
+ - "microchip,ksz8565"
+ - "microchip,ksz9893"
+ - "microchip,ksz9563"
+ - "microchip,ksz8563"
+
+Optional properties:
+
+- reset-gpios : Should be a gpio specifier for a reset line
+- microchip,synclko-125 : Set if the output SYNCLKO frequency should be set to
+ 125MHz instead of 25MHz.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required and optional properties.
+
+Examples:
+
+Ethernet switch connected via SPI to the host, CPU port wired to eth0:
+
+ eth0: ethernet@10001000 {
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ spi1: spi@f8008000 {
+ pinctrl-0 = <&pinctrl_spi_ksz>;
+ cs-gpios = <&pioC 25 0>;
+ id = <1>;
+
+ ksz9477: ksz9477@0 {
+ compatible = "microchip,ksz9477";
+ reg = <0>;
+
+ spi-max-frequency = <44000000>;
+ spi-cpha;
+ spi-cpol;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ port@4 {
+ reg = <4>;
+ label = "lan5";
+ };
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&eth0>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ ksz8565: ksz8565@0 {
+ compatible = "microchip,ksz8565";
+ reg = <0>;
+
+ spi-max-frequency = <44000000>;
+ spi-cpha;
+ spi-cpol;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&eth0>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
new file mode 100644
index 000000000..464d6bf87
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
@@ -0,0 +1,102 @@
+SMSC/MicroChip LAN9303 three port ethernet switch
+-------------------------------------------------
+
+Required properties:
+
+- compatible: should be
+ - "smsc,lan9303-i2c" for I2C managed mode
+ or
+ - "smsc,lan9303-mdio" for mdio managed mode
+
+Optional properties:
+
+- reset-gpios: GPIO to be used to reset the whole device
+- reset-duration: reset duration in milliseconds, defaults to 200 ms
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt. The CPU port of this switch is always port 0.
+
+Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is
+configured to use 1/2/3 instead. This hardware configuration will be
+auto-detected and mapped accordingly.
+
+Example:
+
+I2C managed mode:
+
+ master: masterdevice@X {
+
+ fixed-link { /* RMII fixed link to LAN9303 */
+ speed = <100>;
+ full-duplex;
+ };
+ };
+
+ switch: switch@a {
+ compatible = "smsc,lan9303-i2c";
+ reg = <0xa>;
+ reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+ reset-duration = <200>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 { /* RMII fixed link to master */
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&master>;
+ };
+
+ port@1 { /* external port 1 */
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 { /* external port 2 */
+ reg = <2>;
+ label = "lan2";
+ };
+ };
+ };
+
+MDIO managed mode:
+
+ master: masterdevice@X {
+ phy-handle = <&switch>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch: switch-phy@0 {
+ compatible = "smsc,lan9303-mdio";
+ reg = <0>;
+ reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+ reset-duration = <100>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&master>;
+ };
+
+ port@1 { /* external port 1 */
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 { /* external port 2 */
+ reg = <2>;
+ label = "lan2";
+ };
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt
new file mode 100644
index 000000000..886cbe8ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt
@@ -0,0 +1,143 @@
+Lantiq GSWIP Ethernet switches
+==================================
+
+Required properties for GSWIP core:
+
+- compatible : "lantiq,xrx200-gswip" for the embedded GSWIP in the
+ xRX200 SoC
+- reg : memory range of the GSWIP core registers
+ : memory range of the GSWIP MDIO registers
+ : memory range of the GSWIP MII registers
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of
+additional required and optional properties.
+
+
+Required properties for MDIO bus:
+- compatible : "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP
+ core of the xRX200 SoC and the PHYs connected to it.
+
+See Documentation/devicetree/bindings/net/mdio.txt for a list of additional
+required and optional properties.
+
+
+Required properties for GPHY firmware loading:
+- compatible : "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"
+ "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw"
+ "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw"
+ for the loading of the firmware into the embedded
+ GPHY core of the SoC.
+- lantiq,rcu : reference to the rcu syscon
+
+The GPHY firmware loader has a list of GPHY entries, one for each
+embedded GPHY
+
+- reg : Offset of the GPHY firmware register in the RCU
+ register range
+- resets : list of resets of the embedded GPHY
+- reset-names : list of names of the resets
+
+Example:
+
+Ethernet switch on the VRX200 SoC:
+
+switch@e108000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "lantiq,xrx200-gswip";
+ reg = < 0xe108000 0x3100 /* switch */
+ 0xe10b100 0xd8 /* mdio */
+ 0xe10b1d8 0x130 /* mii */
+ >;
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan3";
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan4";
+ phy-mode = "rgmii";
+ phy-handle = <&phy1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-mode = "internal";
+ phy-handle = <&phy11>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan1";
+ phy-mode = "internal";
+ phy-handle = <&phy13>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-mode = "rgmii";
+ phy-handle = <&phy5>;
+ };
+
+ port@6 {
+ reg = <0x6>;
+ label = "cpu";
+ ethernet = <&eth0>;
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "lantiq,xrx200-mdio";
+ reg = <0>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+ phy5: ethernet-phy@5 {
+ reg = <0x5>;
+ };
+ phy11: ethernet-phy@11 {
+ reg = <0x11>;
+ };
+ phy13: ethernet-phy@13 {
+ reg = <0x13>;
+ };
+ };
+
+ gphy-fw {
+ compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw";
+ lantiq,rcu = <&rcu0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gphy@20 {
+ reg = <0x20>;
+
+ resets = <&reset0 31 30>;
+ reset-names = "gphy";
+ };
+
+ gphy@68 {
+ reg = <0x68>;
+
+ resets = <&reset0 29 28>;
+ reset-names = "gphy";
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt
new file mode 100644
index 000000000..30c11fea4
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt
@@ -0,0 +1,109 @@
+Marvell DSA Switch Device Tree Bindings
+---------------------------------------
+
+WARNING: This binding is currently unstable. Do not program it into a
+FLASH never to be changed again. Once this binding is stable, this
+warning will be removed.
+
+If you need a stable binding, use the old dsa.txt binding.
+
+Marvell Switches are MDIO devices. The following properties should be
+placed as a child node of an mdio device.
+
+The properties described here are those specific to Marvell devices.
+Additional required and optional properties can be found in dsa.txt.
+
+The compatibility string is used only to find an identification register,
+which is at a different MDIO base address in different switch families.
+- "marvell,mv88e6085" : Switch has base address 0x10. Use with models:
+ 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
+ 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
+ 6341, 6350, 6351, 6352
+- "marvell,mv88e6190" : Switch has base address 0x00. Use with models:
+ 6190, 6190X, 6191, 6290, 6390, 6390X
+- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model:
+ 6220, 6250
+
+Required properties:
+- compatible : Should be one of "marvell,mv88e6085",
+ "marvell,mv88e6190" or "marvell,mv88e6250" as
+ indicated above
+- reg : Address on the MII bus for the switch.
+
+Optional properties:
+
+- reset-gpios : Should be a gpio specifier for a reset line
+- interrupts : Interrupt from the switch
+- interrupt-controller : Indicates the switch is itself an interrupt
+ controller. This is used for the PHY interrupts.
+#interrupt-cells = <2> : Controller uses two cells, number and flag
+- eeprom-length : Set to the length of an EEPROM connected to the
+ switch. Must be set if the switch can not detect
+ the presence and/or size of a connected EEPROM,
+ otherwise optional.
+- mdio : Container of PHY and devices on the switches MDIO
+ bus.
+- mdio? : Container of PHYs and devices on the external MDIO
+ bus. The node must contains a compatible string of
+ "marvell,mv88e6xxx-mdio-external"
+
+Example:
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ switch0: switch@0 {
+ compatible = "marvell,mv88e6085";
+ reg = <0>;
+ reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch1phy0: switch1phy0@0 {
+ reg = <0>;
+ interrupt-parent = <&switch0>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ switch0: switch@0 {
+ compatible = "marvell,mv88e6390";
+ reg = <0>;
+ reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch1phy0: switch1phy0@0 {
+ reg = <0>;
+ interrupt-parent = <&switch0>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ mdio1 {
+ compatible = "marvell,mv88e6xxx-mdio-external";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch1phy9: switch1phy0@9 {
+ reg = <9>;
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt
new file mode 100644
index 000000000..560369efa
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt
@@ -0,0 +1,315 @@
+Mediatek MT7530 Ethernet switch
+================================
+
+Required properties:
+
+- compatible: may be compatible = "mediatek,mt7530"
+ or compatible = "mediatek,mt7621"
+ or compatible = "mediatek,mt7531"
+- #address-cells: Must be 1.
+- #size-cells: Must be 0.
+- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
+ on multi-chip module belong to MT7623A has or the remotely standalone
+ chip as the function MT7623N reference board provided for.
+
+If compatible mediatek,mt7530 is set then the following properties are required
+
+- core-supply: Phandle to the regulator node necessary for the core power.
+- io-supply: Phandle to the regulator node necessary for the I/O power.
+ See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt
+ for details for the regulator setup on these boards.
+
+If the property mediatek,mcm isn't defined, following property is required
+
+- reset-gpios: Should be a gpio specifier for a reset line.
+
+Else, following properties are required
+
+- resets : Phandle pointing to the system reset controller with
+ line index for the ethsys.
+- reset-names : Should be set to "mcm".
+
+Required properties for the child nodes within ports container:
+
+- reg: Port address described must be 6 for CPU port and from 0 to 5 for
+ user ports.
+- phy-mode: String, the following values are acceptable for port labeled
+ "cpu":
+ If compatible mediatek,mt7530 or mediatek,mt7621 is set,
+ must be either "trgmii" or "rgmii"
+ If compatible mediatek,mt7531 is set,
+ must be either "sgmii", "1000base-x" or "2500base-x"
+
+Port 5 of mt7530 and mt7621 switch is muxed between:
+1. GMAC5: GMAC5 can interface with another external MAC or PHY.
+2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC
+ of the SOC. Used in many setups where port 0/4 becomes the WAN port.
+ Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to
+ GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
+ connected to external component!
+
+Port 5 modes/configurations:
+1. Port 5 is disabled and isolated: An external phy can interface to the 2nd
+ GMAC of the SOC.
+ In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd
+ GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC!
+2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
+ It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode
+ and RGMII delay.
+3. Port 5 is muxed to GMAC5 and can interface to an external phy.
+ Port 5 becomes an extra switch port.
+ Only works on platform where external phy TX<->RX lines are swapped.
+ Like in the Ubiquiti ER-X-SFP.
+4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port.
+ Currently a 2nd CPU port is not supported by DSA code.
+
+Depending on how the external PHY is wired:
+1. normal: The PHY can only connect to 2nd GMAC but not to the switch
+2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as
+ a ethernet port. But can't interface to the 2nd GMAC.
+
+Based on the DT the port 5 mode is configured.
+
+Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
+When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
+phy-mode must be set, see also example 2 below!
+ * mt7621: phy-mode = "rgmii-txid";
+ * mt7623: phy-mode = "rgmii";
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
+required, optional properties and how the integrated switch subnodes must
+be specified.
+
+Example:
+
+ &mdio0 {
+ switch@0 {
+ compatible = "mediatek,mt7530";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ core-supply = <&mt6323_vpa_reg>;
+ io-supply = <&mt6323_vemc3v3_reg>;
+ reset-gpios = <&pio 33 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "trgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+
+Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+&eth {
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "rgmii-txid";
+ phy-handle = <&phy4>;
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Internal phy */
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+
+ mt7530: switch@1f {
+ compatible = "mediatek,mt7621";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1f>;
+ pinctrl-names = "default";
+ mediatek,mcm;
+
+ resets = <&rstctrl 2>;
+ reset-names = "mcm";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+/* Commented out. Port 4 is handled by 2nd GMAC.
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ };
+*/
+
+ cpu_port0: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+ };
+};
+
+Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY.
+
+&eth {
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* External phy */
+ ephy5: ethernet-phy@7 {
+ reg = <7>;
+ };
+
+ mt7530: switch@1f {
+ compatible = "mediatek,mt7621";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1f>;
+ pinctrl-names = "default";
+ mediatek,mcm;
+
+ resets = <&rstctrl 2>;
+ reset-names = "mcm";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "lan5";
+ phy-mode = "rgmii";
+ phy-handle = <&ephy5>;
+ };
+
+ cpu_port0: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
new file mode 100644
index 000000000..7a271d070
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
@@ -0,0 +1,213 @@
+Microchip Ocelot switch driver family
+=====================================
+
+Felix
+-----
+
+Currently the switches supported by the felix driver are:
+
+- VSC9959 (Felix)
+- VSC9953 (Seville)
+
+The VSC9959 switch is found in the NXP LS1028A. It is a PCI device, part of the
+larger ENETC root complex. As a result, the ethernet-switch node is a sub-node
+of the PCIe root complex node and its "reg" property conforms to the parent
+node bindings:
+
+* reg: Specifies PCIe Device Number and Function Number of the endpoint device,
+ in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0).
+
+It does not require a "compatible" string.
+
+The interrupt line is used to signal availability of PTP TX timestamps and for
+TSN frame preemption.
+
+For the external switch ports, depending on board configuration, "phy-mode" and
+"phy-handle" are populated by board specific device tree instances. Ports 4 and
+5 are fixed as internal ports in the NXP LS1028A instantiation.
+
+The CPU port property ("ethernet") configures the feature called "NPI port" in
+the Ocelot hardware core. The CPU port in Ocelot is a set of queues, which are
+connected, in the Node Processor Interface (NPI) mode, to an Ethernet port.
+By default, in fsl-ls1028a.dtsi, the NPI port is assigned to the internal
+2.5Gbps port@4, but can be moved to the 1Gbps port@5, depending on the specific
+use case. Moving the NPI port to an external switch port is hardware possible,
+but there is no platform support for the Linux system on the LS1028A chip to
+operate as an entire slave DSA chip. NPI functionality (and therefore DSA
+tagging) is supported on a single port at a time.
+
+Any port can be disabled (and in fsl-ls1028a.dtsi, they are indeed all disabled
+by default, and should be enabled on a per-board basis). But if any external
+switch port is enabled at all, the ENETC PF2 (enetc_port2) should be enabled as
+well, regardless of whether it is configured as the DSA master or not. This is
+because the Felix PHYLINK implementation accesses the MAC PCS registers, which
+in hardware truly belong to the ENETC port #2 and not to Felix.
+
+Supported PHY interface types (appropriate SerDes protocol setting changes are
+needed in the RCW binary):
+
+* phy_mode = "internal": on ports 4 and 5
+* phy_mode = "sgmii": on ports 0, 1, 2, 3
+* phy_mode = "qsgmii": on ports 0, 1, 2, 3
+* phy_mode = "usxgmii": on ports 0, 1, 2, 3
+* phy_mode = "2500base-x": on ports 0, 1, 2, 3
+
+For the rest of the device tree binding definitions, which are standard DSA and
+PCI, refer to the following documents:
+
+Documentation/devicetree/bindings/net/dsa/dsa.txt
+Documentation/devicetree/bindings/pci/pci.txt
+
+Example:
+
+&soc {
+ pcie@1f0000000 { /* Integrated Endpoint Root Complex */
+ ethernet-switch@0,5 {
+ reg = <0x000500 0 0 0 0>;
+ /* IEP INT_B */
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* External ports */
+ port@0 {
+ reg = <0>;
+ label = "swp0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "swp1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "swp2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "swp3";
+ };
+
+ /* Tagging CPU port */
+ port@4 {
+ reg = <4>;
+ ethernet = <&enetc_port2>;
+ phy-mode = "internal";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+ };
+
+ /* Non-tagging CPU port */
+ port@5 {
+ reg = <5>;
+ phy-mode = "internal";
+ status = "disabled";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
+
+The VSC9953 switch is found inside NXP T1040. It is a platform device with the
+following required properties:
+
+- compatible:
+ Must be "mscc,vsc9953-switch".
+
+Supported PHY interface types (appropriate SerDes protocol setting changes are
+needed in the RCW binary):
+
+* phy_mode = "internal": on ports 8 and 9
+* phy_mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7
+* phy_mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7
+
+Example:
+
+&soc {
+ ethernet-switch@800000 {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ compatible = "mscc,vsc9953-switch";
+ little-endian;
+ reg = <0x800000 0x290000>;
+
+ ports {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ port@0 {
+ reg = <0x0>;
+ label = "swp0";
+ };
+
+ port@1 {
+ reg = <0x1>;
+ label = "swp1";
+ };
+
+ port@2 {
+ reg = <0x2>;
+ label = "swp2";
+ };
+
+ port@3 {
+ reg = <0x3>;
+ label = "swp3";
+ };
+
+ port@4 {
+ reg = <0x4>;
+ label = "swp4";
+ };
+
+ port@5 {
+ reg = <0x5>;
+ label = "swp5";
+ };
+
+ port@6 {
+ reg = <0x6>;
+ label = "swp6";
+ };
+
+ port@7 {
+ reg = <0x7>;
+ label = "swp7";
+ };
+
+ port@8 {
+ reg = <0x8>;
+ phy-mode = "internal";
+ ethernet = <&enet0>;
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+ };
+
+ port@9 {
+ reg = <0x9>;
+ phy-mode = "internal";
+ status = "disabled";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
new file mode 100644
index 000000000..ccbc6d893
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
@@ -0,0 +1,175 @@
+* Qualcomm Atheros QCA8xxx switch family
+
+Required properties:
+
+- compatible: should be one of:
+ "qca,qca8334"
+ "qca,qca8337"
+
+- #size-cells: must be 0
+- #address-cells: must be 1
+
+Optional properties:
+
+- reset-gpios: GPIO to be used to reset the whole device
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
+mdio-bus each subnode describing a port needs to have a valid phandle
+referencing the internal PHY it is connected to. This is because there's no
+N:N mapping of port and PHY id.
+
+Don't use mixed external and internal mdio-bus configurations, as this is
+not supported by the hardware.
+
+The CPU port of this switch is always port 0.
+
+A CPU port node has the following optional node:
+
+- fixed-link : Fixed-link subnode describing a link to a non-MDIO
+ managed entity. See
+ Documentation/devicetree/bindings/net/fixed-link.txt
+ for details.
+
+For QCA8K the 'fixed-link' sub-node supports only the following properties:
+
+- 'speed' (integer, mandatory), to indicate the link speed. Accepted
+ values are 10, 100 and 1000
+- 'full-duplex' (boolean, optional), to indicate that full duplex is
+ used. When absent, half duplex is assumed.
+
+Examples:
+
+for the external mdio-bus configuration:
+
+ &mdio0 {
+ phy_port1: phy@0 {
+ reg = <0>;
+ };
+
+ phy_port2: phy@1 {
+ reg = <1>;
+ };
+
+ phy_port3: phy@2 {
+ reg = <2>;
+ };
+
+ phy_port4: phy@3 {
+ reg = <3>;
+ };
+
+ phy_port5: phy@4 {
+ reg = <4>;
+ };
+
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = 1000;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy_port1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy_port2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy_port3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ phy-handle = <&phy_port4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-handle = <&phy_port5>;
+ };
+ };
+ };
+ };
+
+for the internal master mdio-bus configuration:
+
+ &mdio0 {
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = 1000;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
new file mode 100644
index 000000000..b6ae8541b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
@@ -0,0 +1,153 @@
+Realtek SMI-based Switches
+==========================
+
+The SMI "Simple Management Interface" is a two-wire protocol using
+bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
+not use the MDIO protocol. This binding defines how to specify the
+SMI-based Realtek devices.
+
+Required properties:
+
+- compatible: must be exactly one of:
+ "realtek,rtl8366"
+ "realtek,rtl8366rb" (4+1 ports)
+ "realtek,rtl8366s" (4+1 ports)
+ "realtek,rtl8367"
+ "realtek,rtl8367b"
+ "realtek,rtl8368s" (8 port)
+ "realtek,rtl8369"
+ "realtek,rtl8370" (8 port)
+
+Required properties:
+- mdc-gpios: GPIO line for the MDC clock line.
+- mdio-gpios: GPIO line for the MDIO data line.
+- reset-gpios: GPIO line for the reset signal.
+
+Optional properties:
+- realtek,disable-leds: if the LED drivers are not used in the
+ hardware design this will disable them so they are not turned on
+ and wasting power.
+
+Required subnodes:
+
+- interrupt-controller
+
+ This defines an interrupt controller with an IRQ line (typically
+ a GPIO) that will demultiplex and handle the interrupt from the single
+ interrupt line coming out of one of the SMI-based chips. It most
+ importantly provides link up/down interrupts to the PHY blocks inside
+ the ASIC.
+
+Required properties of interrupt-controller:
+
+- interrupt: parent interrupt, see interrupt-controller/interrupts.txt
+- interrupt-controller: see interrupt-controller/interrupts.txt
+- #address-cells: should be <0>
+- #interrupt-cells: should be <1>
+
+- mdio
+
+ This defines the internal MDIO bus of the SMI device, mostly for the
+ purpose of being able to hook the interrupts to the right PHY and
+ the right PHY to the corresponding port.
+
+Required properties of mdio:
+
+- compatible: should be set to "realtek,smi-mdio" for all SMI devices
+
+See net/mdio.txt for additional MDIO bus properties.
+
+See net/dsa/dsa.txt for a list of additional required and optional properties
+and subnodes of DSA switches.
+
+Examples:
+
+switch {
+ compatible = "realtek,rtl8366rb";
+ /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+ mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+
+ switch_intc: interrupt-controller {
+ /* GPIO 15 provides the interrupt */
+ interrupt-parent = <&gpio0>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ phy-handle = <&phy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy3>;
+ };
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ phy-handle = <&phy4>;
+ };
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio", "dsa-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <0>;
+ };
+ phy1: phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <1>;
+ };
+ phy2: phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <2>;
+ };
+ phy3: phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <3>;
+ };
+ phy4: phy@4 {
+ reg = <4>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <12>;
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/sja1105.txt b/Documentation/devicetree/bindings/net/dsa/sja1105.txt
new file mode 100644
index 000000000..13fd21074
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/sja1105.txt
@@ -0,0 +1,156 @@
+NXP SJA1105 switch driver
+=========================
+
+Required properties:
+
+- compatible:
+ Must be one of:
+ - "nxp,sja1105e"
+ - "nxp,sja1105t"
+ - "nxp,sja1105p"
+ - "nxp,sja1105q"
+ - "nxp,sja1105r"
+ - "nxp,sja1105s"
+
+ Although the device ID could be detected at runtime, explicit bindings
+ are required in order to be able to statically check their validity.
+ For example, SGMII can only be specified on port 4 of R and S devices,
+ and the non-SGMII devices, while pin-compatible, are not equal in terms
+ of support for RGMII internal delays (supported on P/Q/R/S, but not on
+ E/T).
+
+Optional properties:
+
+- sja1105,role-mac:
+- sja1105,role-phy:
+ Boolean properties that can be assigned under each port node. By
+ default (unless otherwise specified) a port is configured as MAC if it
+ is driving a PHY (phy-handle is present) or as PHY if it is PHY-less
+ (fixed-link specified, presumably because it is connected to a MAC).
+ The effect of this property (in either its implicit or explicit form)
+ is:
+ - In the case of MII or RMII it specifies whether the SJA1105 port is a
+ clock source or sink for this interface (not applicable for RGMII
+ where there is a Tx and an Rx clock).
+ - In the case of RGMII it affects the behavior regarding internal
+ delays:
+ 1. If sja1105,role-mac is specified, and the phy-mode property is one
+ of "rgmii-id", "rgmii-txid" or "rgmii-rxid", then the entity
+ designated to apply the delay/clock skew necessary for RGMII
+ is the PHY. The SJA1105 MAC does not apply any internal delays.
+ 2. If sja1105,role-phy is specified, and the phy-mode property is one
+ of the above, the designated entity to apply the internal delays
+ is the SJA1105 MAC (if hardware-supported). This is only supported
+ by the second-generation (P/Q/R/S) hardware. On a first-generation
+ E or T device, it is an error to specify an RGMII phy-mode other
+ than "rgmii" for a port that is in fixed-link mode. In that case,
+ the clock skew must either be added by the MAC at the other end of
+ the fixed-link, or by PCB serpentine traces on the board.
+ These properties are required, for example, in the case where SJA1105
+ ports are at both ends of a MII/RMII PHY-less setup. One end would need
+ to have sja1105,role-mac, while the other sja1105,role-phy.
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard
+DSA required and optional properties.
+
+Other observations
+------------------
+
+The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least
+one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
+cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
+depends on the SPI bus master driver.
+
+Example
+-------
+
+Ethernet switch connected via SPI to the host, CPU port wired to enet2:
+
+arch/arm/boot/dts/ls1021a-tsn.dts:
+
+/* SPI controller of the LS1021 */
+&dspi0 {
+ sja1105@1 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "nxp,sja1105t";
+ spi-max-frequency = <4000000>;
+ fsl,spi-cs-sck-delay = <1000>;
+ fsl,spi-sck-cs-delay = <1000>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ /* ETH5 written on chassis */
+ label = "swp5";
+ phy-handle = <&rgmii_phy6>;
+ phy-mode = "rgmii-id";
+ reg = <0>;
+ /* Implicit "sja1105,role-mac;" */
+ };
+ port@1 {
+ /* ETH2 written on chassis */
+ label = "swp2";
+ phy-handle = <&rgmii_phy3>;
+ phy-mode = "rgmii-id";
+ reg = <1>;
+ /* Implicit "sja1105,role-mac;" */
+ };
+ port@2 {
+ /* ETH3 written on chassis */
+ label = "swp3";
+ phy-handle = <&rgmii_phy4>;
+ phy-mode = "rgmii-id";
+ reg = <2>;
+ /* Implicit "sja1105,role-mac;" */
+ };
+ port@3 {
+ /* ETH4 written on chassis */
+ phy-handle = <&rgmii_phy5>;
+ label = "swp4";
+ phy-mode = "rgmii-id";
+ reg = <3>;
+ /* Implicit "sja1105,role-mac;" */
+ };
+ port@4 {
+ /* Internal port connected to eth2 */
+ ethernet = <&enet2>;
+ phy-mode = "rgmii";
+ reg = <4>;
+ /* Implicit "sja1105,role-phy;" */
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
+
+/* MDIO controller of the LS1021 */
+&mdio0 {
+ /* BCM5464 */
+ rgmii_phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+ rgmii_phy4: ethernet-phy@4 {
+ reg = <0x4>;
+ };
+ rgmii_phy5: ethernet-phy@5 {
+ reg = <0x5>;
+ };
+ rgmii_phy6: ethernet-phy@6 {
+ reg = <0x6>;
+ };
+};
+
+/* Ethernet master port of the LS1021 */
+&enet2 {
+ phy-connection-type = "rgmii";
+ status = "ok";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt
new file mode 100644
index 000000000..bbf4a13f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt
@@ -0,0 +1,131 @@
+Vitesse VSC73xx Switches
+========================
+
+This defines device tree bindings for the Vitesse VSC73xx switch chips.
+The Vitesse company has been acquired by Microsemi and Microsemi has
+been acquired Microchip but retains this vendor branding.
+
+The currently supported switch chips are:
+Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
+Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
+
+This switch could have two different management interface.
+
+If SPI interface is used, the device tree node is an SPI device so it must
+reside inside a SPI bus device tree node, see spi/spi-bus.txt
+
+When the chip is connected to a parallel memory bus and work in memory-mapped
+I/O mode, a platform device is used to represent the vsc73xx. In this case it
+must reside inside a platform bus device tree node.
+
+Required properties:
+
+- compatible: must be exactly one of:
+ "vitesse,vsc7385"
+ "vitesse,vsc7388"
+ "vitesse,vsc7395"
+ "vitesse,vsc7398"
+- gpio-controller: indicates that this switch is also a GPIO controller,
+ see gpio/gpio.txt
+- #gpio-cells: this must be set to <2> and indicates that we are a twocell
+ GPIO controller, see gpio/gpio.txt
+
+Optional properties:
+
+- reset-gpios: a handle to a GPIO line that can issue reset of the chip.
+ It should be tagged as active low.
+
+Required subnodes:
+
+See net/dsa/dsa.txt for a list of additional required and optional properties
+and subnodes of DSA switches.
+
+Examples:
+
+SPI:
+switch@0 {
+ compatible = "vitesse,vsc7395";
+ reg = <0>;
+ /* Specified for 2.5 MHz or below */
+ spi-max-frequency = <2500000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ vsc: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+Platform:
+switch@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "vitesse,vsc7385";
+ reg = <0x2 0x0 0x20000>;
+ reset-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ vsc: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&enet0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+
+};
generated by cgit v1.2.3 (git 2.39.1) at 2024-08-27 09:40:28 +0000